ASTM D5579-09
(Test Method)Standard Test Method for Evaluating the Thermal Stability of Manual Transmission Lubricants in a Cyclic Durability Test
Standard Test Method for Evaluating the Thermal Stability of Manual Transmission Lubricants in a Cyclic Durability Test
SIGNIFICANCE AND USE
This test method is used to evaluate automotive manual transmission fluids for thermal instability, which results in deterioration of synchronizer performance.
This test method may also be utilized in other specifications and classifications of transmission and gear lubricants such as the following:
(final API designation of PG-1),
Military Specification MIL-L-2105,
SAE Information Report J308 Axle and Manual Transmission Lubricants, and
Mack Truck GO-H Gear Lubricant Specification.
SCOPE
1.1 This test method covers the thermal stability of fluids for use in heavy duty manual transmissions when operated at high temperatures.
1.2 The lubricant performance is measured by the number of shifting cycles that can be performed without failure of synchronization when the transmission is operated while continuously cycling between high and low range.
1.3 Correlation of test results with truck transmission service has not been established. However, the procedure has been shown to appropriately separate two transmission lubricants, which have shown satisfactory and unsatisfactory field performance in the trucks of one manufacturer.
1.4 Changes in this test method may be necessary due to refinements in the procedure, obsolescence of parts, or reagents, and so forth. These changes will be incorporated by Information Letters issued by the ASTM Test Monitoring Center (TMC). The test method will be revised to show the content of all the letters, as issued.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5.1 Exception—When materials, products, or equipment are available only in inch-pound units, SI units are omitted.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.7 This test method is arranged as follows:
Section Scope 1 Referenced Documents 2 Terminology 3 Summary of Test Method 4 Significance and Use 5 Apparatus 6 Test Transmission 6.2 Transmission Mounts 6.3 Oil-Circulating System 6.4 Oil Return Hole 6.5 Air Pressure Controls 6.6 Drive System 6.7 Instrumentation 6.8 Thermocouple Placement 6.9 Reagents and Materials 7 Safety 8 Preparation of Apparatus 9 Cleaning of Parts 9.1 Assembly 9.2 Calibration 10 Transmission and Test Stand Calibration 10.1 Reference Oils 10.2 Reference Oil Test Frequency 10.3 Instrumentation Calibration 10.4 Shift Time Calibration 10.5 Operating Procedure 11 System Flush and Charge 11.1 Test Operation 11.2 Shut-Down Procedure 11.3 Transmission Disassembly 11.4 Determination of Test Results 12 Failure Criteria 12.1 Shifter Fork Wear 12.2 Test Validity Determination 12.3 Report 14 Precision and Bias 15 Keywords 16 Test Validity Calculations and LimitsAnnex A1 Test Kit PartsAnnex A2 HTCT Test Report Forms and Data DictionaryAnnex A3 Manual Transmission Cyclic Durability Test Parts Inspection and Wear MeasurementsAnnex A4
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5579 – 09a
Standard Test Method for
Evaluating the Thermal Stability of Manual Transmission
1
Lubricants in a Cyclic Durability Test
This standard is issued under the fixed designation D5579; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
Terminology 3
Summary of Test Method 4
1.1 Thistestmethodcoversthethermalstabilityoffluidsfor
Significance and Use 5
use in heavy duty manual transmissions when operated at high
Apparatus 6
Test Transmission 6.2
temperatures.
Transmission Mounts 6.3
1.2 The lubricant performance is measured by the number
Oil-Circulating System 6.4
of shifting cycles that can be performed without failure of
Oil Return Hole 6.5
Air Pressure Controls 6.6
synchronization when the transmission is operated while con-
Drive System 6.7
tinuously cycling between high and low range.
Instrumentation 6.8
1.3 Correlation of test results with truck transmission ser- Thermocouple Placement 6.9
Reagents and Materials 7
vicehasnotbeenestablished.However,theprocedurehasbeen
Safety 8
shown to appropriately separate two transmission lubricants,
Preparation of Apparatus 9
which have shown satisfactory and unsatisfactory field perfor- Cleaning of Parts 9.1
Assembly 9.2
mance in the trucks of one manufacturer.
Calibration 10
1.4 Changes in this test method may be necessary due to
Transmission and Test Stand Calibration 10.1
refinements in the procedure, obsolescence of parts, or re- Reference Oils 10.2
Reference Oil Test Frequency 10.3
agents, and so forth. These changes will be incorporated by
Instrumentation Calibration 10.4
Information Letters issued by the ASTM Test Monitoring
Shift Time Calibration 10.5
2
Center (TMC). The test method will be revised to show the Operating Procedure 11
System Flush and Charge 11.1
content of all the letters, as issued.
Test Operation 11.2
1.5 The values stated in inch-pound units are to be regarded
Shut-Down Procedure 11.3
as standard. The values given in parentheses are mathematical Transmission Disassembly 11.4
Determination of Test Results 12
conversions to SI units that are provided for information only
Failure Criteria 12.1
and are not considered standard.
Shifter Fork Wear 12.2
Test Validity Determination 12.3
1.5.1 Exception—When materials, products, or equipment
Report 13
are available only in inch-pound units, SI units are omitted.
