iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.

25.100.20 - Milling tools

ICS 25.100.20 Details

Milling tools

Fraswerkzeuge

Outils a fraiser

Orodja za frezanje

General Information

Parent
25.100 - Cutting tools

e-Library Subscription

Create subscription and get permanent access to documents within 25.100.20 - Milling tools

Type
Monthly Subscription
for
seat
×
$ 115.53
$ 115.53

Currently subscription includes documents marked with .We are working on making all documents available within the subscription.

Standardization Organization
Technical Committee
Directive
Mandate
50
ISO
ISO 2780:2018(Main)
Milling cutters with tenon drive — Interchangeability dimensions for cutter arbors — Metric series

This document specifies the dimensions for interchangeability between milling cutters with tenon drive and the cutter seating of cutter arbors. It is applicable only to milling cutters of the metric series. It gives the interchangeability dimensions for: — the milling cutters; — the cutter seating on the arbor; — the cutter retaining screw on the cutter arbor.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
SIST
SIST EN 847-2:2018(Main)
Tools for woodworking - Safety requirements - Part 2: Requirements for the shank of shank mounted milling
EN 847-2:2017

This European Standard specifies the determination of the maximum speed for given eccentricity at clamping devices for the shank strength of milling tools with cylindrical and taper shank. It also specifies the marking of the tool. Bore mounted tools which are mounted on an arbor shall be considered as a shank mounted tool.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 847-1:2018(Main)
Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
EN 847-1:2017

This document specifies all hazards arising from the use of tools for woodworking machines, and describes the methods for the elimination or reduction of these hazards by tool design and by the provision of information. This document deals with milling tools (bore mounted, shank mounted), integrated tools and circular saw blades.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
ISO
ISO 10911:2017(Main)
Solid hardmetal end mills with cylindrical shank — Dimensions

ISO 10911:2017 specifies the dimensions of solid hardmetal end mills with cylindrical shank. NOTE For the relationship between designations in this document and the ISO 13399 series, see Annex A.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off
ISO
ISO 12197:2016(Main)
Woodruff keyseat cutters — Dimensions

ISO 12197:2016 specifies the dimensions of milling cutters intended for manufacturing woodruff keyseats in accordance with ISO 3912. Two types of woodruff keyseat cutters with cylindrical shank are specified: - woodruff keyseat cutters with cylindrical shank, in accordance with ISO 3338‑1; - woodruff keyseat cutters with flatted cylindrical shank, in accordance with ISO 3338‑2.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 2584:2016(Main)
Cylindrical cutters with plain bore and key drive — Metric series

ISO 2584:2016 specifies the dimensions of metric series cylindrical cutters with plain bore and key drive, intended for fitting to cutter arbors. It is applicable to solid cutters and also to interlocking cutters. Solid cutters are made either with straight teeth or with helicoidal teeth angled to the right or left; interlocking cutters are always made with straight or helicodial teeth angled to the left and right alternately. The range of outside diameters of these cutters is taken from ISO 523.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 240:2016(Main)
Milling cutters — Interchangeability dimensions for cutter arbors or cutter mandrels

ISO 240:2016 specifies the dimensions for interchangeability between the cutter and the arbor or mandrel, i.e. the diameter of the bore and the arbor or mandrel and elements of the drive, whether by keying or tenon. It applies to all types of milling cutters mounted on cutter arbors or mandrels.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 1641-1:2016(Main)
End mills and slot drills — Part 1: Milling cutters with cylindrical shanks

ISO 1641-1:2016 specifies the general dimensions of the following milling cutters with plain cylindrical, flatted cylindrical and threaded shanks: - end mills, flat-ended or ball-nosed: standard series and long series; - slot drills : short series and standard series. The dimensional characteristics of cylindrical shanks are in accordance with ISO 3338‑1, ISO 3338‑2 and ISO 3338‑3. NOTE These same milling cutters with Morse taper shanks having a tapped hole are dealt with in ISO 1641‑2, those with 7/24 taper shanks in ISO 1641‑3. ISO 1641-1:2016 does not apply to solid hard metal end mills and slot drills.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
ISO
ISO 10145-2:2016(Main)
End mills with brazed helical hardmetal tips — Part 2: Dimensions of end mills with 7/24 taper shank

