Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 2: Cut-back and fluxed bituminous binders

This document specifies a method for the determination of the efflux time at 25 °C of petroleum cut-back and fluxed bituminous binders in seconds using an efflux viscometer. Alternative test temperatures are 40 °C, 50 °C and 60 °C.
WARNING - The use of this document involves hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels Ausflussviskosimeter - Teil 2: Verschnittene und gefluxte bitumenhaltige Bindemittel

Dieses Dokument legt ein Verfahren zur Bestimmung der Ausflusszeit in Sekunden von petrostämmig verschnittenen und gefluxten bitumenhaltigen Bindemitteln bei 25 °C unter Anwendung eines Ausfluss-viskosimeters fest. Alternative Prüftemperaturen sind 40 °C, 50 °C und 60 °C.
WARNUNG - Die Anwendung dieses Dokument schließt den Umgang mit gefährlichen Substanzen und Ausrüstungen sowie die Durchführung gefährlicher Arbeitsschritte ein. Dieses Dokument erhebt nicht den Anspruch, dass alle mit seiner Anwendung verbundenen Sicherheitsprobleme angesprochen werden. Es liegt in der Verantwortung des Anwenders dieses Dokuments, geeignete Vorsichtsmaßnahmen für den Arbeits- und Gesundheitsschutz zu treffen und die Anwendbarkeit einschränkender Vorschriften vor der Anwendung zu bestimmen.

Bitumes et liants bitumineux - Détermination du temps d'écoulement à l'aide d'un viscosimètre à écoulement - Partie 2 : Bitumes fluidifés et fluxés

Le présent document spécifie une méthode de détermination du temps d’écoulement, en secondes, à 25 °C, des bitumes fluidifiés et fluxés, à l’aide d’un viscosimètre à écoulement. D’autres températures d’essai possibles sont 40 °C, 50 °C et 60 °C.
AVERTISSEMENT - L'utilisation de ce document peut impliquer le recours à des produits, des opérations et des équipements à caractère dangereux. Le présent document n'est pas censé aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l'utilisateur de ce document d'établir des règles de sécurité et d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.

Bitumen in bitumenska veziva - Določanje viskoznosti z iztočnim viskozimetrom - 2. del: Rezana in fluksirana bitumenska veziva

Ta dokument določa metodo za določanje časa iztoka naftnih rezanih in fluksiranih bitumenskih veziv pri 25 °C v sekundah z uporabo iztočnega viskozimetra. Alternativne preskusne temperature so 40 °C, 50 °C in 60 °C.
OPOZORILO: Pri uporabi tega dokumenta so prisotni nevarni materiali, postopki in oprema. Ta dokument ne obravnava vseh varnostnih težav, ki se navezujejo na njegovo uporabo. Za vzpostavitev ustreznih varnostnih in zdravstvenih praks ter za določitev uporabnosti regulativnih omejitev pred uporabo je odgovoren uporabnik tega dokumenta.

General Information

Status
Published
Public Enquiry End Date
28-Oct-2021
Publication Date
08-Mar-2023
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
17-Feb-2023
Due Date
24-Apr-2023
Completion Date
09-Mar-2023

Relations

Buy Standard

Standard
EN 12846-2:2023
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 12846-2:2021
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 12846-2:2023
01-april-2023
Nadomešča:
SIST EN 12846-2:2011
Bitumen in bitumenska veziva - Določanje viskoznosti z iztočnim viskozimetrom -
2. del: Rezana in fluksirana bitumenska veziva
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer -
Part 2: Cut-back and fluxed bituminous binders
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels
Ausflussviskosimeter - Teil 2: Verschnittene und gefluxte bitumenhaltige Bindemittel
Bitumes et liants bitumineux - Détermination du temps d'écoulement à l'aide d'un
viscosimètre à écoulement - Partie 2 : Bitumes fluidifés et fluxés
Ta slovenski standard je istoveten z: EN 12846-2:2022
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
SIST EN 12846-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 12846-2:2023

---------------------- Page: 2 ----------------------
SIST EN 12846-2:2023


EN 12846-2
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2022
EUROPÄISCHE NORM
ICS 91.100.50 Supersedes EN 12846-2:2011
English Version

