SC 23J - Switches for appliances

IEC 61020-1:2019 specifies the terminology, symbols, test methods and other necessary information to provide consistency in detail specifications for electromechanical switches.
This document relates to electromechanical switches intended for use in electrical and electronic appliances. Switches covered by this document:
a) are devices which open, close, or change the connection of a circuit by the mechanical motion of conducting parts (contacts);
b) have a maximum rated voltage of 480 V;
c) have a maximum rated current of 63 A.
This third edition cancels and replaces the second edition published in 2009.
This edition includes the following significant technical changes with respect to the previous edition:
a) In accordance with the ISO/IEC Directives, Part 2:2016, Clause 2 General has been replaced by two new clauses: Clause 2 Normative references and Clause 3 Terms, definitions, units and symbols.
2.4 Preferred values and 2.5 Marking have been moved to Clauses 5 and 6. In addition, 6.2 Markings on packaging has been added.
b) Clause 3 Quality assurance procedures and Annex A have been deleted.
c) 4.3.6.3 Returning force has been added.
d) 4.3.6.4 Travel (movement of the actuator) has been added.
e) 4.12 Environmental testing:
4.12.1.3 and 4.12.1.5 have been renumbered 4.12.2 and 4.12.3, respectively. 4.12.1.4 and 4.12.1.7 have been integrated in 4.12.5. 4.12.10 Salt mist has been added.
f) Following publication of IEC 61058-1-1:2016, some cross-references to IEC 61058-1 have been updated.
g) The following items have been updated with respect to the second edition.
- Tables and figures:
Tables 1 and 3 have been deleted, Table 4 has been renumbered to Table 10. New Tables 2, 3, 4, 5, 6, 7, 8 and 9 have been added.
Figure 1 has been renumbered to Figure 3, Figure 2 renumbered to Figure 4, Figure 3 renumbered to Figure 9 and Figure 4 renumbered to Figure 12. Added new Figures 1, 2, 5, 6, 7, 8, 10 and 11 have been added.
- Specific words and common names have been unified.

IEC 61058-2-6:2018 is a subset based on IEC 61058-1. The clauses outlined below are intended to address the specific requirements for switches incorporated into or integrated with electric motor-operated hand-held tools, transportable tools and lawn and garden machinery.
This document is intended for switches with an ambient temperature up to and including 55 °C. Switches tested according to IEC 61058-1 are considered to comply with this document and additional testing is not required provided ratings, loads, and endurance are correct.
This second edition cancels and replaces the first edition published in 2016. It constitutes a technical revision.
This edition includes the following significant change with respect to the previous edition:
Overall format to support IEC 61058-1, IEC 61058-1-1 and IEC 61058-1-2.

IEC 61058-2-5:2018 applies to change-over selectors (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. This third edition cancels and replaces the second edition published in 2010 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- updated references due to new structure of IEC 61058-1;
- changes on conducting the heating test due to the corresponding changes in IEC 61058-1.

IEC 61058-2-4:2018 applies to independently mounted switches for appliances (mechanical or electronic) actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. This second edition cancels and replaces the first edition published in 1995 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- overall format modified to support the revised structure of the series;
- Annexes K and M have been included as an integral part of this document;
- Annex L has been included for information purposes only.
This document is to be used in conjunction with IEC 61058-1:2016.

IEC 61058-2-1:2018 applies to cord switches (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A.
This third edition cancels and replaces the second edition published in 2010 and constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
Overall format to support IEC 61058-1, IEC 61058-1-1, IEC 61058-1-2, and the heating tests.

IEC 61058-1:2016 applies to switches for appliances. The switches are intended to control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. This fourth edition cancels and replaces the third edition published in 2000, Amendment 1:2001 and Amendment 2:2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) requirements for mechanical switches are now given in IEC 61058-1-1;
b) requirements for electronic switches are now given in IEC 61058-1-2.

IEC 61058-2-6:2016 is a subset based on IEC 61058-1. The clauses outlined below are intended to address the specific requirements for switches incorporated into or integrated with electric motor-operated hand-held tools, transportable tools and lawn and garden machinery. This standard is intended for switches with an ambient temperature up to and including 55 °C. Switches tested to IEC 61058-1 are considered to comply with this standard and additional testing is not required provided ratings, loads, and endurance are correct.
This publication is to be read in conjunction with IEC 61058-1:2000.

