ASTM A666-15
(Specification)Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
ABSTRACT
This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions. They shall be formed in different shapes such as sheets, strips, plates and flat bars. The steels shall adhere to specified chemical composition requirements. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined. The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test.
SCOPE
1.1 This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions for various structural, pressure vessel, magnetic, cryogenic, and heat-resisting applications. (This revision of Specification A666 replaces prior Specifications A412 and A177.)
1.2 The application of this specification, or the use of material covered by this specification does not automatically allow usage in pressure vessel applications. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A666 − 15
Standard Specification for
Annealed or Cold-Worked Austenitic Stainless Steel Sheet,
1
Strip, Plate, and Flat Bar
This standard is issued under the fixed designation A666; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 4. Chemical Composition
1.1 This specification covers austenitic stainless steels in the 4.1 The steel shall conform to the requirements as to
annealed and normally required cold-worked conditions for chemical composition specified in Table 1, and shall conform
various structural, pressure vessel, magnetic, cryogenic, and
to applicable requirements specified in the current edition of
heat-resisting applications. (This revision of Specification Specification A480/A480M.
A666 replaces prior Specifications A412 and A177.)
5. Mechanical Properties
1.2 The application of this specification, or the use of
5.1 The material shall conform to the mechanical properties
material covered by this specification does not automatically
specified in Tables 2 and 3, or Tables 2 and 4.
allow usage in pressure vessel applications. Only annealed
conditions of grades specifically approved by the ASME code
6. General Requirements
are permitted for pressure vessel use.
6.1 The following requirements for orders for material
1.3 The values stated in inch-pound units are to be regarded
furnished under this specification shall conform to the appli-
as the standard. The values given in parentheses are for
cable requirements of the current edition of Specification
information only.
A480/A480M or A484/A484M:
6.1.1 Definitions,
2. Referenced Documents
6.1.2 General requirements for delivery,
2
2.1 ASTM Standards:
6.1.3 Ordering information,
A240/A240M Specification for Chromium and Chromium-
6.1.4 Process,
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
6.1.5 Special tests,
Vessels and for General Applications
6.1.6 Heat treatment,
A370 Test Methods and Definitions for Mechanical Testing
6.1.7 Dimensions and permissible variations,
of Steel Products
6.1.8 Workmanship, finish and appearance,
A480/A480M Specification for General Requirements for
6.1.9 Number of tests/test methods,
Flat-Rolled Stainless and Heat-Resisting Steel Plate,
6.1.10 Specimen preparation,
Sheet, and Strip
6.1.11 Retreatment,
A484/A484M Specification for General Requirements for
6.1.12 Inspection,
Stainless Steel Bars, Billets, and Forgings
6.1.13 Rejection and rehearing,
3. Material Test Report and Certification 6.1.14 Material test report,
6.1.15 Certification, and
3.1 In addition to the requirements of Specification A480/
6.1.16 Packaging, marking, and loading.
1 1
A480M, the cold-worked condition (annealed, ⁄4 H, ⁄2 H, and
so forth) shall be noted.
7. Sampling
7.1 Tension and bend-test specimens of sheet, strip, and
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
plate products shall be selected from finished material and shall
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.17 on Flat-Rolled and Wrought Stainless Steel.
be selected in the transverse direction, except in the case of
Current edition approved March 1, 2015. Published March 2015. Originally
strip under 9 in. (229 mm) in width, in which case tension test
approved in 1972. Last previous edition approved in 2010 as A666 – 10. DOI:
specimens shall be selected in the longitudinal direction.
