ASTM D6327-10(2021)
(Test Method)Standard Test Method for Determination of Radon Decay Product Concentration and Working Level in Indoor Atmospheres by Active Sampling on a Filter
Standard Test Method for Determination of Radon Decay Product Concentration and Working Level in Indoor Atmospheres by Active Sampling on a Filter
SIGNIFICANCE AND USE
5.1 The test method provides a relatively simple method for determination of the concentration of RDP without the need for specialty equipment built expressly for such purposes.
5.2 Using this test method will afford investigators of radon in dwellings a technique by which the RDP can be determined. The use of the results of this test method are generally for diagnostic purposes and are not necessarily indicative of results that might be obtained by longer term measurement methods.
5.3 An improved understanding of the frequency of elevated radon in buildings and the health effect of exposure has increased the importance of knowledge of actual exposures. The measurement of RDP, which are the direct cause of potential adverse health effects, should be conducted in a manner that is uniform and reproducible; it is to this end that this test method is addressed.
SCOPE
1.1 This test method provides instruction for using the grab sampling filter technique to determine accurate and reproducible measurements of indoor radon decay product (RDP) concentrations and of the working level (WL) value corresponding to those concentrations.
1.2 Measurements made in accordance with this test method will produce RDP concentrations representative of closed-building conditions. Results of measurements made under closed-building conditions will have a smaller variability and are more reproducible than measurements obtained when building conditions are not controlled. This test method may be utilized under non-controlled conditions, but a greater degree of variability in the results will occur. Variability in the results may also be an indication of temporal variability present at the sampling site.
1.3 This test method utilizes a short sampling period and the results are indicative of the conditions only at the place and time of sampling. The results obtained by this test method are not necessarily indicative of longer terms of sampling and should not be confused with such results. The averaging of multiple measurements over hours and days can, however, provide useful screening information. Individual measurements are generally obtained for diagnostic purposes.
1.4 The range of the test method may be considered from 0.0005 WL to unlimited working levels, and from 40 Bq/m3 to unlimited for each individual radon decay product.
1.5 This test method provides information on equipment, procedures, and quality control. It provides for measurements within typical residential or building environments and may not necessarily apply to specialized circumstances, for example, clean rooms.
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 9 for additional precautions
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
- Status
- Published
- Publication Date
- 31-Aug-2021
- Technical Committee
- D22 - Air Quality
- Drafting Committee
- D22.05 - Indoor Air
Relations
- Effective Date
- 01-Sep-2020
- Effective Date
- 15-Mar-2020
- Effective Date
- 01-Mar-2017
- Effective Date
- 15-Oct-2015
- Effective Date
- 01-Jul-2015
- Effective Date
- 01-Dec-2014
- Effective Date
- 01-May-2014
- Effective Date
- 15-Jan-2014
- Effective Date
- 01-May-2013
- Effective Date
- 01-Oct-2011
- Effective Date
- 01-Apr-2010
- Effective Date
- 01-Nov-2007
- Effective Date
- 01-Oct-2007
- Effective Date
- 01-Nov-2005
- Effective Date
- 01-May-2005
Overview
ASTM D6327-10(2021) is the internationally recognized standard test method for the determination of radon decay product (RDP) concentration and working level (WL) in indoor atmospheres using active sampling on a filter. Developed by ASTM International, this method provides clear instructions for accurate and reproducible short-term measurements of indoor radon decay products-a critical factor in assessing human exposure to radon and its potential health impacts. The test method utilizes a grab sampling filter technique and is intended for use primarily in typical residential or building environments.
Key Topics
- Radon Decay Products (RDP): Focuses on isotopes including polonium-218, lead-214, bismuth-214, and polonium-214, which are fundamental to evaluating radon exposure.
- Working Level (WL): Defines exposure based on the concentration of short-lived radon decay products in air, expressed as a unit commonly used for environmental RDP assessment.
- Grab Sampling Filter Technique: A short-term air sampling approach using a calibrated air pump and membrane filters, suitable for quick and representative snapshots of indoor air quality regarding radon.
- Measurement Conditions: Measurements made under closed-building conditions yield more consistent and reproducible data than those in uncontrolled settings.