Bitumen and bituminous binders - Determination of efflux
time by the efflux viscometer - Part 2: Cut-back and fluxed
bituminous binders
Bitumes et liants bitumineux - Détermination du temps Bitumen und bitumenhaltige Bindemittel -
d'écoulement à l'aide d'un viscosimètre à écoulement - Bestimmung der Ausflusszeit mittels
Partie 2 : Bitumes fluidifiés et fluxés Ausflussviskosimeter - Teil 2: Verschnittene und
gefluxte bitumenhaltige Bindemittel
This European Standard was approved by CEN on 21 November 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12846-2:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 12846-2:2023
EN 12846-2:2022 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 5
5 Reagents and materials . 5
6 Apparatus . 5
7 Sampling . 6
8 Procedure. 6
8.1 General . 6
8.2 Preparation of apparatus . 6
8.3 Measurement . 7
9 Expression of results . 8
10 Precision . 8
10.1 Repeatability . 8
10.2 Reproducibility . 8
11 Test report . 9
Bibliography . 13

2

---------------------- Page: 4 ----------------------
SIST EN 12846-2:2023
EN 12846-2:2022 (E)
European foreword
This document (EN 12846-2:2022) has been prepared by Technical Committee CEN/TC 336 “Bituminous
binders”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2023, and conflicting national standards shall be
withdrawn at the latest by June 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12846-2:2011.
EN 12846-2:2022 includes the following significant technical changes with respect to EN 12846-2:2011:
— possibility to use a vegetal oil, requirement on density replaces requirement on viscosity (Clause 5);
— Figures 1 and 2 have been modified to be in line with the evolution of test equipment (6.1 and 6.2);
— possibility to use alternative working apparatus that meet the requirements of this document, such
as an integrated block viscometer (6.1);
— mercury stem thermometers are no longer specified as reference thermometers (6.4) and Annex A
has been removed;
— more accurate description of measurement procedure (8.3).
The EN 12846 series consists of the following parts under the general title Bitumen and bituminous
binders — Determination of efflux time by the efflux viscometer:
— Part 1: Bituminous emulsions;
— Part 2: Cut-back and fluxed bituminous binders.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
3

---------------------- Page: 5 ----------------------
SIST EN 12846-2:2023
EN 12846-2:2022 (E)
1 Scope
This document specifies a method for the determination of the efflux time at 25 °C of petroleum cut-back
and fluxed bituminous binders in seconds using an efflux viscometer. Alternative test temperatures are
40 °C, 50 °C and 60 °C.
WARNING — The use of this document involves hazardous materials, operations and equipment. This
document does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this document to establish appropriate safety and health practices and to
determine the applicability of regulatory limitations prior to use.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 58, Bitumen and bituminous binders — Sampling bituminous binders
EN 12594, Bitumen and bituminous binders — Preparation of test samples
EN 13302, Bitumen and bituminous binders — Determination of dynamic viscosity of bituminous binder
using a rotating spindle apparatus
EN ISO 4788:2005, Laboratory glassware — Graduated measuring cylinders (ISO 4788:2005)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org
3.1
viscosity
internal resistance of a fluid to flow
3.2
efflux time
time needed for a specified volume of a material to flow through a specified orifice at a specified
temperature
Note 1 to entry: The efflux time is an indirect measure of the viscosity and is also referred to as “pseudo-
viscosity”.
4

---------------------- Page: 6 ----------------------
SIST EN 12846-2:2023
EN 12846-2:2022 (E)
4 Principle
The efflux time of a petroleum cut-back or fluxed bituminous binder is determined using an efflux
viscometer known as the Standard Tar Viscometer (STV) which determines the time of efflux of a 50 ml
sample through a 10 mm or a 4 mm orifice at a specified temperature.
Whatever temperatures or orifice diameters used, the efflux time shall not exceed 600 s. For highly
viscous cut-back or fluxed bituminous binders, EN 13302 shall be used.
5 Reagents and materials
3
Light mineral or vegetal oil having a density lower or equal to 930 kg/m at 15 °C.
6 Apparatus
Usual laboratory apparatus and glassware, together with the following.
6.1 Efflux viscometer (example of assembled viscometer on Figure 1) consisting essentially of a cup
with an orifice in the centre of the base that may be
...

SLOVENSKI STANDARD
oSIST prEN 12846-2:2021
01-oktober-2021
Bitumen in bitumenska veziva - Določanje viskoznosti z iztočnim viskozimetrom -
2. del: Rezana in fluksirana bitumenska veziva
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer -
Part 2: Cut-back and fluxed bituminous binders
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels
Ausflussviskosimeter - Teil 2: Verschnittene und gefluxte bitumenhaltige Bindemittel
Bitumes et liants bitumineux - Détermination du temps d'écoulement à l'aide d'un
viscosimètre à écoulement - Partie 2 : Bitumes fluidifés et fluxés
Ta slovenski standard je istoveten z: prEN 12846-2
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN 12846-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12846-2:2021