IEC 61058-1-1:2016 applies to mechanical switching devices and and shall be used in conjunction with the requirements of IEC 61058-1.
This publication is to be read in conjunction with IEC 61058-1:2016

IEC 61058-1-2:2016 applies to electronic switching devices and
This publication is to be read in conjunction with IEC 61058-1:2000

IEC 61058-2-5:2010 applies to change-over selectors (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. This second edition cancels and replaces the first edition published in 1994 and constitutes a technical revision. The main changes from the first edition are as follows:
- scope;
- abnormal operation and fault conditions for electronic switches;
- components for electronic switches;
- EMC requirements.
This publication is to be read in conjunction with IEC 61058-1:2000.

IEC 61058-2-1:2010 applies to cord switches (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A. This second edition cancels and replaces the first edition published in 1992 and its amendment 1 (1995) and constitutes a technical revision. The main changes from the first edition are as follows:
- Scope, Definitions;
- Protection against electric shock;
- Provision for earthing;
- Construction;
- Fire hazard;
- Abnormal operation and fault conditions for electronic switches;
- Components for electronic switches;
- EMC requirements.
This publication is to be read in conjunction with IEC 61058-1:2000.

IEC 61020-1:2009 provides consistency in detail specifications for electromechanical switches by specifying the terminology, symbols, test methods and other necessary information. Switches covered by this specification:
- are devices which open, close, or change the connection of a circuit by the mechanical motion of conducting parts (contacts);
- have a maximum rated voltage of 480 V;
- have a maximum rated current of 63 A.
This second edition constitutes a technical revision and includes the following significant technical changes with respect to the previous edition:
- The requirements of the IEC 60512 series of standards have been integrated.
- Other necessary information concerning switches as specified in IEC 60512 have been implemented.
The following items have been updated with respect to the first edition:
- test methods were reviewed for detailed description;
- the explanation for the test method of the operating force was rewritten in more detail;
- the test voltage for measurement for contact bounce was reviewed;
- the electrical endurance "ON" duration in the duty cycle was harmonized with IEC 61058;
- the requirements for fire hazards have been deleted;
- testing methods of surface mounting switches based on the Japanese industrial standard were added.

Applies to switches for appliances actuated by hand, by foot or by other human activity for use in, on or with appliances and other equipment for household and similar purposes, with a rated voltage not exceeding 440 V and a rated current not exceeding 63 A. Also covers the indirect actuation of the switch when the function of the actuating member is provided by a part of an appliance or equipment. Replaces IEC 60328 (1972). The contents of the corrigendum of January 2009 have been included in this copy.

Applies to independently mounted switches for appliances actuated by hand, by foot or by other human activity for use with appliances and other equipment for household and similar purposes, with a rated voltage not exceeding 440 V and a rated current not exceeding 63 A.

Specifies the general requirements for impedance measuring relays. Covers test methods and methods of presenting relay characteristics and performance.

This standard includes two types of tests: -the shock test (on energized and non-energized specimen), -the bump test (on non-energized specimen).[
]These requirements are applicable only to measuring relays and protection equipment in a new condition.

Specifies performance requirements for the subfamily as shown in the title. This publication forms part of a series dealing with measuring relays with more than one input energizing quantity and for which IEC 60255-6 gives the general requirements.

Applies to switches for appliances actuated by hand, by foot or by other human activity for use in, on or with appliances and other equipment for household and similar purposes, with a rated voltage not exceeding 440 V and a rated current not exceeding 63 A. Also covers the indirect actuation of the switch when the function of the actuating member is provided by a part of an appliance or equipment. Replaces IEC 60328 (1972).

Contains dimensions and tolerances for spindle ends made to original inch dimensions. The contents of the corrigendum of September 1979 have been included in this copy.

Specifies IEC type designation, dimensions, characteristics (climatic, electrical and mechanical) and test schedules for one, two, three and four-pole centrally bush mounted miniature lever switches for use in electrical and electronic equipment, having a rated voltage not exceeding 250 V and a rated current not exceeding 6 A. The switches covered by this specification are not intended for use as main switches and therefore the requirements of IEC 65 do not apply.

Gives order sheets to be completed when ordering a rotary wafer switch in accordance with IEC 60132-3.

Specifies IEC type designation, construction, dimensions, electrical ratings for 12-position switches. Establishes a schedule for type tests.

Deals with terminology, classification into groups, electrical ratings, marking, IEC type designation, type tests, standard conditions for testing, visual inspection, dimensions, clearances and creepage distances, electrical tests, mechanical tests, climatic tests and endurance tests.