2023/826/EU - Commission Regulation (EU) 2023/826 of 17 April 2023 laying down ecodesign requirements for off mode, standby mode, and networked standby energy consumption of electrical and electronic household and office equipment pursuant to Directive 2009/125/EC of the European Parliament and of the Council and repealing Commission Regulations (EC) No 1275/2008 and (EC) No 107/2009

This document specifies methods of measurement of electrical power in networked standby mode and the reporting of the results for edge equipment.
The measurement of power and energy use in non-active mode, other than networked standby mode, is covered by IEC 62301 [1], including the input voltage range.
This document applies to edge equipment that is powered by:
– low voltage mains AC power (LV ≤ 1 000 V AC), or
– an external power supply that provides low voltage (LV ≤ 1 000 V) or extra low voltage (ELV ≤ 50 V) AC or DC power, or
– a separate source of extra low voltage DC power (ELV ≤ 50 V DC), or
– an internal main battery.
Conditions that are outside the scope of this document are as follows:
– active modes (primary function),
– other non-active modes (which are either covered by IEC 62301 [1] or by specific product group standards),
– conditions where main batteries are being charged other than in maintenance mode,
– disconnected condition of the equipment.
This document applies to the following product groups where a networked standby mode is present:
– edge equipment with a network reactivation function, such as household appliances, information technology equipment, audio, video and multimedia systems and equipment,
– digital radio receivers with an emergency warning function,
– gas burning equipment with electrical components.
NOTE 1 The measurements of power, energy use and performance of products during their intended use (when performing their primary functions) are generally specified in product standards and are not covered by this document.
NOTE 2 Networked standby mode for lighting equipment and the measurement of power is specified in IEC 63103 [4].
NOTE 3 Interconnecting equipment (equipment that provides network infrastructure and function) is outside the scope of this document. Measurement of electrical power in networked standby mode for interconnecting equipment is the subject of ETSI standard EN 303 423 [5].
This document also provides a method to test power management and to test whether it is possible to deactivate wireless network connection(s).
NOTE 4 Edge equipment can also include auxiliary batteries.
This group EE publication is primarily intended to be used as an EE standard for the products mentioned in the scope, but is also intended to be used by TCs in the preparation of publications for products which are included in the boundary mentioned in the scope of this document.

This document specifies methods of measurement of electrical power in networked standby mode and the reporting of the results for edge equipment.
The measurement of power and energy use in non-active mode, other than networked standby mode, is covered by IEC 62301 [1], including the input voltage range.
This document applies to edge equipment that is powered by:
– low voltage mains AC power (LV ≤ 1 000 V AC), or
– an external power supply that provides low voltage (LV ≤ 1 000 V) or extra low voltage (ELV ≤ 50 V) AC or DC power, or
– a separate source of extra low voltage DC power (ELV ≤ 50 V DC), or
– an internal main battery.
Conditions that are outside the scope of this document are as follows:
– active modes (primary function),
– other non-active modes (which are either covered by IEC 62301 [1] or by specific product group standards),
– conditions where main batteries are being charged other than in maintenance mode,
– disconnected condition of the equipment.
This document applies to the following product groups where a networked standby mode is present:
– edge equipment with a network reactivation function, such as household appliances, information technology equipment, audio, video and multimedia systems and equipment,
– digital radio receivers with an emergency warning function,
– gas burning equipment with electrical components.
NOTE 1 The measurements of power, energy use and performance of products during their intended use (when performing their primary functions) are generally specified in product standards and are not covered by this document.
NOTE 2 Networked standby mode for lighting equipment and the measurement of power is specified in IEC 63103 [4].
NOTE 3 Interconnecting equipment (equipment that provides network infrastructure and function) is outside the scope of this document. Measurement of electrical power in networked standby mode for interconnecting equipment is the subject of ETSI standard EN 303 423 [5].
This document also provides a method to test power management and to test whether it is possible to deactivate wireless network connection(s).
NOTE 4 Edge equipment can also include auxiliary batteries.
This group EE publication is primarily intended to be used as an EE standard for the products mentioned in the scope, but is also intended to be used by TCs in the preparation of publications for products which are included in the boundary mentioned in the scope of this document.