---------------------- Page: 2 ----------------------
oSIST prEN 12846-2:2021


DRAFT
EUROPEAN STANDARD
prEN 12846-2
NORME EUROPÉENNE

EUROPÄISCHE NORM

August 2021
ICS 91.100.50 Will supersede EN 12846-2:2011
English Version

Bitumen and bituminous binders - Determination of efflux
time by the efflux viscometer - Part 2: Cut-back and fluxed
bituminous binders
Bitumes et liants bitumineux - Détermination du temps Bitumen und bitumenhaltige Bindemittel -
d'écoulement à l'aide d'un viscosimètre à écoulement - Bestimmung der Ausflusszeit mittels
Partie 2 : Bitumes fluidifés et fluxés Ausflussviskosimeter - Teil 2: Verschnittene und
gefluxte bitumenhaltige Bindemittel
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 336.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12846-2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12846-2:2021
prEN 12846-2:2021 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Reagents and materials . 5
5.1 Light mineral or vegetal oil . 5
6 Apparatus . 5
7 Sampling . 6
8 Procedure. 6
8.1 General . 6
8.2 Preparation of apparatus . 6
8.3 Measurement . 6
9 Expression of results . 8
10 Precision . 8
10.1 Repeatability . 8
10.2 Reproducibility . 8
10.3 Test report . 8
Bibliography . 12
2

---------------------- Page: 4 ----------------------
oSIST prEN 12846-2:2021
prEN 12846-2:2021 (E)
European foreword
This document (prEN 12846-2:2021) has been prepared by Technical Committee CEN/TC 336
“Bituminous binders”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12846-2:2011.
The main technical changes are:
— possibility to use a vegetal oil, requirement on density replaces requirement on viscosity (5.1);
— Figures 1 and 2 have been modified to be in line with the evolution of test equipment (6.1 and 6.2);
— possibility to use alternate working apparatus that meet the requirements of this document, such as
an integrated block viscometer (6.1);
— mercury stem thermometers are no longer specified as reference thermometers (6.4) and Annex A
has been removed;
— more accurate description of measurement procedure (8.3).
The EN 12846 series consists of the following parts under the general title Bitumen and bituminous
binders — Determination of efflux time by the efflux viscometer:
— Part 1: Bituminous emulsions;
— Part 2: Cut-back and fluxed bituminous binders.
3

---------------------- Page: 5 ----------------------
oSIST prEN 12846-2:2021
prEN 12846-2:2021 (E)
1 Scope
This document specifies a method for the determination of the efflux time at 25 °C of petroleum cut-back
and fluxed bituminous binders in seconds using an efflux viscometer. Alternative test temperatures are
40 °C, 50 °C and 60 °C.
WARNING — The use of this document involves hazardous materials, operations and equipment. This
document does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this document to establish appropriate safety and health practices and to
determine the applicability of regulatory limitations prior to use.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 58, Bitumen and bituminous binders — Sampling bituminous binders
EN 12594, Bitumen and bituminous binders — Preparation of test samples
EN 13302, Bitumen and bituminous binders — Determination of dynamic viscosity of bituminous binder
using a rotating spindle apparatus
EN ISO 4788, Laboratory glassware — Graduated measuring cylinders (ISO 4788)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
viscosity
internal resistance of a fluid to flow
3.2
efflux time
time needed for a specified volume of a material to flow through a specified orifice at a specified
temperature
Note 1 to entry: The efflux time is an indirect measure of the viscosity and is also referred to as “pseudo-
viscosity”.
4 Principle
The efflux time of a petroleum cut-back or fluxed bituminous binder is determined using an efflux
viscometer known as the Standard Tar Viscometer (STV) which determines the time of efflux of a 50 ml
sample through a 4 mm or a 10 mm orifice at a specified temperature.
Whatever temperatures or orifice diameters used, the efflux time shall not exceed 600 s. For highly
viscous cut-back or fluxed bituminous binders, EN 13302 shall be used.
4

---------------------- Page: 6 ----------------------
oSIST prEN 12846-2:2021
prEN 12846-2:2021 (E)
5 Reagents and materials
5.1 Light mineral or vegetal oil
3
Light mineral or vegetal oil having a density lower or equal to 900 kg/m at 15 °C.
6 Apparatus
Usual laboratory apparatus and glassware, together with the following.
6.1 Efflux viscometer (example of assembled viscometer on Figure 1) consisting essentially of a cup
with an orifice in the centre of the base which may be closed by a ball-and-socket valve (Figure 3).
Two forms are required, differing only in the size of the orifice (10 mm and 4 mm). For other dimensions
of the cup and the ball-valve, see Figure 3. The cup cylinder shall be made of brass. The ball valve should
be made of corrosion-resistant metal, with a ball on a rod, a levelling peg attached to the rod and a
hem
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.