- Diagnostic Application: Generally used for diagnostic or screening purposes, not as a substitute for long-term radon measurements.
- Uniformity and Reproducibility: Emphasizes procedures for consistent quality control, calibration, and data reliability.
Applications
The ASTM D6327-10(2021) standard is widely used in the following practical applications:
- Indoor Air Quality Assessment: Ideal for health and environmental professionals seeking to evaluate radon decay product concentrations in homes, offices, and public buildings.
- Regulatory and Health Screening: Supports rapid diagnostic testing to identify areas with potentially elevated radon exposure, aiding in compliance with health guidelines or regulations.
- Short-Term Investigations: Useful for real estate transactions, remediation follow-ups, or when quick radon exposure data is required.
- Quality Control in Radon Testing: Outlines steps for equipment calibration, sampling, and analysis to ensure accurate results.
- Research and Study: Assists researchers in quantifying short-term variability of radon decay products and assessing the effectiveness of radon mitigation measures.
Related Standards
Professionals implementing ASTM D6327-10(2021) may also reference these related standards for comprehensive indoor air sampling and analysis:
- ASTM D1356 - Terminology Relating to Sampling and Analysis of Atmospheres
- ASTM E1 - Specification for ASTM Liquid-in-Glass Thermometers
- ASTM D3631 - Test Methods for Measuring Surface Atmospheric Pressure
- EPA 402–R–92–004 - US EPA Protocols for Measuring Indoor Radon Decay Products
These documents provide complementary guidance on terminology, instrumentation, and additional test procedures relevant to radon and indoor air quality evaluation.
By adhering to ASTM D6327-10(2021), organizations ensure that radon decay product measurements are conducted in a reliable, reproducible, and internationally recognized manner. This standard is essential for effective indoor air quality management, regulatory compliance, and the promotion of healthy living environments. For more information and access to the full standard, visit the ASTM International website.
Get Certified
Connect with accredited certification bodies for this standard
NSF International
Global independent organization facilitating standards development and certification.
CIS Institut d.o.o.
Personal Protective Equipment (PPE) certification body. Notified Body NB-2890 for EU Regulation 2016/425 PPE.
Kiwa BDA Testing
Building and construction product certification.
Sponsored listings
Frequently Asked Questions
ASTM D6327-10(2021) is a standard published by ASTM International. Its full title is "Standard Test Method for Determination of Radon Decay Product Concentration and Working Level in Indoor Atmospheres by Active Sampling on a Filter". This standard covers: SIGNIFICANCE AND USE 5.1 The test method provides a relatively simple method for determination of the concentration of RDP without the need for specialty equipment built expressly for such purposes. 5.2 Using this test method will afford investigators of radon in dwellings a technique by which the RDP can be determined. The use of the results of this test method are generally for diagnostic purposes and are not necessarily indicative of results that might be obtained by longer term measurement methods. 5.3 An improved understanding of the frequency of elevated radon in buildings and the health effect of exposure has increased the importance of knowledge of actual exposures. The measurement of RDP, which are the direct cause of potential adverse health effects, should be conducted in a manner that is uniform and reproducible; it is to this end that this test method is addressed. SCOPE 1.1 This test method provides instruction for using the grab sampling filter technique to determine accurate and reproducible measurements of indoor radon decay product (RDP) concentrations and of the working level (WL) value corresponding to those concentrations. 1.2 Measurements made in accordance with this test method will produce RDP concentrations representative of closed-building conditions. Results of measurements made under closed-building conditions will have a smaller variability and are more reproducible than measurements obtained when building conditions are not controlled. This test method may be utilized under non-controlled conditions, but a greater degree of variability in the results will occur. Variability in the results may also be an indication of temporal variability present at the sampling site. 1.3 This test method utilizes a short sampling period and the results are indicative of the conditions only at the place and time of sampling. The results obtained by this test method are not necessarily indicative of longer terms of sampling and should not be confused with such results. The averaging of multiple measurements over hours and days can, however, provide useful screening information. Individual measurements are generally obtained for diagnostic purposes. 1.4 The range of the test method may be considered from 0.0005 WL to unlimited working levels, and from 40 Bq/m3 to unlimited for each individual radon decay product. 1.5 This test method provides information on equipment, procedures, and quality control. It provides for measurements within typical residential or building environments and may not necessarily apply to specialized circumstances, for example, clean rooms. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 9 for additional precautions 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
