ASTM A994-13
(Guide)Standard Guide for Editorial Procedures and Form of Product Specifications for Steel, Stainless Steel, and Related Alloys
Standard Guide for Editorial Procedures and Form of Product Specifications for Steel, Stainless Steel, and Related Alloys
SIGNIFICANCE AND USE
4.1 The Form and Style Manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee A01 recognizes the need to provide a supplementary document pertaining to the types of products and materials covered by those specifications.
4.2 This guide contains a list of sections to be considered for inclusion in a specification for steel, stainless steel, and related alloy products, and guidance or recommended wording, or both, for such sections.
4.3 Persons drafting new product specifications, or modifying existing ones, under the jurisdiction of Committee A01, should follow this guide and the requirements of the Form and Style Manual to ensure consistency.
SCOPE
1.1 This guide covers the editorial form and style for product specifications under the jurisdiction of ASTM Committee A01.Note 1—For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style for ASTM Standards (Blue Book).2
1.2 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures outlined herein, and be guided by the latest specification covering similar commodities.
1.3 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for use by the subcommittees to Committee A01. This guide is to be applied in conjunction with the Form and Style Manual.
1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of the current edition of the Form and Style Manual, the guide has precedence.
1.5 When patents are involved, the specifications writer should refer to section F3 of the Form and Style Manual. Also, refer to part F of the Form and Style Manual for trademark information and the safety hazards caveat.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A994 −13
StandardGuide for
Editorial Procedures and Form of Product Specifications for
1
Steel, Stainless Steel, and Related Alloys
This standard is issued under the fixed designation A994; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* A370 Test Methods and Definitions for Mechanical Testing
of Steel Products
1.1 This guide covers the editorial form and style for
A488/A488M Practice for Steel Castings, Welding, Qualifi-
product specifications under the jurisdiction of ASTM Com-
cations of Procedures and Personnel
mittee A01.
A700 Practices for Packaging, Marking, and Loading Meth-
NOTE 1—For standards other than product specifications, such as test
ods for Steel Products for Shipment
methods, practices, and guides, see the appropriate sections of Form and
A751 Test Methods, Practices, and Terminology for Chemi-
2
Style for ASTM Standards (Blue Book).
cal Analysis of Steel Products
1.2 Subcommittees preparing new product specifications or
A941 TerminologyRelatingtoSteel,StainlessSteel,Related
revising existing ones should follow the practices and proce-
Alloys, and Ferroalloys
dures outlined herein, and be guided by the latest specification
A1058 Test Methods for Mechanical Testing of Steel
covering similar commodities.
Products—Metric
1.3 This guide has been prepared as a supplement to the E6 Terminology Relating to Methods of Mechanical Testing
E1282 GuideforSpecifyingtheChemicalCompositionsand
current edition of the Form and Style Manual, and is appro-
priate for use by the subcommittees to Committee A01. This Selecting Sampling Practices and Quantitative Analysis
Methods for Metals, Ores, and Related Materials
guide is to be applied in conjunction with the Form and Style
4
Manual.
2.2 ASME Boiler and Pressure Vessel Codes:
Section IX Welding and Brazing Qualifications
1.4 If a conflict exists between this guide and the mandatory
sections of the current edition of the Form and Style Manual,
2.3 Federal Standard:
5
the Form and Style Manual requirements have precedence. If a
Fed. Std. No. 123 Marking for Shipments (Civil Agencies)
conflict exists between this guide and the nonmandatory
sections of the current edition of the Form and Style Manual,
3. Terminology
the guide has precedence.
3.1 Definitions of Terms Specific to This Standard:
1.5 When patents are involved, the specifications writer
3.1.1 For definitions of terms used in this guide, refer to the
should refer to section F3 of the Form and Style Manual.Also,
Form and Style Manual, Terminology A941, and Terminology
refer to part F of the Form and Style Manual for trademark
E6.
information and the safety hazards caveat.
4. Significance and Use
2. Referenced Documents
4.1 The Form and Style Manual provides mandatory re-
3
2.1 ASTM Standards:
quirements and recommended practices for the preparation and
content of ASTM specifications. In order to promote consis-
tencyinthestyleandcontentofproductspecificationsunderits
1
This guide is under the jurisdiction of ASTM Committee A01 on Steel,
jurisdiction, Committee A01 recognizes the need to provide a
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
supplementary document pertaining to the types of products
A01.91 on Editorial.
and materials covered by those specifications.
Current edition approved May 1, 2013. Published June 2013. Originally
approved in 1998. Last previous edition approved in 2012 as A994–12. DOI:
10.1520/A0994-13.
2
Available fromASTM International Headquarters, 100 Barr Harbor Drive, PO
4
Box C700, West Conshohocken, PA 19428-2959. Available from American Society of Mechanical Engineers (ASME), ASME
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.asme.org.
5
Standards volume information, refer to the standard’s Document Summary page on AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
the ASTM website. Robbins Ave., Phila., PA 19111-5094, Attn: NPODS.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A994−13
4.2 Thisguidecontainsalistofsectionstobeconsideredfor
Liquid Penetrant Test
Radiographic Test
inclusion in a specification for steel, stainless steel, and related
Ultrasonic Test
alloy products, and guidance or recommended wording, or
Eddy Current Tes
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A994 − 12 A994 − 13
Standard Guide for
Editorial Procedures and Form of Product Specifications for
1
Steel, Stainless Steel, and Related Alloys
This standard is issued under the fixed designation A994; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This guide covers the editorial form and style for product specifications under the jurisdiction of ASTM Committee A01.
NOTE 1—For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style
2
for ASTM Standards (Blue Book).
1.2 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures
outlined herein, and be guided by the latest specification covering similar commodities.
1.3 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for
use by the subcommittees to Committee A01. This guide is to be applied in conjunction with the Form and Style Manual.
1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the
Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of
the current edition of the Form and Style Manual, the guide has precedence.
1.5 When patents are involved, the specifications writer should refer to section F3 of the Form and Style Manual. Also, refer
to part F of the Form and Style Manual for trademark information and the safety hazards caveat.
2. Referenced Documents
3
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A488/A488M Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A1058 Test Methods for Mechanical Testing of Steel Products—Metric
E6 Terminology Relating to Methods of Mechanical Testing
E1282 Guide for Specifying the Chemical Compositions and Selecting Sampling Practices and Quantitative Analysis Methods
for Metals, Ores, and Related Materials
4
2.2 ASME Boiler and Pressure Vessel Codes:
Section IX Welding and Brazing Qualifications
2.3 Federal Standard:
5
Fed. Std. No. 123 Marking for Shipments (Civil Agencies)
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 For definitions of terms used in this guide, refer to the Form and Style Manual, Terminology A941, and Terminology E6.
1
This guide is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.91 on
Editorial.
Current edition approved Oct. 15, 2012May 1, 2013. Published December 2012June 2013. Originally approved in 1998. Last previous edition approved in 20112012 as
A994–11.–12. DOI: 10.1520/A0994-12.10.1520/A0994-13.
2
Available from ASTM International Headquarters, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
www.asme.org.
5
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Phila., PA 19111-5094, Attn: NPODS.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A994 − 13
4. Significance and Use
4.1 The Form and Style Manual provides mandatory requirements and recommended practices for the preparation and content
of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction,
Committee A01 recognizes the need to pr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.