77.140.20 - Stainless steels

This document specifies requirements and their test methods for stainless steels used in
dental instruments.
It is applicable to single-use and reusable instruments, regardless of whether they are connected to a
power-driven system or not.
It contains a current selection of stainless steels suitable for use in the manufacture of dental
instruments.

ISO 13520:2015 specifies procedures which are covered for estimating ferrite content in certain grades of austenitic iron-chromium-nickel alloy castings that have compositions balanced to create the formation of ferrite as a second phase in amounts controlled within specified limits. Methods are described for estimating ferrite content by chemical, magnetic and metallographic means.

This document applies to corrosion resistant steel castings for general purposes.
This document relates to castings manufactured from martensitic, austenitic, fully austenitic and
austenitic-ferritic steel grades characterized by their chemical composition (see Table 1) and mechanical properties (see Table 2).
ln cases where castings are joined by welding by the founder, this document applies.
ln cases where castings are welded
-   to wrought products (plates, tubes, forgings),
-   or by non-...view more

This document applies to corrosion resistant steel castings for general purposes.
This document relates to castings manufactured from martensitic, austenitic, fully austenitic and
austenitic-ferritic steel grades characterized by their chemical composition (see Table 1) and mechanical properties (see Table 2).
ln cases where castings are joined by welding by the founder, this document applies.
ln cases where castings are welded:
- to wrought products (plates, tubes, forgings);
- or by non...view more

This document specifies the technical delivery requirements for
— semi-finished products, hot formed, e.g. blooms, billets, slabs (see NOTE 1),
— bars (see NOTE 1),
— wire rod,
— finished flat products, and
— hammer or drop forgings (see NOTE 1)
manufactured from the case-hardening non-alloy or alloy steels listed in Table 3 and supplied in one
of the heat-treatment conditions given for the different types of products in Table 1 and in one of the
surface conditions given in Table 2.
The...view more

This document specifies the technical delivery requirements for
— semi-finished products, hot formed, e.g. blooms, billets, slabs (see NOTE 1),
— bars (see NOTE 1),
— wire rod,
— finished flat products, and
— hammer or drop forgings (see NOTE 1)
manufactured from the case-hardening non-alloy or alloy steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the surface conditions given in Table 2.
The s...view more

This European Standard gives general recommendations for the fusion welding of stainless steels. Specific details relevant to austenitic, austenitic-ferritic, ferritic and martensitic stainless are given in annexes A to D.

This document specifies the technical delivery requirements for — semi-finished products, hot formed, e.g. blooms, billets, slabs (see NOTE 1), — bars (see NOTE 1), — wire rod, — finished flat products, and — hammer or drop forgings (see NOTE 1) manufactured from the case-hardening non-alloy or alloy steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the surface conditions given in Table 2. The steels a...view more

ISO 683-1:2016 specifies the technical delivery requirements for
- semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
- bars (see Note 1),
- wire rod,
- finished flat products, and
- hammer or drop forgings (see Note 1)
manufactured from the direct hardening non-alloy steels and the non-alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one ...view more

ISO 683-4:2016 gives the technical delivery requirements for semi-finished products (e.g. blooms, billets, slabs), bars and wire rod, manufactured from the free-cutting steels listed in Table 2 and supplied in one of the treatment conditions given for the different types of products in Table 1, rows 2 to 4.
It covers three groups of free-cutting steels for mechanical purposes as listed in Table 2, namely
a) not intended for heat treatment,
b) suitable for case-hardening, and
c) suitable for ...view more

ISO 683-2:2016 specifies the technical delivery requirements for
- semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
- bars (see Note 1),
- wire rod,
finished flat products, and
- hammer or drop forgings (see Note 1)
manufactured from the direct hardening alloy steels and the alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the sur...view more

This document specifies a potentiometric or visual titration method for the determination of manganese content in alloyed steels. The method is applicable to manganese mass fractions between 2 % and 25 %. Vanadium and cerium interfere with the determination. If the mass fraction of cerium in the sample is less than 0,01 %, or the mass fraction of vanadium in the sample is less than 0,005 %, the interference is negligible, otherwise theoretical corrections are necessary.

This document specifies technical delivery requirements for the surface quality of round bars, squares, hexagons and wire rod in the hot rolled condition with nominal dimensions dN from 5 mm to 200 mm. This document is applicable to bright products and tool steels, if agreed at the time of enquiry and order between manufacturer and purchaser.
By agreement between manufacturer and purchaser, this document can also be applied to other special profiles.
This document is particularly applicable to...view more

This document specifies requirements for the following grades of wrought tool steels:
a) non-alloy cold-work tool steels;
b) alloy cold-work tool steels;
c) alloy hot-work tool steels;
d) high-speed tool steels.
If not stated otherwise, this document applies to all types of hot-rolled, forged, cold-drawn or cold-rolled products or products produced by powder metallurgy, which are supplied in one of the surface and heat-treatment conditions given in 6.2 and Table 1.
NOTE Tables 2, 4, 6 and ...view more

This document specifies requirements for non-alloy and alloy steels that are intended for cold heading or cold extruding and are delivered as wire rods, wire or bars. It also contains specific requirements for: — steels not intended for heat treatment, with diameters from 2 mm to 100 mm (see Annex A); — case-hardening steels with diameters from 2 mm to 100 mm (see Annex B); — steels for quenching and tempering, including boron alloyed steels (see Table C.3), with diameters from 2 mm to 100 mm (s...view more

ISO 683-4:2016 gives the technical delivery requirements for semi-finished products (e.g. blooms, billets, slabs), bars and wire rod, manufactured from the free-cutting steels listed in Table 2 and supplied in one of the treatment conditions given for the different types of products in Table 1, rows 2 to 4.
It covers three groups of free-cutting steels for mechanical purposes as listed in Table 2, namely
a) not intended for heat treatment,
b) suitable for case-hardening, and
c) suitable for ...view more

ISO 683-2:2016 specifies the technical delivery requirements for
- semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
- bars (see Note 1),
- wire rod,
finished flat products, and
- hammer or drop forgings (see Note 1)
manufactured from the direct hardening alloy steels and the alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the sur...view more

ISO 683-1:2016 specifies the technical delivery requirements for
- semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
- bars (see Note 1),
- wire rod,
- finished flat products, and
- hammer or drop forgings (see Note 1)
manufactured from the direct hardening non-alloy steels and the non-alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one ...view more

This document specifies technical delivery requirements for the surface quality of round bars, squares, hexagons and wire rod in the hot rolled condition with nominal dimensions dN from 5 mm to 200 mm. This document is applicable to bright products and tool steels, if agreed at the time of enquiry and order between manufacturer and purchaser. By agreement between manufacturer and purchaser, this document can also be applied to other special profiles. This document is particularly applicable to s...view more

1.1   This Part of EN 10263 is applicable to round rod, round bars and wire made of stainless steels intended for cold heading and cold extrusion having a diameter up to and including:
   25 mm for ferritic and austenitic-ferritic steels;
   50 mm for austenitic steels;
   100 mm for martensitic steels
1.2   prEN 10263-1:2013 is indispensable for the application of this part of EN 10263.