ASTM F1866-13
(Specification)Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings
Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings
ABSTRACT
This specification covers requirements and test methods for fabricated poly(vinyl chloride) (PVC) plastic schedule 40 drainage and DWV fittings. These fabricated fittings are manufactured from pipe, or from a combination of pipe and injection molded parts. Resistance to bending test, leak test, and solvent weld bond area test shall be performed to meet the requirements prescribed. The spigot diameter, spigot length, wall thickness, socket diameter, and socket length shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers requirements and test methods for fabricated poly(vinyl chloride) (PVC) plastic schedule 40 drainage and DWV fittings to be used with piping manufactured in accordance with Specifications D2665 or F891. These fabricated fittings are manufactured from pipe, or from a combination of pipe and injection molded parts.
1.2 The requirements of this specification are to provide fabricated PVC fittings suitable for drainage and venting of sanitary waste systems, storm water systems, and certain other liquid wastes. Fittings shall have solvent cement joints, gasket joints or a combination thereof.
1.3 The text of this specification references notes, footnotes, and appendixes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.
1.5 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1866 −13 An American National Standard
Standard Specification for
Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage
1
and DWV Fabricated Fittings
This standard is issued under the fixed designation F1866; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
Compounds and Chlorinated Poly(Vinyl Chloride)
1.1 This specification covers requirements and test methods
(CPVC) Compounds
for fabricated poly(vinyl chloride) (PVC) plastic schedule 40
D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic
drainage and DWV fittings to be used with piping manufac-
Pipe, Schedules 40, 80, and 120
tured in accordance with Specifications D2665 or F891. These
D2122 Test Method for Determining Dimensions of Ther-
fabricated fittings are manufactured from pipe, or from a
moplastic Pipe and Fittings
combination of pipe and injection molded parts.
D2564 Specification for Solvent Cements for Poly(Vinyl
1.2 The requirements of this specification are to provide
Chloride) (PVC) Plastic Piping Systems
fabricated PVC fittings suitable for drainage and venting of
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic
sanitary waste systems, storm water systems, and certain other
Drain, Waste, and Vent Pipe and Fittings
liquid wastes. Fittings shall have solvent cement joints, gasket
D2855 Practice for the Two-Step (Primer and Solvent Ce-
joints or a combination thereof.
ment) Method of Joining Poly (Vinyl Chloride) (PVC) or
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and
1.3 The text of this specification references notes, footnotes,
and appendixes that provide explanatory material. These notes Piping Components with Tapered Sockets
D3212 Specification for Joints for Drain and Sewer Plastic
and footnotes (excluding those in tables and figures) shall not
be considered as requirements of the specification. Pipes Using Flexible Elastomeric Seals
F412 Terminology Relating to Plastic Piping Systems
1.4 The values stated in inch-pound units are to be regarded
F477 Specification for Elastomeric Seals (Gaskets) for Join-
as the standard. The values given in parentheses are provided
ing Plastic Pipe
for information only.
F656 Specification for Primers for Use in Solvent Cement
1.5 The following safety hazards caveat pertains only to the
Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and
test method portion, Section 10, of this specification. This
Fittings
standard does not purport to address all of the safety concerns,
F891 Specification for Coextruded Poly(Vinyl Chloride)
if any, associated with its use. It is the responsibility of the user
(PVC) Plastic Pipe With a Cellular Core
of this standard to establish appropriate safety and health
F913 Specification for Thermoplastic Elastomeric Seals
practices and determine the applicability of regulatory limita-
(Gaskets) for Joining Plastic Pipe
tions prior to use.
3. Terminology
2. Referenced Documents
3.1 Definitions—Definitions are in accordance with Termi-
2
2.1 ASTM Standards: nology F412, and abbreviations are in accordance with Termi-
D618 Practice for Conditioning Plastics for Testing nology D1600, unless otherwise specified.
D1600 Terminology forAbbreviatedTerms Relating to Plas-
4. Materials and Manufacture
tics
4.1 Basic Materials—The molded components for fabri-
cated fittings shall be made of virgin or rework PVC com-
1
This standard is under the jurisdiction of Committee F17 on Plastic Piping pounds meeting or exceeding the requirements of Class 12454
Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
as defined in Specification D1784.
Current edition approved Aug. 1, 2013. Published August 2013. Originally
4.1.1 The pipe shall be made of PVC that meets the
approved in 1998. Last previous edition approved in 2007 as F1866–07. DOI:
requirements of the Materials Section of Specification D1785
10.1520/F1866-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
or D2665.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4.2 Gaskets—Elastomeric seals (gaskets) shall comply with
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. the requirements of Specification F477 or F913.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1866−13
4.3 Lubricant—The lubricant used for field assembly shall 6.4 Solvent Cement Socket
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1866 − 07 F1866 − 13 An American National Standard
Standard Specification for
Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage
1
and DWV Fabricated Fittings
This standard is issued under the fixed designation F1866; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers requirements and test methods for fabricated poly(vinyl chloride) (PVC) plastic schedule 40
drainage and DWV fittings to be used with piping manufactured in accordance with Specifications D2665, D1785, or F891. These
fabricated fittings are manufactured from pipe, or from a combination of pipe and injection molded parts.
1.2 The requirements of this specification are to provide fabricated PVC fittings suitable for drainage and venting of sanitary
waste systems, storm water systems, and certain other liquid wastes. Fittings shall have solvent cement joints, gasket joints or a
combination thereof.
1.3 The text of this specification references notes, footnotes, and appendixes that provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for
information only.
1.5 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification.This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D2855 Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F656 Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings
F891 Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core
F913 Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology
D1600, unless otherwise specified.
1
This standard is under the jurisdiction of Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved June 15, 2007Aug. 1, 2013. Published July 2007August 2013. Originally approved in 1998. Last previous edition approved in 20052007 as
F1866–05.–07. DOI: 10.1520/F1866-07.10.1520/F1866-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1866 − 13
4. Materials and Manufacture
4.1 Basic Materials—The molded components for fabricated fittings shall be made of virgin or rework PVC compounds meeting
or exceeding the requirements of Class 12454 as defined in Specification D1784.
4.1.1 The pipe shall be made of PVC that meets the requirements of the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.