ASTM C1613-10
(Specification)Standard Specification for Precast Concrete Grease Interceptor Tanks
Standard Specification for Precast Concrete Grease Interceptor Tanks
ABSTRACT
This specification covers design requirements, manufacturing practices, and performance requirements for monolithic or sectional precast concrete grease interceptor tanks. This standard describes precast concrete tanks installed to separate fats, oils, grease, soap scum, and other typical kitchen wastes associated with the food service industry. The different materials and manufacturing practices of precast concrete grease interceptor tanks are presented in details. Structural design of grease interceptor tanks shall be by calculation or by performance. The different structural design requirement of grease interceptor tanks includes; concrete strength, reinforcing steel placement, and openings. The different physical design requirements of grease interceptor tanks includes; capacity, shape, compartments, inlet and outlet pipes, baffles and outlet devices, and top slab openings. Testing for watertightness shall be performed using either vacuum testing or hydrostatic testing.
SCOPE
1.1 This specification covers design requirements, manufacturing practices, and performance requirements for monolithic or sectional precast concrete grease interceptor tanks.
1.2 This specification describes precast concrete tanks installed to separate fats, oils, grease, soap scum, and other typical kitchen wastes associated with the food service industry.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1613 −10
Standard Specification for
1
Precast Concrete Grease Interceptor Tanks
This standard is issued under the fixed designation C1613; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope and Plain Bars for Concrete Reinforcement
C33 Specification for Concrete Aggregates
1.1 This specification covers design requirements, manufac-
C39/C39M Test Method for Compressive Strength of Cylin-
turing practices, and performance requirements for monolithic
drical Concrete Specimens
or sectional precast concrete grease interceptor tanks.
C94/C94M Specification for Ready-Mixed Concrete
1.2 This specification describes precast concrete tanks in-
C125 Terminology Relating to Concrete and Concrete Ag-
stalled to separate fats, oils, grease, soap scum, and other
gregates
typical kitchen wastes associated with the food service indus-
C150 Specification for Portland Cement
try.
C260 Specification for Air-Entraining Admixtures for Con-
1.3 The values stated in inch-pound units are to be regarded
crete
as standard. The values given in parentheses are mathematical
C330 Specification for Lightweight Aggregates for Struc-
conversions to SI units that are provided for information only
tural Concrete
and are not considered standard.
C494/C494M Specification for Chemical Admixtures for
1.4 This standard does not purport to address all of the Concrete
safety concerns, if any, associated with its use. It is the
C595 Specification for Blended Hydraulic Cements
responsibility of the user of this standard to establish appro-
C618 Specification for Coal Fly Ash and Raw or Calcined
priate safety and health practices and determine the applica-
Natural Pozzolan for Use in Concrete
bility of regulatory limitations prior to use.
C685/C685M Specification for Concrete Made by Volumet-
ric Batching and Continuous Mixing
2. Referenced Documents
C890 Practice for Minimum Structural Design Loading for
2
2.1 ASTM Standards: Monolithic or Sectional Precast Concrete Water and
A82/A82M Specification for Steel Wire, Plain, for Concrete Wastewater Structures
Reinforcement
C923 Specification for Resilient Connectors Between Rein-
A184/A184M Specification for Welded Deformed Steel Bar
forced Concrete Manhole Structures, Pipes, and Laterals
Mats for Concrete Reinforcement
C990 Specification for Joints for Concrete Pipe, Manholes,
A185/A185M Specification for Steel Welded Wire
and Precast Box Sections Using Preformed Flexible Joint
Reinforcement, Plain, for Concrete
Sealants
A496/A496M Specification for Steel Wire, Deformed, for
C1116 Specification for Fiber-Reinforced Concrete and
Concrete Reinforcement
Shotcrete
A497/A497M Specification for Steel Welded Wire
C1602/C1602M Specification for Mixing Water Used in the
Reinforcement, Deformed, for Concrete
Production of Hydraulic Cement Concrete
A615/A615M SpecificationforDeformedandPlainCarbon-
3
2.2 ACI Standard:
Steel Bars for Concrete Reinforcement
ACI 318 Building Code Requirements for Reinforced Con-
A706/A706M Specification for Low-Alloy Steel Deformed
crete
4
2.3 IAPMO Documents:
1
This specification is under the jurisdiction ofASTM Committee C27 on Precast
Uniform Plumbing Code
ConcreteProductsandisthedirectresponsibilityofSubcommitteeC27.30onWater
IAPMO PS-80 Grease Interceptors and Clarifiers
and Wastewater Containers.
Current edition approved Jan. 1, 2010. Published January 2010. Originally
approved in 2006. Last previous edition approved in 2009 as C1613 – 09. DOI:
10.1520/C1613-10.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, Farmington
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Hills, MI 48333-9094, http://www.concrete.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from InternationalAssociation of Plumbing and Mechanical Officials
the ASTM website. (IAPMO), 5001 E. Philadelphia St., Ontario, CA 91761.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1613−10
5
2.4 AASHTO Standard: 4.1.3 Capacity of tank in gallons or litres.
Standard Specifications for Highway Bridges 4.1.4 Special cement requirements including moderate
sulfate-resisting cement, Specification C150 Type II, or highly
3. Terminology
sulfate-resisting cement, Specification C150, Type V. If the
purchaser does not stipulate, the manufacturer shall use any
3.1 For definitions of terms relating to concrete, see Termi-
cement meeting the requ
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1613–09 Designation: C1613 – 10
Standard Specification for
1
Precast Concrete Grease Interceptor Tanks
This standard is issued under the fixed designation C1613; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers design requirements, manufacturing practices, and performance requirements for monolithic or
sectional precast concrete grease interceptor tanks.
1.2 This specification describes precast concrete tanks installed to separate fats, oils, grease, soap scum, and other typical
kitchen wastes associated with the food service industry.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A82/A82M Specification for Steel Wire, Plain, for Concrete Reinforcement
A184/A184M Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement
A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete
A496/A496M Specification for Steel Wire, Deformed, for Concrete Reinforcement
A497/A497M Specification for Steel Welded Wire Reinforcement, Deformed, for Concrete
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A706/A706M Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
C33 Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C94/C94M Specification for Ready-Mixed Concrete
C125 Terminology Relating to Concrete and Concrete Aggregates
C150 Specification for Portland Cement
C260 Specification for Air-Entraining Admixtures for Concrete
C330 Specification for Lightweight Aggregates for Structural Concrete
C494/C494M Specification for Chemical Admixtures for Concrete
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C685/C685M Specification for Concrete Made by Volumetric Batching and Continuous Mixing
C890 Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater
Structures
C923 Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals
C990 Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
C1116 Specification for Fiber-Reinforced Concrete and Shotcrete
C1602/C1602M Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
3
2.2 ACI Standard:
ACI 318 Building Code Requirements for Reinforced Concrete
1
This specification is under the jurisdiction of ASTM Committee C27 on Precast Concrete Products and is the direct responsibility of Subcommittee C27.30 on Water
and Wastewater Containers.
Current edition approved Jan. 15, 2009.1, 2010. Published February 2009.January 2010. Originally approved in 2006. Last previous edition approved in 20082009 as
C1613 – 089. DOI: 10.1520/C1613-109.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington Hills, MI 48333-9094, http://www.concrete.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1613 – 10
4
2.3 IAPMO Documents:
Uniform Plumbing Code
IAPMO PS-80 Grease Interceptors and Clarifiers
5
2.4 AASHTO Standard:
Standard Specifications for Highway Bridges
3. Terminology
3.1 For definitions of terms relating to concrete, see Terminology C125.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 access opening, n—a hole in the top slab used to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.