ISO 10145-2:2016 specifies the general dimensions of end mills with brazed helical hardmetal tips, with 7/24 taper shank. The following two types of end mills with 7/24 taper shank are specified: - end mills with 7/24 taper shank for manual changing; - end mills with 7/24 taper shank for automatic tool changers. ISO 10145-2:2016 applies to right-hand and left-hand end mills, irrespective of helix angle and number of flutes.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 10145-1:2016(Main)
End mills with brazed helical hardmetal tips — Part 1: Dimensions of end mills with parallel shank

ISO 10145-1:2016 specifies the general dimensions of end mills with brazed helical hardmetal tips, with parallel shank. The following two types of end mills with parallel shank are specified: - end mills with plain parallel shank; - end mills with flatted parallel shank. ISO 10145-1:2016 applies to right-hand and left-hand end mills, irrespective of the helix angle and number of flutes.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 6262-1:2013(Main)
End mills with indexable inserts — Part 1: End mills with flatted cylindrical shank

ISO 6262-1:2013 specifies the dimensions of end mills with indexable inserts and flatted parallel shank according to ISO 3338-2.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 6262-2:2013(Main)
End mills with indexable inserts — Part 2: End mills with Morse taper shank

ISO 6262-2:2013 specifies the dimensions of end mills with indexable inserts and Morse taper shank according to ISO 296

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 6986:2013(Main)
Side and face milling (slotting) cutters with indexable inserts — Dimensions

ISO 6986:2013 specifies the dimensions of side and face milling (slotting) cutters with indexable inserts. The shape and dimensions of the inserts are left to the discretion of the manufacturer.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 7755-6:2013(Main)
Hardmetal burrs — Part 6: Arch round- (ball-) nose burrs (style F)

ISO 7755-6:2013 specifies the main dimensions of the cutting part for hardmetal burrs of arch shape, with a round (ball ) nose and designated by the symbol F.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 7755-7:2013(Main)
Hardmetal burrs — Part 7: Arch pointed-nose burrs (style G)

ISO 7755-7:2013 specifies the main dimensions of the cutting part for hardmetal burrs of arch shape, with a pointed nose and designated by the symbol G.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 7755-3:2013(Main)
Hardmetal burrs — Part 3: Cylindrical round- (ball-) nose burrs (style C)

ISO 7755-3:2013 specifies the main dimensions of the cutting part for hardmetal burrs of cylindrical shape, with a round- (ball-) nose and designated by the symbol C. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755‑1.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 7755-4:2013(Main)
Hardmetal burrs — Part 4: Spherical burrs (style D)

ISO 7755-4:2013 specifies the main dimensions of the cutting part for hardmetal burrs of spherical shape and designated by the symbol D.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 7755-8:2013(Main)
Hardmetal burrs — Part 8: Flame burrs (style H)

ISO 7755-8:2013 specifies the main dimensions of the cutting part for hardmetal burrs of flame shape and designated by the symbol H.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 7755-10:2013(Main)
Hardmetal burrs — Part 10: Conical round- (ball-) nose burrs (style L)

ISO 7755-10:2013 specifies the main dimensions of the cutting part for hardmetal burrs of cone shape, with a round (ball ) nose and designated by the Symbol L.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 7755-2:2013(Main)
Hardmetal burrs — Part 2: Cylindrical burrs (style A)

ISO 7755-2:2013 specifies the main dimensions of the cutting part for hardmetal burrs of cylindrical shape and designated by the symbol A. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 7755-12:2013(Main)
Hardmetal burrs — Part 12: Inverted cone burrs (style N)

ISO 7755-12:2013 specifies the main dimensions of the cutting part for hardmetal burrs of inverted cone shape and designated by the symbol N.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 7755-11:2013(Main)
Hardmetal burrs — Part 11: Conical pointed-nose burrs (style M)

