iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D1500-02

(Test Method)

Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)

Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)

SCOPE
1.1 This test method covers the visual determination of the color of a wide variety of petroleum products such as lubricating oils, heating oils, diesel fuel oils, and petroleum waxes.
Note 1—Test Method D 156 is applicable to refined products that have an ASTM color lighter than 0.5. IP Method 17 includes a procedure for measuring the color of undyed, refined products such as gasoline, white spirit, and kerosine by comparison with a series of IP Standard glasses. It also includes a procedure by which petroleum products, except black oils and bitumens, may be measured for tint and depth of color in terms of Lovibond units by a series of red, yellow, and blue glasses.
1.2 This test method reports results specific to the test method and recorded as "ASTM Color."
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Nov-2002
ICS
17.180.20 - Colours and measurement of light
75.080 - Petroleum products in general
Technical Committee
D02 - Petroleum Products, Liquid Fuels, and Lubricants
Drafting Committee
D02.05 - Properties of Fuels, Petroleum Coke and Carbon Material
Current Stage
Ref Project

Relations

Replaces
ASTM D1500-98 - Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)
Effective Date
10-Nov-2002
Replaced By
ASTM D1500-03 - Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)
Effective Date
01-Nov-2003
Referred By
ASTM D8128-22 - Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings
Effective Date
10-Nov-2002
Referred By
ASTM D4732-13(2020) - Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable
Effective Date
10-Nov-2002
Referred By
ASTM D7665-22 - Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids
Effective Date
10-Nov-2002
Referred By
ASTM D4731-13(2020) - Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable
Effective Date
10-Nov-2002
Referred By
ASTM E805-22 - Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials
Effective Date
10-Nov-2002
Referred By
ASTM D8180-23 - Standard Specification for Rerefined Mineral Insulating Liquid Used in Electrical Apparatus
Effective Date
10-Nov-2002
Referred By
ASTM D1218-21 - Standard Test Method for Refractive Index and Refractive Dispersion of Hydrocarbon Liquids
Effective Date
10-Nov-2002
Referred By
ASTM D8506-23 - Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems
Effective Date
10-Nov-2002
Referred By
ASTM D6468-22 - Standard Test Method for High Temperature Stability of Middle Distillate Fuels
Effective Date
10-Nov-2002
Referred By
ASTM D1747-09(2019) - Standard Test Method for Refractive Index of Viscous Materials
Effective Date
10-Nov-2002
Referred By
ASTM D1364-22 - Standard Test Method for Water in Volatile Solvents (Karl Fischer Reagent Titration Method)
Effective Date
10-Nov-2002
Referred By
ASTM D3455-11(2019) - Standard Test Methods for Compatibility of Construction Material with Electrical Insulating Oil of Petroleum Origin
Effective Date
10-Nov-2002
Referred By
ASTM D7973-19 - Standard Guide for Monitoring Failure Mode Progression in Plain Bearings
Effective Date
10-Nov-2002