SIGNIFICANCE AND USE 5.1 The test method provides a relatively simple method for determination of the concentration of RDP without the need for specialty equipment built expressly for such purposes. 5.2 Using this test method will afford investigators of radon in dwellings a technique by which the RDP can be determined. The use of the results of this test method are generally for diagnostic purposes and are not necessarily indicative of results that might be obtained by longer term measurement methods. 5.3 An improved understanding of the frequency of elevated radon in buildings and the health effect of exposure has increased the importance of knowledge of actual exposures. The measurement of RDP, which are the direct cause of potential adverse health effects, should be conducted in a manner that is uniform and reproducible; it is to this end that this test method is addressed. SCOPE 1.1 This test method provides instruction for using the grab sampling filter technique to determine accurate and reproducible measurements of indoor radon decay product (RDP) concentrations and of the working level (WL) value corresponding to those concentrations. 1.2 Measurements made in accordance with this test method will produce RDP concentrations representative of closed-building conditions. Results of measurements made under closed-building conditions will have a smaller variability and are more reproducible than measurements obtained when building conditions are not controlled. This test method may be utilized under non-controlled conditions, but a greater degree of variability in the results will occur. Variability in the results may also be an indication of temporal variability present at the sampling site. 1.3 This test method utilizes a short sampling period and the results are indicative of the conditions only at the place and time of sampling. The results obtained by this test method are not necessarily indicative of longer terms of sampling and should not be confused with such results. The averaging of multiple measurements over hours and days can, however, provide useful screening information. Individual measurements are generally obtained for diagnostic purposes. 1.4 The range of the test method may be considered from 0.0005 WL to unlimited working levels, and from 40 Bq/m3 to unlimited for each individual radon decay product. 1.5 This test method provides information on equipment, procedures, and quality control. It provides for measurements within typical residential or building environments and may not necessarily apply to specialized circumstances, for example, clean rooms. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 9 for additional precautions 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D6327-10(2021) is classified under the following ICS (International Classification for Standards) categories: 13.040.01 - Air quality in general. The ICS classification helps identify the subject area and facilitates finding related standards.
ASTM D6327-10(2021) has the following relationships with other standards: It is inter standard links to ASTM D1356-20a, ASTM D1356-20, ASTM D3631-99(2017), ASTM D1356-15a, ASTM D1356-15, ASTM D1356-14b, ASTM D1356-14a, ASTM D1356-14, ASTM E1-13, ASTM D3631-99(2011), ASTM D1356-05(2010), ASTM E1-07, ASTM D3631-99(2007), ASTM E1-05, ASTM D1356-05. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
ASTM D6327-10(2021) is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D6327 − 10 (Reapproved 2021)
Standard Test Method for
Determination of Radon Decay Product Concentration and
Working Level in Indoor Atmospheres by Active Sampling
on a Filter
This standard is issued under the fixed designation D6327; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.6 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
1.1 This test method provides instruction for using the grab
standard.
sampling filter technique to determine accurate and reproduc-
1.7 This standard does not purport to address all of the
ible measurements of indoor radon decay product (RDP)
safety concerns, if any, associated with its use. It is the
concentrations and of the working level (WL) value corre-
responsibility of the user of this standard to establish appro-
sponding to those concentrations.
priate safety, health, and environmental practices and deter-
1.2 Measurementsmadeinaccordancewiththistestmethod
mine the applicability of regulatory limitations prior to use.
will produce RDP concentrations representative of closed-
See Section 9 for additional precautions
building conditions. Results of measurements made under
1.8 This international standard was developed in accor-
closed-building conditions will have a smaller variability and
dance with internationally recognized principles on standard-
are more reproducible than measurements obtained when ization established in the Decision on Principles for the
buildingconditionsarenotcontrolled.Thistestmethodmaybe
Development of International Standards, Guides and Recom-
utilized under non-controlled conditions, but a greater degree mendations issued by the World Trade Organization Technical
of variability in the results will occur. Variability in the results Barriers to Trade (TBT) Committee.
may also be an indication of temporal variability present at the
2. Referenced Documents
sampling site.