ISO 7755-11:2013 specifies the main dimensions of the cutting part for hardmetal burrs of cone shape, with a pointed nose and designated by the symbol M.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 7755-9:2013(Main)
Hardmetal burrs — Part 9: 60 degrees and 90 degrees cone burrs (styles J and K)

ISO 7755-9:2013 the main dimensions of the cutting part for hardmetal burrs of 60° cone and 90° cone shape and designated by the symbols J and K.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 7755-5:2013(Main)
Hardmetal burrs — Part 5: Oval burrs (style E)

ISO 7755-5:2013 specifies the main dimensions of the cutting part for hardmetal burrs of oval shape and designated by the symbol E.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 7755-1:2013(Main)
Hardmetal burrs — Part 1: General specifications

ISO 7755-1:2013 specifies the common characteristics of hardmetal burrs of various styles, in solid design or with brazed shank.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
  • Standard
    12 pages
    Russian language
    sale 15% off
  • Standard
    7 pages
    Russian language
    sale 15% off
ISO
ISO 3338-2:2013(Main)
Cylindrical shanks for milling cutters — Part 2: Dimensional characteristics of flatted cylindrical shanks

ISO 3338-2:2013 specifies the dimensions of flatted cylindrical shanks for milling cutters, of diameters 6 mm to 20 mm for single-flatted shanks, of 25 mm to 63 mm for double-flatted shanks and of 6 mm to 32 mm for shank with inclined clamping surface. In the case of single-flatted shanks, it is applicable to both single-ended cutters and double-ended cutters, as double-flatted shanks cannot admit single-ended cutters. The dimensions of plain cylindrical shanks and threaded shanks are given in ISO 3338-1 and ISO 3338-3, respectively. The two shank types covered by ISO 3338-1 and ISO 3338-2:2013 have the same dimensional characteristics (diameters and lengths), but different tolerances on diameters.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
ISO
ISO 11529:2013(Main)
Milling cutters — Designation — Shank-type and bore-type milling cutters of solid or tipped design or with indexable cutting edges

ISO 11529:2013 establishes a designation system for shank-type and bore-type milling cutters of either solid or tipped design or with indexable cutting edges with the purpose of simplifying communication between the users and suppliers of such tools.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    14 pages
    French language
    sale 15% off
  • Standard
    14 pages
    French language
    sale 15% off
ISO
ISO 15917:2012(Main)
Solid ball-nosed end mills with cylindrical shanks, made of carbide and ceramic materials

ISO 15917:2012 specifies types and dimensions of solid ball-nosed end mills with cylindrical shanks made of carbide and ceramic materials according to ISO 513.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
ISO
ISO 1641-2:2011(Main)
End mills and slot drills — Part 2: Dimensions and designation of milling cutters with Morse taper shanks

ISO 1641-2:2011 specifies the general dimensions and designation of the following milling cutters with Morse taper and having a tapped hole: - end mills, flat-ended or ball-nosed - standard series and long series; - slot drills - short series and standard series. Morse taper shanks are in accordance with ISO 296 and ISO 5413.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
ISO
ISO 1641-3:2011(Main)
End mills and slot drills — Part 3: Dimensions and designation of milling cutters with 7/24 taper shanks

ISO 1641-3:2011 specifies the general dimensions and designation of the following milling cutters with 7/24 taper shanks: - end mills, flat-ended or ball-nosed - normal series and long series (manual changers); - slot drills - short series and normal series (manual changers); - end mills, flat-ended - normal series and long series (automatic changers). Tool shanks with 7/24 taper for manual tool changers are in accordance with ISO 297. Tool shanks with 7/24 taper for automatic tool changers are in accordance with ISO 7388-1 and ISO 7388-2.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
ISO
ISO 6462:2011(Main)
Face and shoulder milling cutters with indexable inserts — Dimensions

ISO 6462:2011 specifies the dimensions of face milling cutters with indexable inserts.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off
ISO
ISO 3860:2011(Main)
Bore cutters with key drive — Form milling cutters with constant profile

ISO 3860:2011 specifies the dimensions of bore form milling cutters with a constant profile with key drive. It deals with the following three types of bore cutters with key drive: convex milling cutters; concave milling cutters; corner-rounding cutters.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 22037:2007(Main)
Solid end mills with corner radii and cylindrical shanks made of hard cutting materials — Dimensions

