ASTM F1900-98(2017)
(Test Method)Standard Test Method for Water Resistance of Footwear Using a Walking Step Simulator
Standard Test Method for Water Resistance of Footwear Using a Walking Step Simulator
SIGNIFICANCE AND USE
3.1 Water resistance is a desirable characteristic for many different types of footwear. This test method provides a guide for measuring water resistance under dynamic conditions that closely duplicate normal human walking. The degree of correlation between this test and footwear performance in the field or footwear performance in the SATRA Trough-Water Penetration Test has not been fully determined.
SCOPE
1.1 This test method covers a method of measuring the water resistance of footwear.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F1900 − 98 (Reapproved 2017) An American National Standard
Standard Test Method for
Water Resistance of Footwear Using a Walking Step
Simulator
This standard is issued under the fixed designation F1900; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope for measuring water resistance under dynamic conditions that
closely duplicate normal human walking. The degree of
1.1 This test method covers a method of measuring the
correlation between this test and footwear performance in the
water resistance of footwear.
field or footwear performance in the SATRA Trough-Water
1.2 This standard does not purport to address all of the
Penetration Test has not been fully determined.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
4. Apparatus
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
4.1 Mechanism, such as the one shown in Fig. 1, that
1.3 This international standard was developed in accor-
approximates the movements and forces involved in human
dance with internationally recognized principles on standard-
walking motion. The important features of the walking motion
ization established in the Decision on Principles for the
produced by the mechanism are defined as follows:
Development of International Standards, Guides and Recom-
4.1.1 At the beginning of a step (the point where the heel of
mendations issued by the World Trade Organization Technical
the footwear touches the walking surface) the leg pylon
Barriers to Trade (TBT) Committee.
attached to the prosthetic foot shall form an angle of 16 6 5°
2. Referenced Documents (relative to a line perpendicular to the walking surface) as
shown in Fig. 2.
2.1 ASTM Standards:
4.1.2 At the end of a step (the point where the toe of the
D2098 Test Method for Dynamic Water Resistance of Shoe
Upper Leather by the Dow Corning Leather Tester footwear departs from the walking surface) the leg pylon shall
D2099 Test Method for Dynamic Water Resistance of Shoe form an angle 31 6 5° (see Fig. 2).
Upper Leather by the Maeser Water Penetration Tester
4.1.3 Each step shall begin with no force being exerted on
2.2 SATRA Test Method:
the footwear and with the footwear not in contact with the
Physical Test Method PM81 Trough-Water Penetration Test
walking surface. When the footwear contacts the walking
2.3 FIA Test Methods:
surface, it shall remain in contact during the entire support
No. 1209, Appendix B—Whole Shoe Flex in Water
phase of the step and then depart from the walking surface at
the end of the step.
3. Significance and Use
4.1.4 During the support phase of each step, a downward
3.1 Water resistance is a desirable characteristic for many
force shall be applied to the footwear to simulate the weight of
different types of footwear. This test method provides a guide
the user. The force shall equal one bodyweight of the typical
prospective user, with a tolerance of 610 %, unless a different
force is specified. Table 1 lists the body masses of 50th
This test method is under the jurisdiction of ASTM Committee F08 on Sports
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
percentile adults and children, and the equivalent one body-
Subcommittee F08.54 on Athletic Footwear.
weight downward force levels. If no other downward force is
Current edition approved Sept. 1, 2017. Published December 2017. Originally
specified, the values in Table 1 shall be used.
approved in 1998. Last previous edition approved in 2012 as F1900 – 98 (2012).
DOI: 10.1520/F1900-98R17.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or NOTE 1—The force under the prosthetic foot can be measured with a
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
load cell or force plate.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 4.2 Men’s 26-cm (U.S. Size 9) or Women’s 24-cm (U.S. Size
Available from SATRA Footwear Technology Centre, Rockingham Road,
7)RightorLeftProstheticFoot,shallbeusedunlessadifferent
Kettering, Northamptonshire, NN16 9JH, United Kingdom.
4 size is specified. The foot shall closely approximate the shape,
Available from Footwear Industries of America, 1420 K St. NW, Suite 600,
Washington, DC. texture, and flexibility of a human foot.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1900 − 98 (2017)
(1) Prosthetic foot with moisture sensors
(2) Water tank
(3) Motor with speed control
(4) Mechanism for producing back and forth motion
(5) Cam to control location of knee
(6) Cam to control location of ankle
(7) Slide mechanism
(8) Air cylinder to lower the foot at the beginning of each step and raise it again at the completion of each
step
FIG. 1 Footwear Tester
4.2.1 Aminimum of six moisture sensors shall be placed at 4.3 Water Tank, made of stainless steel (or other corrosion-
the following locations on the prosthetic foot: instep, big toe, resistant material). The tank shall be large enough so that the
inner and outer ball, and inner and outer heel, as illustrated in
upper portion of a shoe or boot does not come in contact with
Fig. 3.
the tank at any time during the test. The tank should have an
4.2.2 The moisture sensors shall determine the presence of
opening in the front, that is covered by transparent material, to
water. A circuit diagram for a sensor that has proven to be
permit observation of the footwear during the test.
suitable for this application is shown in Fig. 4.
F1900 − 98 (2017)
FIG. 2 Typical Ranges of Motion During Ground Contact During Walking at 3.2 kph (2.0 mph)
TABLE 1 Body Masses and Equivalent One Bodyweight
NOTE 3—Socks
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.