iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E313-10

(Practice)

Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates

Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates

SIGNIFICANCE AND USE
This practice should be used only to compare specimens of the same material and same general appearance. For example, a series of specimens to be compared should have generally similar gloss, texture, and (if not opaque) thickness, and translucency.
For yellowness measurement, this practice is limited to specimens having dominant wavelength in the range 570 to 580 nm, or Munsell hue approximately 2.5GY to 2.5 Y. For whiteness measurement, this practice is limited to specimens having Munsell value greater than 8.3 (CIE Y greater than 65) and Munsell chroma no greater than 0.5 for B hues, 0.8 for Y hues, and 0.3 for all other hues (see 3.3.1).
The combination of measurement and calculation leading to indices of yellowness or whiteness is a psychophysical process, that is, the procedures specified are designed to provide numbers correlating with visual estimates made under specified typical observing conditions. Because visual observing conditions can vary widely, users should compare calculated indices with visual estimates to ensure applicability. Some standards addressing the visual estimation of color and color difference are Practices D1535, D1729, E1360, and E1541, and Guide E1499.
This practice does not cover the preparation of specimens, a procedure that may affect significantly the quantities measured. In general, specimens should be prepared and presented for measurement in the manner that is standard for the test being performed. Select enough specimens or specimen areas to provide an average result that is representative of each sample to be tested. See Practice E1345.
SCOPE
1.1 This practice provides numbers that correlate with visual ratings of yellowness or whiteness of white and near-white or colorless object-color specimens, viewed in daylight by an observer with normal color vision. White textiles, paints, and plastics are a few of the materials that can be described by the indices of yellowness or whiteness calculated by this practice.
1.2 For a complete analysis of object colors, by a specified observer and under a specified illuminant, use of three parameters is required. For near-white specimens, however, it is often useful to calculate single-number scales of yellowness or whiteness. This practice provides recommended equations for such scales and discusses their derivations and uses, and limits to their applicability (see also Ref (1) ).
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Jun-2010
ICS
17.180.20 - Colours and measurement of light
Technical Committee
E12 - Color and Appearance
Drafting Committee
E12.04 - Color and Appearance Analysis
Current Stage
Ref Project

Relations

Replaces
ASTM E313-05 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
Effective Date
01-Jul-2010
Replaced By
ASTM E313-15 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
Effective Date
01-Jan-2015
Referred By
ASTM G178-16(2023) - Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique
Effective Date
01-Jul-2010
Referred By
ASTM D7942-15(2023) - Standard Specification for Thermoplastic Pavement Markings in Non Snow Plow Areas
Effective Date
01-Jul-2010
Referred By
ASTM D5146-10(2019) - Standard Guide to Testing Solvent-Borne Architectural Coatings
Effective Date
01-Jul-2010
Referred By
ASTM D4101-17e1 - Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
Effective Date
01-Jul-2010
Referred By
ASTM D6290-19 - Standard Test Method for Color Determination of Plastic Pellets
Effective Date
01-Jul-2010
Referred By
ASTM D3730-17(2022) - Standard Guide for Testing High-Performance Interior Architectural Wall Coatings
Effective Date
01-Jul-2010
Referred By
ASTM F942-18(2023)e1 - Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
Effective Date
01-Jul-2010
Referred By
ASTM D6605-06(2020) - Standard Practice for Determining the Color Stability of Hydrocarbon Resins After Heating
Effective Date
01-Jul-2010
Referred By
ASTM E1247-12(2017) - Standard Practice for Detecting Fluorescence in Object-Color Specimens by Spectrophotometry
Effective Date
01-Jul-2010
Referred By
ASTM E805-22 - Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials
Effective Date
01-Jul-2010
Referred By
ASTM D8087-18 - Standard Test Method for Color of Maleic Anhydride in the Molten State and After Heating (Platinum-Cobalt Scale) Using Tristimulus Colorimetry
Effective Date
01-Jul-2010
Referred By
ASTM E308-22 - Standard Practice for Computing the Colors of Objects by Using the CIE System
Effective Date
01-Jul-2010
Referred By
ASTM D4020-18 - Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials
Effective Date
01-Jul-2010