ISO 22037:2007 specifies types and dimensions of solid end mills, with corner radii and cylindrical shanks, made of hard cutting materials in accordance with ISO 513.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off
CEN
EN ISO 15641:2001(Main)
Milling cutters for high speed machining - Safety requirements (ISO 15641:2001)
SIST EN ISO 15641:2002

This standard deals with the principle hazards arising from use of milling cutters, e.g. milling cutters according to ISO 3855, used for high speed machining (chip removal machining at increased peripheral speeds) on metal working machine tools and prescribes safety requirements.
It specifies design methods, centrifugal force test procedures, operational limits and the provision of information that will lead to minimisation or elimination of these hazards.
The standard is applicable to milling cutters which are intended for operation at speeds in accordance with figures 1 and 2.
These figures respectively define the rotational speed limits and peripheral speed limits for specific cutter diameters.
NOTE  A detailed explanation is provided in annex B.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 15641:2002(Main)
Milling cutters for high speed machining - Safety requirements (ISO 15641:2001)
EN ISO 15641:2001

This standard deals with the principle hazards arising from use of milling cutters, e.g. milling cutters according to ISO 3855, used for high speed machining (chip removal machining at increased peripheral speeds) on metal working machine tools and prescribes safety requirements.
It specifies design methods, centrifugal force test procedures, operational limits and the provision of information that will lead to minimisation or elimination of these hazards.
The standard is applicable to milling cutters which are intended for operation at speeds in accordance with figures 1 and 2.
These figures respectively define the rotational speed limits and peripheral speed limits for specific cutter diameters.
NOTE  A detailed explanation is provided in annex B.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
ISO
ISO 15641:2001(Main)
Milling cutters for high speed machining — Safety requirements
  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    14 pages
    French language
    sale 15% off
ISO
ISO 3859:2000(Main)
Inverse dovetail cutters and dovetail cutters with cylindrical shanks

This International Standard specifies the dimensions of inverse dovetail cutters and dovetail cutters with plain cylindrical shanks, flatted cylindrical shanks and threaded shanks. Inverse dovetail cutters and dovetail cutters have the same design characteristics. This International Standard applies to 45° and 60° dovetail cutters and inverse dovetail cutters with diameters of d2 between 16 mm and 31,5 mm.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
ISO
ISO 3337:2000(Main)
T-slot cutters with cylindrical shanks and with Morse taper shanks having tapped hole

This International Standard specifies the dimensions of T-slot cutters with plain or flatted cylindrical shanks, with threaded shanks and with Morse taper shanks having tapped hole. It applies to those tools which are intended for manufacturing T-slots for machine tools for equipment, in accordance with ISO 299. T-slot cutters with plain cylindrical shanks or flatted cylindrical shanks and with threaded shanks are suitable for the production of slots in accordance with ISO 299 from 5 mm to 36 mm inclusive; those with Morse taper shanks are suitable for the production of slots in accordance with ISO 299 from 10 mm to 54 mm inclusive.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
SIST
SIST ISO 2940-2:1998(Main)
Milling cutters mounted on centring arbors having a 7/24 taper -- Inserted tooth cutters
ISO 2940-2:1974

These cutters are equipped either with high speed steel inserted teeth or with inserted teeth with brazed carbide tips. Concerns milling cutters, arbor located, to be used with a well-defined spindle nose having a 7/24 taper and milling cutter, arbor located, to be used with both spindle nose No. 50 and spindle nose No. 60 having a 7/24 taper. Dimensions for centring arbors and fitting dimensions for fixation are given in ISO 2940-1.

  • Standard
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
SIST
SIST ISO 2940-1:1998(Main)
Milling cutters mounted on centring arbors having a 7/24 taper -- Fitting dimensions -- Centring arbors
ISO 2940-1:1974

Applies both to cutters with inserted teeth, made from high speed steel or with brazed carbide tips, and to cutters equipped with indexable carbide tips. Concerns milling cutters, arbor located, to be used with a well-defined spindle nose having a 7/24 taper and milling cutter, arbor located, to be used bith spindle nose No. 50 and spindle nose No. 60 having a 7/24 taper. The general fitting dimensions are in accordance with ISO 297.

