ISO/TC 4/SC 4 - Rolling bearings – Geometrical product specifications (GPS)

ISO 464:2015 specifies the snap ring groove dimensions and tolerance values, chamfer dimensions on the snap ring groove side of the outer ring, and the snap ring dimensions and tolerance values for radial bearings in the dimension series 18 and 19 and the diameter series 0, 2, 3, and 4 (except dimension series 00, 82, and 83), as specified in ISO 15.

ISO 199:2014 specifies dimensional characteristics, limit deviations from nominal values, and tolerance values to define the interface (except chamfers) of thrust rolling bearings. Nominal boundary dimensions are defined in ISO 104.

ISO 492:2014 specifies dimensional and geometrical characteristics, limit deviations from nominal values, and tolerance values to define the interface (except chamfers) of radial rolling bearings. The nominal boundary dimensions are defined in ISO 15, ISO 355 and ISO 8443.

ISO 5753-2:2010 specifies values of axial internal clearance for four-point-contact ball bearings with contact angle of 35°.

ISO 5753-1:2009 specifies values of radial internal clearance for: - radial contact groove ball bearings, except those for insert bearings; - double-row self-aligning ball bearings; - cylindrical roller bearings; - needle roller bearings, except drawn cup needle roller bearings; - toroidal roller bearings; - double-row self-aligning roller bearings. It gives clearance values for all six types of bearing with cylindrical bore and also for double-row self-aligning ball bearings, cylindrical roller bearings, toroidal roller bearings and double-row self-aligning roller bearings with tapered bore.

Cancels and replaces the second edition (1979). Specifies the maximum chamfer dimensions of metric series rolling bearings, for which boundary dimensions, including chamfer minimum dimensions, are given in other International Standards. Gives also requirements for the maximum dimensions of the corresponding shaft and housing filet radii. Does not apply to chamfers, for which dimensions are not specified, or for which other dimensions are specified in other International Standards.

ISO 1224-2:2007 specifies the characteristics that define instrument precision rolling bearings, inch series, their types, boundary dimensions, tolerances and internal clearance, classifications used for selective assembly, torque definitions and test condition, and limitations of bearing yield rates.

ISO 1224-1:2007 specifies the characteristics that define instrument precision rolling bearings, metric series, their types, boundary dimensions, tolerances and internal clearance, classifications used for selective assembly, torque definitions and test condition, and limitations of bearing yield rates.

ISO 199:2005 specifies tolerances for boundary dimensions (except chamfer dimensions) and for the running accuracy of thrust rolling bearings with flat back faces as specified in ISO 104. It is not applicable to certain thrust bearings, e.g. thrust needle roller bearings, or for particular fields of application, e.g. thrust special precision bearings. Chamfer dimension limits are given in ISO 582.

ISO 15242-2:2004 specifies vibration measuring methods for radial single-row and double-row ball bearings, with a contact angle up to and including 45 degrees, under established test conditions. It covers radial ball bearings with cylindrical bore and outside surface, except bearings with filling slots and three- and four-point contact bearings.

ISO 15242-1:2004 defines and specifies measuring methods for vibration of rotating rolling bearings under established test conditions together with calibration of related measuring systems.

ISO 492 specifies tolerances for boundary dimensions (except chamfer dimensions) and the running accuracy of radial rolling bearings specified in ISO 15, ISO 355 and ISO 8443. This International Standard does not apply to certain radial bearings of particular types (e.g., drawn cup needle roller bearings) or for particular fields of application (e.g., airframe bearings and instrument precision bearings).

Cancels and replaces the first edition (1976). Specifies the snap ring groove dimensions, minimum chamfer dimensions on the snap ring groove side of the outer ring and the snap ring dimensions for radial bearings in dimension series 18 and 19 and diameter series 0, 2, 3 and 4 (except dimension series 00, 82 and 83), as specified in ISO 15.

Cancels and replaces the second edition (1986). Specifies tolerances for boundary dimensions and the running accuracy of radial rolling bearings specified in ISO 15 and ISO 355. Does not apply to certain radial bearings of particular type or for particular fields of application.

Specifies clearance values for: radial contact groove ball bearings; double row self-aligning ball bearings; cylindrical roller bearings; needle roller bearings; and double row self-aligning roller bearings. This second edition cancels and replaces the first edition (1981).

Establishes guidelines for measurement of dimensions, running accuracy and internal clearance of both radial and thrust rolling bearings. The purpose is to outline the fundamentals of various measuring and gauging principles which may be used in order to comply with the definitions of ISO 1132 and ISO 5593. The methods described in this Technical Report do differ amongst themselves and there are other adequate measuring and gauging methods. ISO/TR 9274 does not imply any obligation to apply any particular method. However, the methods specified may be referred to in cases of dispute.