Buy Standard

ASTM E313-10 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color CoordinatesASTM E313-10 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
PreviousNext
Standard
ASTM E313-10 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E313-10 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color CoordinatesREDLINE ASTM E313-10 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
PreviousNext
Standard
REDLINE ASTM E313-10 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E313 − 10
StandardPractice for
Calculating Yellowness and Whiteness Indices from
1
Instrumentally Measured Color Coordinates
This standard is issued under the fixed designation E313; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D1925Test Method forYellowness Index of Plastics (With-
4
drawn 1995)
1.1 This practice provides numbers that correlate with
E284Terminology of Appearance
visual ratings of yellowness or whiteness of white and near-
E308PracticeforComputingtheColorsofObjectsbyUsing
white or colorless object-color specimens, viewed in daylight
the CIE System
byanobserverwithnormalcolorvision.Whitetextiles,paints,
E805Practice for Identification of Instrumental Methods of
and plastics are a few of the materials that can be described by
Color or Color-Difference Measurement of Materials
the indices of yellowness or whiteness calculated by this
E991Practice for Color Measurement of Fluorescent Speci-
practice.
mens Using the One-Monochromator Method
1.2 For a complete analysis of object colors, by a specified
E1164PracticeforObtainingSpectrometricDataforObject-
observer and under a specified illuminant, use of three param-
Color Evaluation
etersisrequired.Fornear-whitespecimens,however,itisoften
E1247Practice for Detecting Fluorescence in Object-Color
useful to calculate single-number scales of yellowness or
Specimens by Spectrophotometry
whiteness. This practice provides recommended equations for
E1331Test Method for Reflectance Factor and Color by
such scales and discusses their derivations and uses, and limits
Spectrophotometry Using Hemispherical Geometry
2
to their applicability (see also Ref (1) ).
E1345Practice for Reducing the Effect of Variability of
Color Measurement by Use of Multiple Measurements
1.3 The values stated in SI units are to be regarded as
E1347Test Method for Color and Color-Difference Mea-
standard. No other units of measurement are included in this
surement by Tristimulus Colorimetry
standard.
E1348Test Method for Transmittance and Color by Spec-
1.4 This standard does not purport to address all of the
trophotometry Using Hemispherical Geometry
safety concerns, if any, associated with its use. It is the
E1349Test Method for Reflectance Factor and Color by
responsibility of the user of this standard to establish appro-
Spectrophotometry Using Bidirectional (45°:0° or 0°:45°)
priate safety and health practices and determine the applica-
Geometry
bility of regulatory limitations prior to use.
E1360Practice for Specifying Color by Using the Optical
Society of America Uniform Color Scales System
2. Referenced Documents
E1499Guide for Selection, Evaluation, and Training of
3
2.1 ASTM Standards:
Observers
D1535Practice for Specifying Color by the Munsell System E1541Practice for Specifying and Matching Color Using
4
D1729Practice for Visual Appraisal of Colors and Color
the Colorcurve System (Withdrawn 2007)
Differences of Diffusely-Illuminated Opaque Materials
3. Terminology
3.1 Terms and definitions in Terminology E284 are appli-
cable to this practice.
1
This practice is under the jurisdiction ofASTM Committee E12 on Color and
Appearance and is the direct responsibility of Subcommittee E12.04 on Color and
3.2 Definitions:
Appearance Analysis.
3.2.1 perfect reflecting diffuser, n—ideal reflecting surface
CurrenteditionapprovedJuly1,2010.PublishedJuly2010.Originallyapproved
that neither absorbs nor transmits light, but reflects diffusely,
in 1967. Last previous edition approved in 2005 as E313–05. DOI: 10.1520/
withtheradianceofthereflectingsurfacebeingthesameforall
E0313-10.
2
Theboldfacenumbersinparenthesesrefertothelistofreferencesattheendof
reflecting angles, regardless of the angular distribution of the
this practice.
incident light.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E313 − 10
3.2.2 whiteness, n—the attribute of color perception by 5.3 The combination of measurement and calculation lead-
which an object color is judged to approach the preferred ing to indices of yellowness or whiteness is a psychophysical
white. process, that is, the procedures specified are designed to
provide numbers correlati
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E313–05 Designation:E313–10
Standard Practice for
Calculating Yellowness and Whiteness Indices from
1
Instrumentally Measured Color Coordinates
This standard is issued under the fixed designation E313; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This practice provides numbers that correlate with visual ratings of yellowness or whiteness of white and near-white or
colorless object-color specimens, viewed in daylight by an observer with normal color vision. White textiles, paints, and plastics
are a few of the materials that can be described by the indices of yellowness or whiteness calculated by this practice.
1.2 For a complete analysis of object colors, by a specified observer and under a specified illuminant, use of three parameters
isrequired.Fornear-whitespecimens,however,itisoftenusefultocalculatesingle-numberscalesofyellownessorwhiteness.This
practice provides recommended equations for such scales and discusses their derivations and uses, and limits to their applicability
2
(see also Ref (1) ).
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
D1535 Practice for Specifying Color by the Munsell System
D1729 Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
4
D1925 Test Method for Yellowness Index of Plastics
E284 Terminology of Appearance
E308 Practice for Computing the Colors of Objects by Using the CIE System
E805 Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials
E991 Practice for Color Measurement of Fluorescent Specimens Using the One-Monochromator Method
E1164 Practice for Obtaining Spectrometric Data for Object-Color Evaluation
E1247 Practice for Detecting Fluorescence in Object-Color Specimens by Spectrophotometry
E1331 Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry
E1345 Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements
E1347 Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry
E1348 Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry
E1349 Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45:0 or 0:45) Geometry
E1360 Practice for Specifying Color by Using the Optical Society of America Uniform Color Scales System
E1499 Guide for Selection, Evaluation, and Training of Observers
E1541 Practice for Specifying and Matching Color Using the Colorcurve System
3. Terminology
3.1 Terms and definitions in Terminology E284 are applicable to this practice.
1
This practice is under the jurisdiction of ASTM Committee E12 on Color and Appearance and is the direct responsibility of Subcommittee E12.04 on Color and
Appearance Analysis.
Current edition approved Oct.July 1, 2005.2010. Published October 2005.July 2010. Originally approved in 1967. Last previous edition approved in 20002005 as
E313–005. DOI: 10.1520/E0313-105.
2
The boldface numbers in parentheses refer to the list of references at the end of this practice.
3
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Withdrawn.
4
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E313–10
3.2 Definitions:
3.2.1 perfect reflecting diffuser, n—ideal reflecting surface that neither absorbs nor transmits light, but reflects diffusely, with
the radiance of the reflecting surface being the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E1331-15(2023)(Test Method)
Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry

SIGNIFICANCE AND USE
5.1 The most direct and accessible methods for obtaining the color coordinates of object colors are by instrumental measurement using spectrophotometers or colorimeters with either hemispherical or bidirectional optical measuring systems. This test method provides procedures for such measurement by reflectance spectrophotometry using a hemispherical optical measuring system.  
5.2 This test method is especially suitable for measurement of the following types of specimens for the indicated uses (Guide E179 and Practice E805):  
5.2.1 All types of object-color specimens to obtain data for use in computer colorant formulation.  
5.2.2 Object-color specimens for color assessment.
5.2.2.1 For the measurement of plane-surface high-gloss specimens, the specular component should generally be excluded during the measurement.
5.2.2.2 For the measurement of plane-surface intermediate-gloss specimens and of textured-surface specimens, including textiles, where the first-surface reflection component may be distributed over a wide range of angles, measurement may be made with the specular component included, but the resulting color coordinates may not correlate best with visual judgments of the color. The use of bidirectional geometry, such as 45/0 or 0/45, may lead to better correlations.
5.2.2.3 For the measurement of plane-surface, low-gloss (matte) specimens, the specular component may either be excluded or included, as no significant difference in the results should be apparent.  
5.2.3 Specimens with bare metal surfaces for color assessment. For this application, the specular component should generally be included during the measurement.  
5.3 This test method is not recommended for measurement of the following types of specimens, for which the use of bidirectional measurement geometry (0/45 or 45/0) is preferable (Guide E179):  
5.3.1 Object-color specimens of intermediate gloss,  
5.3.2 Retroreflective specimens, and  
5.3.3 Fluorescent specimens (Practice E...
SCOPE
1.1 This test method describes the instrumental measurement of the reflection properties and color of object-color specimens by the use of a spectrophotometer or spectrocolorimeter with a hemispherical optical measuring system, such as an integrating sphere.  
1.2 The test method is suitable for use with most object-color specimens. However, it should not be used for retroreflective specimens or for fluorescent specimens when highest accuracy is desired. Specimens having intermediate-gloss surfaces should preferably not be measured by use of this geometry.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1247-12(2023)(Practice)
Standard Practice for Detecting Fluorescence in Object-Color Specimens by Spectrophotometry