  • Standard
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 3338-1:1996(Main)
Cylindrical shanks for milling cutters — Part 1: Dimensional characteristics of plain cylindrical shanks

Specifies the dimensions of plain cylindrical shanks for milling cutters with a diameter of 3 mm to 63 mm.

  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
ISO
ISO 3338-3:1996(Main)
Cylindrical shanks for milling cutters — Part 3: Dimensional characteristics of threaded shanks

Specifies the dimensions of threaded shanks for milling cutters with a diameter of 6 mm to 32 mm.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
ISO
ISO 8688-1:1989(Main)
Tool life testing in milling — Part 1: Face milling

Specifies recommended procedures for tool-life testing with cemented carbide tools used for face milling of steel and cast iron workpieces. Can be applied to laboratory as well as to production practice. Considers conditions as a result of which tool deterioration is due to wear. Establishes specifications for workpiece, tool, cutting fluid, cutting conditions, equipment, assessment of tool deterioration and tool life, test procedures, recording, evaluation and presentation of results.

  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    27 pages
    French language
    sale 15% off
  • Standard
    27 pages
    French language
    sale 15% off
  • Standard
    27 pages
    French language
    sale 15% off
  • Standard
    27 pages
    French language
    sale 15% off
ISO
ISO 8688-2:1989(Main)
Tool life testing in milling — Part 2: End milling

specifies recommended procedures for tool-life testing with high-speed steel tools used for end milling of steel and cast iron workpieces. Can be applied to laboratory as well as to production practice. Considers conditions under which tool deterioration is mainly due to wear. Establishes specifications for workpiece, tool, cutting fluid, cutting conditions, equipment, assessment of tool deterioration and tool life, test procedures, recording, evaluation and presentation of results.

  • Standard
    26 pages
    English language
    sale 15% off
  • Standard
    26 pages
    English language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off
ISO
ISO 2586:1985(Main)
Shell end mills with plain bore and tenon drive — Metric series
  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
ISO
ISO 3855:1977(Main)
Milling cutters — Nomenclature
  • Standard
    18 pages
    English language
    sale 15% off
ISO
ISO 3940:1977(Main)
Tapered die-sinking cutters with parallel shanks

Lays down the diemnsions of these cutters with plain parallel or parallel flatted shanks. The cutters are particular intended for directly obtained clearances of moulds, patterns and dies, when these exceed 2 52'. Applies to flat-end cutters and ball-nosed cutters. There are short type, medium type, and long type cutters.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 2940-2:1974(Main)
Milling cutters mounted on centring arbors having a 7/24 taper — Inserted tooth cutters
SIST ISO 2940-2:1998

These cutters are equipped either with high speed steel inserted teeth or with inserted teeth with brazed carbide tips. Concerns milling cutters, arbor located, to be used with a well-defined spindle nose having a 7/24 taper and milling cutter, arbor located, to be used with both spindle nose No. 50 and spindle nose No. 60 having a 7/24 taper. Dimensions for centring arbors and fitting dimensions for fixation are given in ISO 2940-1.

  • Standard
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 2940-1:1974(Main)
Milling cutters mounted on centring arbors having a 7/24 taper — Fitting dimensions — Centring arbors
SIST ISO 2940-1:1998

Applies both to cutters with inserted teeth, made from high speed steel or with brazed carbide tips, and to cutters equipped with indexable carbide tips. Concerns milling cutters, arbor located, to be used with a well-defined spindle nose having a 7/24 taper and milling cutter, arbor located, to be used bith spindle nose No. 50 and spindle nose No. 60 having a 7/24 taper. The general fitting dimensions are in accordance with ISO 297.

  • Standard
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 2585:1972(Main)
Slotting cutters with plain bore and key drive — Metric series

Specifies the dimensions of slotting cutters with straigth-sided teeth and with helical teeth. The range of outside diameters is taken from ISO 523.

  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
50