Buy Standard

ASTM D1500-02 - Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)ASTM D1500-02 - Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)
PreviousNext
Standard
ASTM D1500-02 - Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: D 1500 – 02
Designation: 196/97
Standard Test Method for
1
ASTM Color of Petroleum Products (ASTM Color Scale)
This standard is issued under the fixed designation D 1500; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D 2500 Test Method for Cloud Point of Petroleum Prod-
3
ucts
1.1 This test method covers the visual determination of the
D 4057 Practice for Manual Sampling of Petroleum and
color of a wide variety of petroleum products such as lubricat-
4
Petroleum Products
ing oils, heating oils, diesel fuel oils, and petroleum waxes.
2.2 IP Standard:
NOTE 1—Test Method D 156 is applicable to refined products that have 5
IP 17 Color by the Lovibond Tintometer
an ASTM color lighter than 0.5. IP Method 17 includes a procedure for
measuring the color of undyed, refined products such as gasoline, white
3. Summary of Test Method
spirit, and kerosine by comparison with a series of IP Standard glasses. It
3.1 Using a standard light source, a liquid sample is placed
also includes a procedure by which petroleum products, except black oils
in the test container and compared with colored glass disks
and bitumens, may be measured for tint and depth of color in terms of
Lovibond units by a series of red, yellow, and blue glasses. ranging in value from 0.5 to 8.0. When an exact match is not
found and the sample color falls between two standard colors,
1.2 This test method reports results specific to the test
the higher of the two colors is reported.
method and recorded as “ASTM Color.”
1.3 This standard does not purport to address all of the
4. Significance and Use
safety concerns, if any, associated with its use. It is the
4.1 Determination of the color of petroleum products is used
responsibility of the user of this standard to establish appro-
mainly for manufacturing control purposes and is an important
priate safety and health practices and determine the applica-
quality characteristic since color is readily observed by the user
bility of regulatory limitations prior to use.
of the product. In some cases the color may serve as an
2. Referenced Documents indication of the degree of refinement of the material. When the
color range of a particular product is known, a variation outside
2.1 ASTM Standards:
the established range may indicate possible contamination with
D 155 Test Method for Color of Lubricating Oil and Petro-
2 another product. However, color is not always a reliable guide
latum by Means of ASTM Union Colorimeter
to product quality and should not be used indiscriminately in
D 156 Test Method for Saybolt Color of Petroleum Prod-
3 product specifications.
ucts (Saybolt Chromometer Method)
D 938 Test Method for Congealing Point of Petroleum
5. Apparatus
3
Waxes, Including Petrolatum
5.1 Colorimeter, consisting of light source, glass color
standards, sample container housing with cover, and viewing
piece as listed in Annex A1.
1
This test method is under the jurisdiction of ASTM Committee D02 on
5.2 Sample Container—For referee work, use the glass
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
sample jar as shown in Fig. 1. For routine tests, it is permissible
D02.05.0C on Color and Reactivity Color and Reactivity.
Current edition approved Nov. 10, 2002. Published January 2003. Originally to use a cylindrical, clear glass jar with a flat bottom of 30 to
approved in 1957. Last previous edition approved in 1998 as D 1500–98.
32.4 mm internal diameter and 115 to 125 mm in external
This is also a standard of the Institute of Petroleum issued under the fixed
height and a wall thickness no greater than 1.6 mm as specified
designation IP 196. The final number indicates the year of last revision. This test
method was adopted as a joint ASTM-IP standard in 1966. In the IP, this test method
is under the jurisdiction of the Standardization Committee.
2 4
1958 Book of ASTM Standards, Part 7; see also the compilation of “ASTM Annual Book of ASTM Standards, Vol 05.02.
5
Standards on Petroleum Products and Lubricants,” October 1959, p. 91. “Methods for Analysis and Testing,” available from Institute of Petroleum (IP),
3
Annual Book of ASTM Standards, Vol 05.01. 61 New Cavendish St., London, WIG 7AR, U.K.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new vers
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D1500-12(2017)(Test Method)
Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)

SIGNIFICANCE AND USE
4.1 Determination of the color of petroleum products is used mainly for manufacturing control purposes and is an important quality characteristic, since color is readily observed by the user of the product. In some cases, the color may serve as an indication of the degree of refinement of the material. When the color range of a particular product is known, a variation outside the established range may indicate possible contamination with another product. However, color is not always a reliable guide to product quality and should not be used indiscriminately in product specifications.
SCOPE
1.1 This test method covers the visual determination of the color of a wide variety of petroleum products, such as lubricating oils, heating oils, diesel fuel oils, and petroleum waxes.  
Note 1: Test Method D156 is applicable to refined products that have an ASTM color lighter than 0.5.  
1.2 This test method reports results specific to the test method and recorded as “ASTM Color.”  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D1500-12(2017)(Test Method)
Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)

SIGNIFICANCE AND USE
4.1 Determination of the color of petroleum products is used mainly for manufacturing control purposes and is an important quality characteristic, since color is readily observed by the user of the product. In some cases, the color may serve as an indication of the degree of refinement of the material. When the color range of a particular product is known, a variation outside the established range may indicate possible contamination with another product. However, color is not always a reliable guide to product quality and should not be used indiscriminately in product specifications.
SCOPE
1.1 This test method covers the visual determination of the color of a wide variety of petroleum products, such as lubricating oils, heating oils, diesel fuel oils, and petroleum waxes.  
Note 1: Test Method D156 is applicable to refined products that have an ASTM color lighter than 0.5.  
1.2 This test method reports results specific to the test method and recorded as “ASTM Color.”  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM B472-23(Specification)
Standard Specification for Nickel Alloy Billets and Bars for Reforging

ABSTRACT
This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556 nickel alloy billets and bars for reforging. The products shall be hot worked from ingots by rolling, forging, extruding, hammering, or pressing. The material shall conform to the chemical composition requirements prescribed by the reference material. The chemical composition of the material shall be determined by chemical analysis in accordance with test method E1473.
SCOPE
1.1 This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N10362, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, UNS N06699, and UNS R305562 billets and bars for reforging.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off