SIGNIFICANCE AND USE
4.1 Several standards, including Practices E991, E1164, and Test Methods E1331, E1348 and E1349, require either the presence or absence of fluorescence exhibited by the specimen for correct application. This practice provides spectrophotometric procedures for identifying the presence of fluorescence in materials.  
4.2 This practice is applicable to all object-color specimens, whether opaque, translucent, or transparent, meeting the requirements for specimens in the appropriate standards listed in 2.1. Translucent specimens should be measured by reflectance, with a standard non-fluorescent backing material, usually but not necessarily black, placed behind the specimen during measurement.  
4.3 This practice requires the use of a spectrophotometer in which the spectral distribution of the illumination on the specimen can be altered by the user in one of several ways. The modification of the illumination can either be by the insertion of optical filters between the illuminating source and the specimen, without interfering with the detection of the radiation from the specimen, or by interchange of the illuminating and detecting systems of the instrument or by scanning of both the illuminating energy and detection output as in the two-monochromator method.  
4.4 The confirmation of the presence of fluorescence is made by the comparison of spectral curves, color difference, or single parameter difference such as ΔY between the measurements.
Note 2: In editions of E1247 – 92 and earlier, the test of fluorescence was the two sets of spectral transmittances or radiance factor (reflectance factors) differ by 1 % of full scale at the wavelength of greatest difference.  
4.5 Either bidirectional or hemispherical instrument geometry may be used in this practice. The instrument must be capable of providing either broadband (white light) irradiation on the specimen or monochromatic irradiation and monochromatic detection.  
4.6 This practice describes methods to detect the...
SCOPE
1.1 This practice provides spectrophotometric methods for detecting the presence of fluorescence in object-color specimens.
Note 1: Since the addition of fluorescing agents (colorants, whitening agents, etc.) is often intentional by the manufacturer of a material, information on the presence or absence of fluorescent properties in a specimen may often be obtained from the maker of the material.  
1.2 This practice requires the use of a spectrophotometer that both irradiates the specimen over the wavelength range from 340 nm to 700 nm and allows the spectral distribution of illumination on the specimen to be altered as desired.  
1.3 Within the above limitations, this practice is general in scope rather than specific as to instrument or material.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1336-11(2023)(Test Method)
Standard Test Method for Obtaining Colorimetric Data From a Visual Display Unit by Spectroradiometry

SIGNIFICANCE AND USE
5.1 The most fundamental method for obtaining CIE tristimulus values or other color coordinates for describing the colors of visual display units (VDUs) is by the use of spectroradiometric data. (See CIE No. 18 and 63.) These data are used by summation together with numerical values representing the 1931 CIE Standard Observer and normalized to Km, the maximum spectral luminous efficacy function.  
5.2 The special requirements for characterizing VDUs possessing narrow or discontinuous spectra are presented and discussed. Modifications to the requirements of Practice E308 are given to correct for the unusual nature of narrow or discontinuous sources.
SCOPE
1.1 This test method prescribes the instrumental measurements required for characterizing the color and brightness of VDUs.  
1.2 This test method is specific in scope rather than general as to type of instrument and object.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2867-14(2023)(Practice)
Standard Practice for Estimating Uncertainty of Test Results Derived from Spectrophotometry

SIGNIFICANCE AND USE
5.1 Many competent measurement laboratories comply with accepted quality system requirements such as ISO 9001, QS 9000, or ISO 17025. When using standard test methods, the measurement results should agree with those from other similar laboratories within the combined uncertainty limits of the laboratories’ measurement systems. It is for this reason that quality system requirements demand that a statement of the uncertainty of the test results accompany every test result.  
5.2 Preparation of uncertainty estimates is a requirement for laboratory certification under ISO 17025. This practice describes the procedures by which such uncertainty estimates may be calculated.
SCOPE
1.1 This practice describes a protocol to be utilized by measurement laboratories for estimating and reporting the uncertainty of a measurement result when the result is derived from a measurand that has been obtained by spectrophotometry.  
1.2 This practice is specifically limited to the reporting of uncertainty of color measurement results that are reported as color-differences in ΔE format, even though the measurement itself may be reported in other units such as percent reflectance or transmittance.  
1.3 The procedures defined here are not intended to be applicable to national standardizing laboratories or transfer laboratories.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D2244-23(Practice)
Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates

SIGNIFICANCE AND USE
5.1 The original CIE color scales based on tristimulus values X, Y, Z and chromaticity coordinates x, y are not uniform visually. Each subsequent color scale based on CIE values has had weighting factors applied to provide some degree of uniformity so that color differences in various regions of color space will be more nearly comparable. On the other hand, color differences obtained for the same specimens evaluated in different color-scale systems are not likely to be identical. To avoid confusion, color differences among specimens or the associated tolerances should be compared only when they are obtained for the same color-scale system. There is no simple factor that can be used to convert accurately color differences or color tolerances in one system to difference or tolerance units in another system for all colors of specimens.  
5.2 Color differences calculated in ΔE00 units (6) are highly recommended for use with color-differences in the range of 0.0 to 5.0 ΔE*ab units. This color-difference equation is appropriate for and widely used in industrial and commercial applications including, but not limited to, automobiles, coatings, cosmetics, inks, packaging, paints, plastics, printing, security, and textiles.  
5.3 Users of color tolerance equations have found that, in each system, summation of three, vector color-difference components into a single scalar value is very useful for determining whether a specimen color is within a specified tolerance from a standard. However, for control of color in production, it may be necessary to know not only the magnitude of the departure from standard but also the direction of this departure. It is possible to include information on the direction of a small color difference by listing the three instrumentally determined components of the color difference.  
5.4 Selection of color tolerances based on instrumental values should be carefully correlated with a visual appraisal of the acceptability of differences in hue, lig...
SCOPE
1.1 This practice covers the calculation, from instrumentally measured color coordinates based on daylight illumination, of color tolerances and small color differences between opaque specimens such as painted panels, plastic plaques, or textile swatches. Where it is suspected that the specimens may be metameric, that is, possess different spectral curves though visually alike in color, Practice D4086 should be used to verify instrumental results. The tolerances and differences determined by these procedures are expressed in terms of approximately uniform visual color perception in CIE 1976 CIELAB opponent-color space (1),2 CMC tolerance units (2), CIE94 tolerance units (3), the DIN99o color difference formula given in DIN 6176  (4), or the CIEDE2000 color difference units (5).  
1.2 For product specification, the purchaser and the seller shall agree upon the permissible color tolerance between test specimen and reference and the procedure for calculating the color tolerance. Each material and condition of use may require specific color tolerances because other appearance factors, (for example, specimen proximity, gloss, and texture), may affect the correlation between the magnitude of a measured color difference and its commercial acceptability.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D1535-14(2023)(Practice)
Standard Practice for Specifying Color by the Munsell System

SIGNIFICANCE AND USE
4.1 This practice is used by artists, designers, scientists, engineers, and government regulators, to specify an existing or desired color. It is used in the natural sciences to record the colors of specimens, or identify specimens, such as human complexion, flowers, foliage, soils, and minerals. It is used to specify colors for commerce and for control of color-production processes, when instrumental color measurement is not economical. The Munsell system is widely used for color tolerancing, even when instrumentation is employed (see Practice D3134). It is common practice to have color chips made to illustrate an aim color and the just tolerable deviations from that color in hue, value, and chroma, such a set of chips being called a Color Tolerance Set. A color tolerance set exhibits the aim color and color tolerances so that everyone involved in the selection, production, and acceptance of the color can directly perceive the intent of the specification, before bidding to supply the color or starting production. A color tolerance set may be measured to establish instrumental tolerances. Without extensive experience, it may be impossible to visualize the meaning of numbers resulting from color measurement, but by this practice, the numbers can be translated to the Munsell color-order system, which is exemplified by colored chips for visual examination. This color-order system is the basis of the ISCC-NBS Method of Designating Colors and a Dictionary of Color Names, as well as the Universal Color Language, which associates color names, in the English language, with Munsell notations (3).
SCOPE
1.1 This practice provides a means of specifying the colors of objects in terms of the Munsell color order system, a system based on the color-perception attributes hue, lightness, and chroma. The practice is limited to opaque objects, such as painted surfaces viewed in daylight by an observer having normal color vision. This practice provides a simple visual method as an alternative to the more precise and more complex method based on spectrophotometry and the CIE system (see Practices E308 and E1164). Provision is made for conversion of CIE data to Munsell notation.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    41 pages
    English language
    sale 15% off
ASTM
ASTM E1682-08(2022)(Guide)
Standard Guide for Modeling the Colorimetric Properties of a CRT-Type Visual Display Unit