2.1 ASTM Standards:
1.3 Thistestmethodutilizesashortsamplingperiodandthe
D1356Terminology Relating to Sampling and Analysis of
results are indicative of the conditions only at the place and
Atmospheres
time of sampling. The results obtained by this test method are
D1605Practices for Sampling Atmospheres for Analysis of
not necessarily indicative of longer terms of sampling and
Gases and Vapors (Withdrawn 1992)
should not be confused with such results. The averaging of
D3631Test Methods for Measuring Surface Atmospheric
multiple measurements over hours and days can, however,
Pressure
provide useful screening information. Individual measure-
E1Specification for ASTM Liquid-in-Glass Thermometers
ments are generally obtained for diagnostic purposes.
3. Terminology
1.4 The range of the test method may be considered from
0.0005WLto unlimited working levels, and from 40 Bq/m to 3.1 Definitions—For definitions of terms used in this test
unlimited for each individual radon decay product. method, refer to Terminology D1356.
3.2 Definitions of Terms Specific to This Standard:
1.5 This test method provides information on equipment,
3.2.1 grab sampling, n—the act and all procedures involved
procedures, and quality control. It provides for measurements
with obtaining a short term sample through the use of an
within typical residential or building environments and may
operating air pump.
not necessarily apply to specialized circumstances, for
example, clean rooms.
3.2.2 radon, n—the particular isotope radon-222.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
This test method is under the jurisdiction of ASTM Committee D22 on Air contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Quality and is the direct responsibility of Subcommittee D22.05 on Indoor Air. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Sept. 1, 2021. Published September 2021. Originally the ASTM website.
approved in 1998. Last previous edition approved in 2016 as D6327–10 (2016). The last approved version of this historical standard is referenced on
DOI: 10.1520/D6327-10R21. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D6327 − 10 (2021)
3.2.3 radon decay products (RDP), n—any or all of the 7. Apparatus
particular isotopes polonium-218, bismuth-214, lead-214, and
7.1 Collection Apparatus:
polonium-214.
7.1.1 Air pump capable of 10 to 12 L/min flow rate.
3.2.4 working level, n—quantity of short-lived decay prod-
7.1.2 Bubble tube airflow calibration cell, 1 L or larger.
uctsthatwillresultin1.3×10 MeVofpotentialalphaenergy
7.1.3 Calibrated dry gas meter.
per litre of air. The working level is the common unit for
7.1.4 Flow meter (optional).
expressing environmental RDP exposure.
7.1.5 Open-faced filter holder, 25 or 47-mm diameter.
7.1.6 Membrane filters, mixed cellulose ester, 25 or 47-mm
4. Summary of Test Method (1)
diameter, 0.8-µm pore size.
4.1 Grab sampling measurements of RDPconcentrations in
7.1.7 Sharpened forceps, for removal of sample filters.
airareperformedbycollectingtheRDPfromaknownvolume
7.1.8 Stopwatch, accurate to 1 s.
of air on a filter and subsequently counting the activity on the
7.2 Decay Counting Apparatus:
filter following collection. The counting is performed at
7.2.1 Zinc sulfide phosphor discs, 51-mm diameter.
specified times for specified periods. The energy from radio-
7.2.2 Scintillation Counter, scaler and photomultiplier tube.
active decay of the particles collected on the filter is converted
7.2.3 High voltage power supply.
to light pulses by a zinc sulfide phosphor in contact with the
filter. The light pulses are detected and converted to counts.
7.3 Thermometer (see Specification E1).
Analysis of the number of counts in each counting interval
7.4 Barometer (see Test Methods D3631).
determines the concentrations of the RDP. The two counting
methods which have found the most general use are the
8. Reagents and Materials
Kusnetz and the modified Tsivoglou procedures (2).
8.1 National Institute of Standards and Technology (NIST)
traceable alpha calibration source, typically americium-241, to
5. Significance and Use
determine counter efficiency (4, 5).
5.1 Thetestmethodprovidesarelativelysimplemethodfor
determinationoftheconcentrationofRDPwithouttheneedfor
9. Hazards
specialty equipment built expressly for such purposes.
