EN ISO 9443:2018
(Main)Surface quality classes for hot-rolled bars and wire rod (ISO 9443:2018)
Surface quality classes for hot-rolled bars and wire rod (ISO 9443:2018)
This document specifies technical delivery requirements for the surface quality of round bars, squares, hexagons and wire rod in the hot rolled condition with nominal dimensions dN from 5 mm to 200 mm. This document is applicable to bright products and tool steels, if agreed at the time of enquiry and order between manufacturer and purchaser.
By agreement between manufacturer and purchaser, this document can also be applied to other special profiles.
This document is particularly applicable to steels for engineering and structural applications.
This document does not include any requirements for the permissible depth of surface decarburization.
NOTE The determination of depth of surface decarburization is presented in ISO 3887.
The material standards for steel bars and wire rod can exclude the application of one or other of the surface quality classes of this document. They can also cover requirements for surface quality which deviate from this document. In these cases the requirements of the material standard prevail.
Oberflächengüteklassen für warmgewalzten Stabstahl und Walzdraht (ISO 9443:2018)
Dieses Dokument enthält die technischen Lieferbedingungen für die Oberflächengüteklassen für Rundstäbe, Vierkantstäbe, Sechskantstäbe und Walzdraht im warmgewalzten Zustand mit Nenndurchmessern dN von 5 mm bis 200 mm. Dieses Dokument kann auch für Blankstahl und Werkzeugstahl herangezogen werden, sofern dies zum Zeitpunkt der Anfrage und Bestellung zwischen Hersteller und Besteller vereinbart war.
Nach Vereinbarung zwischen Hersteller und Besteller kann dieses Dokument auf andere Sonderprofilformen angewendet werden.
Dieses Dokument gilt vor allem für Stähle, die im Maschinenbau und im Bauwesen angewendet werden.
Dieses Dokument enthält keine Anforderungen an die zulässige Tiefe der Randentkohlung.
ANMERKUNG Die Bestimmung der Tiefe der Randentkohlung ist in ISO 3887 beschrieben.
Die Normen für die Lieferbedingungen für Stabstahl und Walzdraht können die Anwendung einzelner Oberflächengüteklassen dieses Dokumentes ausschließen. Dies können ebenfalls Anforderungen an die Oberflächenqualität sein, die von diesem Dokument abweichen. In diesen Fällen gelten die Anforderungen in den Normen für die Lieferbedingungen.
Classes de qualité de surface des barres et fils-machine laminés à chaud (ISO 9443:2018)
Le présent document spécifie les spécifications techniques de livraison relatives à la qualité de surface des barres de section ronde, carrée, hexagonale et du fil machine en acier laminé à chaud avec des dimensions nominales dN compris entre 5 mm et 200 mm. Le présent document est applicable aux produits transformés à froid et aux aciers à outils, si cela est convenu au moment de l'appel d'offres et de la commande entre le fabricant et l'acheteur.
Par accord entre le fabricant et l'acheteur, le présent document peut également être appliquée à d'autres profilés spéciaux.
Le présent document est plus particulièrement applicable aux aciers à usages mécaniques, et aux aciers de construction.
Le présent document ne renferme aucune spécification relative à la profondeur admissible de décarburation.
NOTE La détermination de la profondeur de décarburation est décrite dans l'ISO 3887.
Les normes de matériaux pour barres et fil machine en acier peuvent exclure l'utilisation de l'une quelconque des classes de qualité de surface prévues dans le présent document. Elles peuvent également renfermer des spécifications pour la qualité de surface divergentes par rapport à ce présent document. Dans ce cas, les spécifications de la norme de matériau prévalent.
Kakovostni razredi površin vroče valjanih drogov in valjane žice (ISO 9443:2018)
Ta mednarodni standard določa tehnične dobavne zahteve za kakovost površin okroglih, kvadratnih in šesterokotnih drogov ter valjane žice v vroče valjanem stanju z nazivnimi premeri dN od 5 mm do 200 mm. Na podlagi dogovora med proizvajalcem in kupcem se ta mednarodni standard lahko uporablja tudi za druge posebne profile. Ta mednarodni standard se uporablja zlasti za jekla, namenjena za gradbeno in konstrukcijsko uporabo, po dogovoru pa se lahko uporablja tudi za orodna jekla.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 9443:2018
01-oktober-2018
1DGRPHãþD
SIST EN 10221:1998
.DNRYRVWQLUD]UHGLSRYUãLQYURþHYDOMDQLKGURJRYLQYDOMDQHåLFH ,62
Surface quality classes for hot-rolled bars and wire rod (ISO 9443:2018)
Oberflächengüteklassen für warmgewalzten Stabstahl und Walzdraht (ISO 9443:2018)
Classes de qualité de surface des barres et fils-machine laminés à chaud (ISO
9443:2018)
Ta slovenski standard je istoveten z: EN ISO 9443:2018
ICS:
77.140.60 Jeklene palice in drogovi Steel bars and rods
SIST EN ISO 9443:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9443:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 9443:2018
EN ISO 9443
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2018
EUROPÄISCHE NORM
ICS 77.140.20; 77.140.60; 77.140.10 Supersedes EN 10221:1995
English Version
Surface quality classes for hot-rolled bars and wire rod
(ISO 9443:2018)
Classes de qualité de surface des barres et fils-machine Oberflächengüteklassen für warmgewalzten Stabstahl
laminés à chaud (ISO 9443:2018) und Walzdraht (ISO 9443:2018)
This European Standard was approved by CEN on 23 May 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9443:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9443:2018
EN ISO 9443:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 9443:2018
EN ISO 9443:2018 (E)
European foreword
This document (EN ISO 9443:2018) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 105 “Steels for heat treatment, alloy steels, free-
cutting steels and stainless steels” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2019, and conflicting national standards shall
be withdrawn at the latest by January 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10221:1995.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9443:2018 has been approved by CEN as EN ISO 9443:2018 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 9443:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 9443:2018
INTERNATIONAL ISO
STANDARD 9443
Second edition
2018-05
Surface quality classes for hot-rolled
bars and wire rod
Classes de qualité de surface des barres et fils-machine laminés à chaud
Reference number
ISO 9443:2018(E)
©
ISO 2018
---------------------- Page: 7
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.