SIGNIFICANCE AND USE
5.1 The color displayed on a VDU is an important aspect of the reproduction of colored images. The VDU is often used as the design, edit, and approval medium. Images are placed into the computer by some sort of capture device, such as a camera or scanner, modified by the computer operator, and sent on to a printer or color separation generator, or even to a paint dispenser or textile dyer. The color of the final product is to have some well-defined relationship to the original. The most common medium for establishing the relationship between input, edit, and output color (device-independent color space) is the CIE tristimulus space. This guide identifies the procedures for deriving a model that relates the digital computer settings of a VDU to the CIE tristimulus values of the colored light emitted by the primaries.
SCOPE
1.1 This guide is intended for use in establishing the operating characteristics of a visual display unit (VDU), such as a cathode ray tube (CRT). Those characteristics define the relationship between the digital information supplied by a computer, which defines an image, and the resulting spectral radiant exitance and CIE tristimulus values. The mathematical description of this relationship can be used to provide a nearby device-independent model for the accurate display of color and colored images on the VDU. The CIE tristimulus values referred to here are those calculated from the CIE 1931 2° standard colorimetric (photopic) observer.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM E179-17(2022)(Guide)
Standard Guide for Selection of Geometric Conditions for Measurement of Reflection and Transmission Properties of Materials

SCOPE
1.1 This guide is intended for use in selecting terminology, measurement scales, and instrumentation for describing or evaluating such appearance characteristics as glossiness, opacity, lightness, transparency, and haziness in terms of reflected or transmitted light. This guide does not consider the spectral variations responsible for color, but the geometric variables described herein can importantly affect instrumentally measured values of color. This guide is general in scope rather than specific as to instrument or material.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM E2301-12(2022)(Test Method)
Standard Test Method for Daytime Colorimetric Properties of Fluorescent Retroreflective Sheeting and Marking Materials for High Visibility Traffic Control and Personal Safety Applications Using 45°:Normal Geometry

SIGNIFICANCE AND USE
5.1 This test method provides procedures for obtaining tristimulus values, luminance factors and chromaticity coordinates of fluorescent-retroreflective materials by bispectral colorimetry using a 45:0 or 0:45 optical measuring system.  
5.2 The CIE 1931 (2°) standard observer is used to calculate the colorimetric properties of fluorescent-retroreflective sheeting and markings used in daytime high visibility traffic control and personal safety applications because in practice these materials are primarily viewed from a distance where they subtend less than 4° of the visual field.  
5.3 This test method is applicable to object-color specimens of any gloss level.  
5.4 Due to the retroreflective properties of these materials the colorimetric data may not be suitable for use in computer colorant formulation.  
5.5 This test method is suitable for quality control testing of fluorescent-retroreflective sheeting and marking materials.
Note 1: Separation of the fluorescence and reflectance components from the total colorimetric properties provides useful and meaningful information to evaluate independently the luminescent and diffuse reflective efficiency and consistency of these materials.  
5.6 This test method is the referee method for determining the conformance of fluorescent-retroreflective sheeting and marking materials to standard daytime colorimetric specifications.
SCOPE
1.1 This test method describes the instrumental measurement of the colorimetric properties (CIE tristimulus values, luminance factors, and chromaticity coordinates) of fluorescent-retroreflective sheeting and marking materials when illuminated by daylight.  
1.2 This test method is generally applicable to any sheeting or marking material having combined fluorescent and retroreflective properties used for daytime high visibility traffic control and personal safety applications.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1477-98a(2022)(Test Method)
Standard Test Method for Luminous Reflectance Factor of Acoustical Materials by Use of Integrating-Sphere Reflectometers

SIGNIFICANCE AND USE
5.1 Acoustical materials are often used as the entire ceiling of rooms and are therefore an important component of the lighting system. The luminous reflectance of all important components must be known in order to predict the level of illumination that will be obtained.  
5.2 The reflecting properties of a surface are measured relative to those of a standard reflector, the perfect reflecting diffuser, to provide a reflectance factor. The luminous reflectance factor is calculated for a standard illuminant, and a standard observer, for the standard hemispherical (integrating-sphere) geometry of illumination and viewing, in which all reflected radiation from an area of the surface is collected. In this way the reflecting properties of an acoustical material can be represented by a single number measured and calculated under standard conditions.  
5.3 Acoustical materials generally have a non-glossy white or near-white finish. The types of surface cover a wide range from smooth to deeply fissured. Measurement with integrating-sphere reflectometers has been satisfactory although multiple measurements may be required to sample the surface adequately. Instruments with other types of optical measuring systems may be used if it can be demonstrated that they provide equivalent results.  
5.4 The use of this test method for determining the luminous reflectance factor is required by Classification E1264.
SCOPE
1.1 This test method covers the measurement of the luminous reflectance factor of acoustical materials for use in predicting the levels of room illumination.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off