10.1520/A0666-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
7.2 Flat bar tension and bend-test specimens shall be se-
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
lected from the finished material and shall be in the longitudi-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. nal direction.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A666 − 15
A
TABLE 1 Chemical Composition Requirements
B
Type UNS Composition, %
Designation
Carbon Manganese Phosphorus Sulfur Silicon Chromium Nickel Other
Elements
201 S20100 0.15 5.5–7.5 0.060 0.030 0.75 16.0–18.0 3.5–5.5 N 0.25
201L S20103 0.03 5.5–7.5 0.045 0.030 0.75 16.0–18.0 3.5–5.5 N 0.25
201LN S20153 0.03 6.4–7.5 0.045 0.015 0.75 16.0–17.5 4.0–5.0 N 0.10–0.25
Cu 1.00
202 S20200 0.15 7.5–10.0 0.060 0.030 0.75 17.0–19.0 4.0–6.0 N 0.25
. . . S20400 0.030 7.
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A666 − 10 A666 − 15
Standard Specification for
Annealed or Cold-Worked Austenitic Stainless Steel Sheet,
1
Strip, Plate, and Flat Bar
This standard is issued under the fixed designation A666; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions for various
structural, architectural, pressure vessel, magnetic, cryogenic, and heat-resisting applications. (This revision of Specification A666
replaces prior Specifications A412 and A177.)
1.2 The application of this specification, or the use of material covered by this specification does not automatically allow usage
in pressure vessel applications. Only annealed conditions of grades specifically approved by the ASME code are permitted for
pressure vessel use.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
2. Referenced Documents
2
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
3. Material Test Report and Certification
1 1
3.1 In addition to the requirements of Specification A480/A480M, the cold-worked condition (annealed, ⁄4 H, ⁄2 H, and so
forth) shall be noted.
4. Chemical Composition
4.1 The steel shall conform to the requirements as to chemical composition specified in Table 1, and shall conform to applicable
requirements specified in the current edition of Specification A480/A480M.
5. Mechanical Properties
5.1 The material shall conform to the mechanical properties specified in Table 2Tables 2 and 3 and Table 3, or Table 2Tables
2 and 4 and Table 4.
6. General Requirements
6.1 The following requirements for orders for material furnished under this specification shall conform to the applicable
requirements of the current edition of Specification A480/A480M or A484/A484M:
6.1.1 Definitions,
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Sept. 1, 2010March 1, 2015. Published September 2010March 2015. Originally approved in 1972. Last previous edition approved in 20032010
as A666 – 03.A666 – 10. DOI: 10.1520/A0666-10.10.1520/A0666-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A666 − 15
A
TABLE 1 Chemical Composition Requirements
B
Type UNS Composition, %
Designation
Carbon Manganese Phosphorus Sulfur Silicon Chromium Nickel Other
Elements
201 S20100 0.15 5.5–7.5 0.060 0.030 0.75 16.0–18.0 3.5–5.5 N 0.25
201L S20103 0.03 5.5–7.5 0.045 0.030 0.75 16.0–18.0 3.5–5.5 N 0.25
201LN S20153 0.03 6.4–7.5 0.045 0.015 0.75 16.0–17.5 4.0–5.0 N 0.10–0.25
Cu 1.00
202 S20200 0.15 7.5–10.0 0.060 0.030 0.75 17.0–19.0 4.0–6.0 N 0.25
. . . S20400 0.030 7.0–9.0 0.040 0.030 1.00 15.0–17.0 1.50–3.00 N 0.15–0.30
205 S20500 0.12–0.25 14.0–15.0 0.060 0.030 0.75 16.5–18.0 1.00–1.75 N 0.32–0.40
301 S30100 0.15 2.00 0.045 0.030 1.00 16.0–18.0 6.0–8.0 N 0.10
301L S30103 0.03 2.00 0.045 0.030 1.00 16.0–18.0 6.0–8.0 N 0.20
301LN S30153 0.03 2.00 0.045 0.030 1.00 16.0–18.0 6.0–8.0 N 0.07–0.20
301Si S30116 0.15 2.00 0.045 0.030 1.00–1.35 16.0–18.0 6.0–8.0 N 0.20,
Mo 1.00
302 S30200 0.15 2.00 0.045 0.030 0.75 17.0–19
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.