ASTM C94/C94M-24a
(Specification)Standard Specification for Ready-Mixed Concrete
Standard Specification for Ready-Mixed Concrete
ABSTRACT
This specification covers ready-mixed concrete manufactured and delivered to a purchaser in freshly mixed and unhardened state as hereinafter specified. Requirements for quality of concrete shall be either as hereinafter specified or as specified by the purchase. In any case where the requirements of the purchaser differ from these in this specification, the purchaser's specification shall govern. In the absence of designated applicable materials specifications, materials specifications specified shall be used for cementitious materials, hydraulic cement, supplementary cementitious materials, cementitious concrete mixtures, aggregates, air-entraining admixtures, and chemical admixtures. Except as otherwise specifically permitted, cement, aggregate, and admixtures shall be measured by mass. Mixers will be stationary mixers or truck mixers. Agitators will be truck mixers or truck agitators. Test methods for compression, air content, slump, temperature shall be performed. For s strength test, at least two standard test specimens shall be made.
SCOPE
1.1 This specification covers ready-mixed concrete as defined in 3.2.2 (Note 1). Requirements for quality of ready-mixed concrete shall be either as stated in this specification or as ordered by the purchaser. When the purchaser’s requirements, as stated in the order, differ from those in this specification, the purchaser’s requirements shall govern. This specification does not cover the placement, consolidation, curing, or protection of the concrete after delivery to the purchaser.
Note 1: Concrete produced by volumetric batching and continuous mixing is covered in Specification C685/C685M. Fiber-reinforced concrete is covered in Specification C1116/C1116M.
1.2 As used throughout this specification the producer manufactures ready-mixed concrete and the purchaser buys ready-mixed concrete.
1.3 The values stated in either SI units, shown in brackets, or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged use.2)
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C94/C94M − 24a
Standard Specification for
1
Ready-Mixed Concrete
This standard is issued under the fixed designation C94/C94M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* (Warning—Fresh hydraulic cementitious mixtures are caustic
and may cause chemical burns to skin and tissue upon
1.1 This specification covers ready-mixed concrete as de-
2
prolonged use. )
fined in 3.2.2 (Note 1). Requirements for quality of ready-
1.6 This international standard was developed in accor-
mixed concrete shall be either as stated in this specification or
dance with internationally recognized principles on standard-
as ordered by the purchaser. When the purchaser’s
ization established in the Decision on Principles for the
requirements, as stated in the order, differ from those in this
Development of International Standards, Guides and Recom-
specification, the purchaser’s requirements shall govern. This
mendations issued by the World Trade Organization Technical
specification does not cover the placement, consolidation,
Barriers to Trade (TBT) Committee.
curing, or protection of the concrete after delivery to the
purchaser.
2. Referenced Documents
3
NOTE 1—Concrete produced by volumetric batching and continuous
2.1 ASTM Standards:
mixing is covered in Specification C685/C685M. Fiber-reinforced con-
C31/C31M Practice for Making and Curing Concrete Test
crete is covered in Specification C1116/C1116M.
Specimens in the Field
1.2 As used throughout this specification the producer
C33/C33M Specification for Concrete Aggregates
manufactures ready-mixed concrete and the purchaser buys
C39/C39M Test Method for Compressive Strength of Cylin-
ready-mixed concrete.
drical Concrete Specimens
C125 Terminology Relating to Concrete and Concrete Ag-
1.3 The values stated in either SI units, shown in brackets,
gregates
or inch-pound units are to be regarded separately as standard.
C138/C138M Test Method for Density (Unit Weight), Yield,
The values stated in each system may not be exact equivalents;
and Air Content (Gravimetric) of Concrete
therefore, each system shall be used independently of the other.
C143/C143M Test Method for Slump of Hydraulic-Cement
Combining values from the two systems may result in non-
Concrete
conformance with the standard.
C150/C150M Specification for Portland Cement
1.4 The text of this specification references notes and
C172/C172M Practice for Sampling Freshly Mixed Con-
footnotes that provide explanatory material. These notes and
crete
footnotes (excluding those in tables and figures) shall not be
C173/C173M Test Method for Air Content of Freshly Mixed
considered as requirements of the specification.
Concrete by the Volumetric Method
1.5 This standard does not purport to address all of the
C231/C231M Test Method for Air Content of Freshly Mixed
safety concerns, if any, associated with its use. It is the
Concrete by the Pressure Method
responsibility of the user of this standard to establish appro-
C260/C260M Specification for Air-Entraining Admixtures
priate safety, health, and environmental practices and deter-
for Concrete
mine the applicability of regulatory limitations prior to use.
C330/C330M Specification for Lightweight Aggregates for
Structural Concrete
1 2
This specification is under the jurisdiction of ASTM Committee C09 on See Section on Safety Precautions, Manual of Aggregate and Concrete Testing,
Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee Annual Book of ASTM Standards, Vol 04.02.
3
C09.40 on Ready-Mixed Concrete. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2024. Published April 2024. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1933. Last previous edition approved in 2024 as C94/C94M – 24. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C0094_C0094M-24A.
the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C94/C94M − 24a
5
C494/C494M Specification for Chemical Admixtures for 2.3 Other Documents:
Concrete NIST 105-1 National Institute of Standards
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C94/C94M − 24 C94/C94M − 24a
Standard Specification for
1
Ready-Mixed Concrete
This standard is issued under the fixed designation C94/C94M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers ready-mixed concrete as defined in 3.2.2 (Note 1). Requirements for quality of ready-mixed concrete
shall be either as stated in this specification or as ordered by the purchaser. When the purchaser’s requirements, as stated in the
order, differ from those in this specification, the purchaser’s requirements shall govern. This specification does not cover the
placement, consolidation, curing, or protection of the concrete after delivery to the purchaser.
NOTE 1—Concrete produced by volumetric batching and continuous mixing is covered in Specification C685/C685M. Fiber-reinforced concrete is covered
in Specification C1116/C1116M.
1.2 As used throughout this specification the producer manufactures ready-mixed concrete and the purchaser buys ready-mixed
concrete.
1.3 The values stated in either SI units, shown in brackets, or inch-pound units are to be regarded separately as standard. The
values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
Combining values from the two systems may result in non-conformance with the standard.
1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the specification.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns
2
to skin and tissue upon prolonged use. )
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
1
This specification is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee C09.40 on
Ready-Mixed Concrete.
Current edition approved Jan. 1, 2024April 1, 2024. Published February 2024April 2024. Originally approved in 1933. Last previous edition approved in 20232024 as
C94/C94M – 23.C94/C94M – 24. DOI: 10.1520/C0094_C0094M-24.10.1520/C0094_C0094M-24A.
2
See Section on Safety Precautions, Manual of Aggregate and Concrete Testing, Annual Book of ASTM Standards, Vol 04.02.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C94/C94M − 24a
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C33/C33M Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C125 Terminology Relating to Concrete and Concrete Aggregates
C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C150/C150M Specification for Portland Cement
C172/C172M Practice for Sampling Freshly Mixed Concrete
C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C231/C231M Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C260/C260M Specification for Air-Entraining Admixtures for Concrete
C330/C330M Specificati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.