ASTM B133-93A

Specification for Copper Rod, Bar, and Shapes (Withdrawn 1994)

General Information

• Status: Withdrawn
• Technical Committee: B05 - Copper and Copper Alloys
• Drafting Committee: B05.02 - Rod, Bar, Wire, Shapes and Forgings

Standards Content (Sample)

ASTM BI33 REV*A 93 = 0759530 0534345 432 =
AMERICAN SOCIETY FOR TESTING AND MATERIALS
Designation: B 133 - 93a
191 6 Race St Philadelphia, Pa 191 03
Reprinted from the Annual Book of ASTM Standards. Copyright ASTM
4cni
If not listed in the current combined index, will appear in the nexi ediiwn.
Standard Specification for
Copper Rod, Bar, and Shapes’
This standard is issued under the fixed designation B 133; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (c) indicates an editorial change since the last revision or reapproval.
This speci/icaiion has been approved for use by agencies of ihe Deparimeni of Defense. Consuli ihe DoD index of Specificaiions and
Siandards for the specific year of issue rhai has been adopied by ihe Deparimeni oJDefense.
B 193 Test Method for Resistivity of Electrical Conductor
1. Scope
Materials4
1.1 This specification2 covers copper rod, bar, and shapes
B 224 Classification of Coppers4
for general purposes. The following coppers are covered:
B 249 Specification for General Requirements for
Reference Designation”
Copper UNS NO.^
Wrought Copper and Copper-Alloy Rod, Bar, and
OFE
CIO100
Shapes4
CI0200 OF
B 577 Test Methods for Hydrogen Embnttlement of
C 10300 OFXLP
OFS
CIO400
COPpefl
CI0500 OFS
B 601 Practice for Temper Designations for Copper and
OFS
CI0700
Copper Alloys-Wrought and Cast“
OFLP
CIO800
ETP E 8 Test Methods for Tension Testing of Metallic
CI 1000
CI2000 DLP
Materialss
DHP
c I2200
E 18 Test Methods for Rockwell Hardness and Rockwell
CI4200 DPA
Superficial Hardness of Metallic Materials6
E 29 Practice for Using Significant Digits in Test Data to
A Designations as defined in Classification B 224, of Coppen.
Determine Conformance with Specification’
1.2 The material may also be supplied in such other
E 53 Test Methods for Chemical Analysis of Coppe?
coppers as may be agreed upon between purchaser and
E 54 Test Methods for Chemical Analysis of Special
supplier. If a particular kind of copper is not specified, any of
Brasses and Bronzes8
the above coppers may be supplied.
E 55 Practice for Sampling Wrought Nonferrous Metals
and Alloys for Determination of Chemical Compo-
NOTE I-Material for hot forging is covered by Specification B 124.
sitions
NOTE 2-Matenal for copper bus bar, rod, and shapes is covered by
Specification B 187.
E 62 Test Methods for Chemical Analysis of Copper and
NOTE 3-A complete metric companion to Specification B 133 has
Copper Alloys (Photometric Methods)8
been developed-B 133M; therefore, no metric equivalents are pre-
E 118 Test Methods for Chemical Analysis of Copper-
sented in this specification.
Chromium Alloys8
E 478 Test Methods for Chemical Analysis of Copper
Alloyss
2. Referenced Documents
E 527 Practice for Numbering Metals and Alloys (UNS)9
2.1 The following documents of the issue in effect on date
of material purchase form a part of this specification to the
3. Ordering Information
extent referenced herein:
3.1 Orders for material under this specification shall
2.1.1 ASTM Standards:
include the following information:
B 124 Specification for Copper and Copper-Alloy Forging
3. I. 1 Quantity or weight for each size,
Rod, Bar, and Shapes4
3.1.2 Copper UNS No. (Section i),
B 170 Specification for Oxygen-Free Electrolytic Copper-
3.1.3 Form: cross section, such as round, hexagonal,
Refinery Shapes4
square, etc. (see Section 12),
B 187 Specification for Copper Bus Bar, Rod, and Shapes4
3.1.4 Temper (Sections 6, 7, and 8),
3.1.5 Diameter or distance between parallel surfaces (see
12.2),
I This specification is under the jurisdiction of ASTM Committee B-5 on
3.1.6 Length (see 12.5), or coil size (see 12.4),
Copper and Copper Alloys and is the direct responsibility of Subcommittee BO5.02
on Rod, Bar, Wire. Shapes, and Forgings.
3.1.7 Edge contours (see 12.7),
Current edition approved Dec. 15, 1993. Published February 1994. Originally
3.1.8 Resistivity, if required (see 9. I),
published as B 133 - 40 T. Last previous edition B 133 - 93.
ZFor ASME Boiler and Pressure Vessel Code applications, see related
Specification SB-133 in Section II of that Code.
Annual Book of ASTM Siandards, Vols 02.0 I and 03.0 I.
The UNS system for copper and copper alloys (see Practice E 527) is a simple
expansion of the former standard designation system accomplished by the addition Annuai Book ofASTM Siandards, Vols 02.03 and 03.01.
of a prefix “C” and a suflix “OO.” The suffix can be used to accommodate Annuai Book ofASTM Siandards, Vols 14.02. 02.03, 03.01, and 03.05
composition variations of the base alloy. Annual Book of ASTM Standards, Vol 03.05.
Annual Book of ASTM Standards, Vol 02.0 I. Annuai Book of ASTM Standards, Vols O I .O I and 02.0 I.
I

---------------------- Page: 1
...