9.1 Since radioactive material is being utilized, both in the
5.2 Using this test method will afford investigators of radon
form of calibration standards and particles collected on sample
indwellingsatechniquebywhichtheRDPcanbedetermined.
filters, wear disposable gloves during handling of these items.
The use of the results of this test method are generally for
diagnosticpurposesandarenotnecessarilyindicativeofresults 9.2 Iftheatmospheresbeingmeasuredareknowntocontain
that might be obtained by longer term measurement methods. high concentrations of RDP, wear an HEPA half-mask respi-
rator during sampling.
5.3 Animprovedunderstandingofthefrequencyofelevated
radon in buildings and the health effect of exposure has 9.3 The calibration source from NIST must be shielded
increased the importance of knowledge of actual exposures. when not being used for calibration. Shield the source by
The measurement of RDP, which are the direct cause of returningthesourcetotheoriginalNISTstoragecontainerand
potential adverse health effects, should be conducted in a placing the source in the original storage geometry within the
manner that is uniform and reproducible; it is to this end that container (4).
this test method is addressed.
10. Preparation of Apparatus
6. Interferences
10.1 Verify proper operation of the equipment prior to
6.1 Interferences may be caused by any alpha-emitting
collection of the sample. Refer to equipment manuals for
particle capable of inducing a light pulse in the phosphor
information.
screen used for alpha-counting. In general, the only significant
10.1.1 Operate each counting system at the high-voltage
interference source is that of the decay products of radon-220,
(HV) and threshold settings that combines maximum stability,
thoron, which may be considerable in certain geographical
good counting efficiency, and low background counts. Each
regions. The direction of the interference is always positive.
manufacturer’s counting systems have different set-up require-
The extent to which thoron decay products interfere can be
ments and optimization procedures. A general similar proce-
estimated or measured through alpha-spectroscopy or serial
dure is available (6).
type measurements (3).
10.2 Determine the counter efficiency and background for
6.2 Some depth penetration to the filter may occur. The
the sampling filter and phosphor screen pair prior to collection
extent of the penetration may be estimated using membrane
of the sample (see Section 11).
filtertypesnotsuggestedwithinthistestmethod.Thedirection
10.3 The air pump, filter assembly, and connecting tubing
of interferences is always negative.
shall not leak.
10.4 A volume meter is needed for measuring total sample
flow. A calibrated dry gas test meter is the most satisfactory
The boldface numbers in parentheses refer to a list of references at the end of
this standard. totalvolumemeteravailableforsourcetestwork.Calibratethe
D6327 − 10 (2021)
meter in the laboratory prior to use with a positive displace- 11.2.3 Obtain a count measurement for 10 min. For every
ment liquid meter or a cylinder and piston flow calibrator, and set of measurements, utilize a phosphor disc that no longer
determine a meter correction factor, C , as necessary. shows enhanced activity from previous sampling measure-
M
ments. Use the same phosphor disc for a filter before and after
10.5 Locate the scintillation counter to provide rapid access
collection of a sample with the filter. If the total count for 10
from the sampling site when the modified Tsivoglou counting
min is greater than 10, replace the filter and phosphor disc pair
procedureisutilized.Thisprocessisnecessaryduetotheshort
and recount. The number is the background count, B, and is
time period between sampling and the start of counting.
recorded in counts.
11.2.4 Remove the filter from the phosphor disc with the
11. Procedure
forceps and place in the filter holder with the counted side
11.1 Calibration of Scintillation Counter:
exposed to the air.
11.1.1 Determine the efficiency of the scintillation counter
11.2.5 Reassemble the filter holder with care to prevent
through use of the NIST-traceable alpha-emitting calibration
tearing of the filter.
point source.
11.2.6 Obtain the initial dry gas meter reading.
11.1.2 Deactivate the photomultiplier tube. Exposure of an
11.2.7 Draw sample air through the filter for 5.00 min.
activated photomultiplier tube to light while connected to
11.2.8 Obtain the final dry gas meter reading and record the
power may permanently damage the photomultiplier tube.
volume of air sampled in litres, V.
NOTE 1—Although comments have been received indicating
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...