Precision and Bias 14
1.6 This standard does not purport to address all of the
Keywords 15
safety concerns, if any, associated with its use. It is the Test Validity Calculations and Limits Annex A1
Test Kit Parts Annex A2
responsibility of the user of this standard to establish appro-
HTCT Test Report Forms and Data Dictionary Annex A3
priate safety and health practices and determine the applica-
Manual Transmission Cyclic Durability Test Parts Annex A4
Inspection and Wear Measurements
bility of regulatory limitations prior to use.
1.7 This test method is arranged as follows:
2. Referenced Documents
Section
3
2.1 ASTM Standards:
Scope 1
Referenced Documents 2
D235 Specification for Mineral Spirits (Petroleum Spirits)
(Hydrocarbon Dry Cleaning Solvent)
E29 Practice for Using Significant Digits in Test Data to
Determine Conformance with Specifications
1
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
D02.B0.03 on Automotive Gear Lubricants & Fluids.
Current edition approved Oct. 1, 2009. Published November 2009. Originally
3
approved in 1994. Last previous edition approved in 2009 as D5579–09. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/D5579-09a. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
ASTM Test Monitoring Center, 6555 Penn Ave., Pittsburgh, PA 15206-4489. Standards volume information, refer to the standard’s Document Summary page on
This edition incorporates revisions in all Information Letters through No. 09-1. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D5579 – 09a
2.2 SAE Standard: 4.7 At the conclusion of the test, the test parts are removed
4
SAE J308 Axle and Manual Transmission Lubricants and visually inspected. The shifter fork and friction plates are
2.3 Military Standard: measured again to determine wear.
5
MIL-L-2105 Lubricating Oil, Gear, Multipurpose
5. Significance and Use
2.4 Other Standard:
6
5.1 This test method is used to evaluate automotive manual
GO-H Mack Trucks Oil,G
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D5579–06 Designation: D 5579 – 09
Standard Test Method for
Evaluating the Thermal Stability of Manual Transmission
1
Lubricants in a Cyclic Durability Test
This standard is issued under the fixed designation D 5579; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers the thermal stability of fluids for use in heavy duty manual transmissions when operated at high
temperatures.
1.2 The lubricant performance is measured by the number of shifting cycles that can be performed without failure of
synchronization when the transmission is operated while continuously cycling between high and low range.
1.3 Correlation of test results with truck transmission service has not been established. However, the procedure has been shown
to appropriately separate two transmission lubricants, which have shown satisfactory and unsatisfactory field performance in the
trucks of one manufacturer.
1.4 Changes in this test method may be necessary due to refinements in the procedure, obsolescence of parts, or reagents, and
2
so forth.These changes will be incorporated by Information Letters issued by theASTMTest Monitoring Center (TMC). The test
method will be revised to show the content of all the letters, as issued.
1.5The values stated in inch-pound units are to be regarded as standard. When materials, products, or equipment are available
only in inch-pound units, SI units are omitted.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5.1 Exception—When materials, products, or equipment are available only in inch-pound units, SI units are omitted.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.7 This test method is arranged as follows:
Section
Scope 1
Referenced Documents 2
Terminology 3
Summary of Test Method 4
Significance and Use 5
Apparatus 6
Test Transmission 6.2
Transmission Mounts 6.3
Oil-Circulating System 6.4
Oil Return Hole 6.5
Air Pressure Controls 6.6
Drive System 6.7
Instrumentation 6.8
Thermocouple Placement 6.9
Reagents and Materials 7
Safety 8
Preparation of Apparatus 9
Cleaning of Parts 9.1
Assembly 9.2
Calibration 10
Transmission and Test Stand Calibration 10.1
Reference Oils 10.2
Reference Oil Test Frequency 10.3
1
This test method is under the jurisdiction ofASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.B0.03
on Automotive Gear Lubricants & Fluids.
Current edition approved May 1, 2006.April 15, 2009. Published May 2006.June 2009. Originally approved in 1994. Last previous edition approved in 20052006 as
D 5579–056.
2
ASTM Test Monitoring Center, 6555 Penn Ave., Pittsburgh, PA 15206-4489. This edition incorporates revisions in all Information Letters through No. 05-2.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D5579–09
Instrumentation Calibration 10.4
Shift Time Calibration 10.5
Operating Procedure 11
System Flush and Charge 11.1
Test Operation 11.2
Shut-Down Procedure 11.3
Transmission Disassembly 11.4
Determination of Test Results 12
Failure Criteria 12.1
Shifter Fork Wear 12.2
Test Validity Determination 12.3
Report 13
Precision and Bias 14
Keywords 15
Test Validity Calculations and Limits Annex A1
Test Kit Parts Annex A2
HTCT Test Report Forms and Data Dictionary Annex A3
Manual Transmission Cyclic Durability Test Parts Annex A4
Inspection and Wear Measurements
2. Referenced Documents
3
2.1 ASTM Standards:
D 235 Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
2.2 SAE Standard:
4
SAE J308 Axle and Manual Transmission Lubricants
2.3 Military Standard:
5
MIL-L-2105 Lubricating Oil, Gear, Multipurpose
2.4 Other Standard:
6
GO-H Ma
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.