EN ISO 15630-2:2010
(Main)Steel for the reinforcement and prestressing of concrete - Test methods - Part 2: Welded fabric (ISO 15630-2:2010)
Steel for the reinforcement and prestressing of concrete - Test methods - Part 2: Welded fabric (ISO 15630-2:2010)
ISO 15630-2:2010 specifies test methods applicable to welded fabric for the reinforcement of concrete.
Stähle für die Bewehrung und das Vorspannen von Beton - Prüfverfahren - Teil 2: Geschweißte Matten (ISO 15630-2:2010)
Dieser Teil von ISO 15630 legt die für geschweißte Matten in Betracht kommenden Prüfmethoden fest.
ANMERKUNG In einigen Ländern wird der Begriff "Geschweißte Drahtbewehrung" an Stellen von "Geschweißte
(Draht) Matte" verwendet.
Für nicht in diesem Teil der ISO 15630 festgelegte Prüfungen (z. B. Biegeprüfung, Rippen-/Profil-Geometrie,
Masse je Meter) ist ISO 15630-1 anwendbar.
Aciers pour l'armature et la précontrainte du béton - Méthodes d'essai - Partie 2: Treillis soudés (ISO 15630-2:2010)
L'ISO 15630-2:2010 spécifie des méthodes d'essai applicables aux treillis soudés pour l'armature du béton.
Jeklo za armiranje in prednapenjanje betona - Metode preskušanja - 2. del: Armaturne mreže (ISO 15630-2:2010)
Ta del ISO 15630 določa preskusne metode, ki veljajo za armaturne mreže za armiranje betona. Za preskuse, ki niso opredeljeni v tem delu ISO 15630 (npr. preskus upogibanja, geometrija rebra/vtiska, masa na meter), velja ISO 15630-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2011
1DGRPHãþD
SIST EN ISO 15630-2:2003
Jeklo za armiranje in prednapenjanje betona - Metode preskušanja - 2. del:
Armaturne mreže (ISO 15630-2:2010)
Steel for the reinforcement and prestressing of concrete - Test methods - Part 2: Welded
fabric (ISO 15630-2:2010)
Stähle für die Bewehrung und das Vorspannen von Beton - Prüfverfahren - Teil 2:
Geschweißte Mappen (ISO 15630-2:2010)
Aciers pour l'armature et la précontrainte du béton - Méthodes d'essai - Partie 2: Treillis
soudés (ISO 15630-2:2010)
Ta slovenski standard je istoveten z: EN ISO 15630-2:2010
ICS:
77.140.15 Jekla za armiranje betona Steels for reinforcement of
concrete
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15630-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2010
ICS 77.140.15 Supersedes EN ISO 15630-2:2002
English Version
Steel for the reinforcement and prestressing of concrete - Test
methods - Part 2: Welded fabric (ISO 15630-2:2010)
Aciers pour l'armature et la précontrainte du béton - Stähle für die Bewehrung und das Vorspannen von Beton -
Méthodes d'essai - Partie 2: Treillis soudés (ISO 15630- Prüfverfahren - Teil 2: Geschweißte Matten (ISO 15630-
2:2010) 2:2010)
This European Standard was approved by CEN on 14 October 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15630-2:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 15630-2:2010 has been prepared by Technical Committee ISO/TC 17 “Steel” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 15630-2:2010 by
Technical Committee ECISS/TC 104 “Concrete reinforcing and prestressing steels” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2011, and conflicting national standards shall be withdrawn at the
latest by April 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15630-2:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15630-2:2010 has been approved by CEN as a EN ISO 15630-2:2010 without any
modification.
INTERNATIONAL ISO
STANDARD 15630-2
Second edition
2010-10-15
Steel for the reinforcement and
prestressing of concrete — Test
methods —
Part 2:
Welded fabric
Aciers pour l'armature et la précontrainte du béton — Méthodes
d'essai —
Partie 2: Treillis soudés
Reference number
ISO 15630-2:2010(E)
©
ISO 2010
ISO 15630-2:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 15630-2:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Symbols.1
4 General provisions concerning test pieces.2
5 Tensile test.3
5.1 Test piece .3
5.2 Test equipment .3
5.3 Test procedure.3
6 Bend test on welded intersection .4
6.1 Test piece .4
6.2 Test equipment .4
6.3 Test procedure.5
6.4 Interpretation of test results.5
7 Determination of the weld shear force (F ).6
s
7.1 Test piece .6
7.2 Test equipment .6
7.3 Test procedure.11
8 Axial force fatigue test.11
8.1 Principle of test.11
8.2 Test piece .11
8.3 Test equipment .11
8.4 Test procedure.12
8.4.1 Provisions concerning the test piece.12
8.4.2 Upper force (F ) and force range (F ).12
up r
8.4.3 Stability of force and frequency.12
8.4.4 Counting of force cycles.12
8.4.5 Frequency.12
8.4.6 Temperature.12
8.4.7 Validity of the test.12
9 Chemical analysis .12
10 Measurement of the geometrical characteristics of the fabric.13
10.1 Test piece .13
10.2 Test equipment .13
10.3 Test procedure.13
11 Test report.13
Bibliography.14
ISO 15630-2:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15630-2 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 16, Steels for the
reinforcement and prestressing of concrete.
This second edition cancels and replaces the first edition (ISO 15630-2:2002), which has been technically
revised.
ISO 15630 consists of the following parts, under the general title Steel for the reinforcement and prestressing
of concrete — Test methods:
⎯ Part 1: Reinforcing bars, wire rod and wire
⎯ Part 2: Welded fabric
⎯ Part 3: Prestressing steel
iv © ISO 2010 – All rights reserved
ISO 15630-2:2010(E)
Introduction
The aim of ISO 15630 is to provide all relevant test methods for r
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.