Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

SCOPE
1.1 This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire) for forging, under the latest revision of each of the following ASTM specifications: A 276, A 314, A 458, A 473, A 477, A 479/A 479M, A 564/A 564M, A 565, A 582/A 582M, A 638/A 638M, A 705/A 705M, and A 831/A 831M.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.
1.3 The requirements for introduction of new materials in specifications referencing this specification are given in .
1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A 480/A 480M.
1.5 General requirements for wire products in coils are covered in Specification A 555/A 555M.
1.6 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as the standard; within the text and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.7 Unless the order specifies an "M" designation, the material shall be furnished to inch-pound units.

General Information

Status
Historical
Publication Date
09-Apr-2003
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM A484/A484M-03 - Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM A484/A484M-03 - Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: A 484/A 484M – 03
Standard Specification for
General Requirements for Stainless Steel Bars, Billets, and
1
Forgings
This standard is issued under the fixed designation A 484/A 484M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope * 2. Referenced Documents
2
1.1 This specification covers general requirements that 2.1 ASTM Standards:
shall apply to wrought stainless steel bars, shapes, forgings, A 262 Practices for Detecting Susceptibility to Intergranu-
3
and billets or other semi-finished material (except wire) for lar Attack in Austenitic Stainless Steels
3
forging, under the latest revision of each of the following A 276 Specification for Stainless Steel Bars and Shapes
ASTM specifications: A 276, A 314, A 458, A 473, A 477, A 314 Specification for Stainless Steel Billets and Bars for
3
A 479/A 479M, A 564/A 564M, A 565, A 582/A 582M, Forging
A 638/A 638M, A 705/A 705M, and A 831/A 831M. A 370 Test Methods and Definitions for Mechanical Testing
3
1.2 In the case of conflict between a requirement of a of Steel Products
product specification and a requirement of this specification, A 458 Specification for Hot-Worked, Hot-Cold-Worked,
the product specification shall prevail. In the case of conflict and Cold-Worked Alloy Steel Bars for High Strength at
4
between a requirement of the product specification or a Elevated Temperature
3
requirement of this specification and a more stringent require- A 473 Specification for Stainless Steel Forgings
ment of the purchase order, the purchase order shall prevail. A 479/A 479M Specification for Stainless Steel Bars and
3
The purchase order requirements shall not take precedence if Shapes for Use in Boilers and Other Pressure Vessels
they, in any way, violate the requirements of the product A 480/A 480M Specification for General Requirements for
specification or this specification; for example, by waiving a Flat-Rolled Stainless and Heat-Resisting Steel Plate,
3
test requirement or by making a test requirement less stringent. Sheet, and Strip
1.3 The requirements for introduction of new materials in A 555/A 555M Specification for General Requirements for
3
specifications referencing this specification are given in Annex Stainless and Heat-Resisting Steel Wire and Wire Rods
A1. A 564/A 564M Specification for Hot-Rolled and Cold-
3
1.4 General requirements for flat-rolled stainless steel prod- Finished Age-Hardening Stainless Steel Bars and Shapes
ucts other than bar are covered in Specification A 480/A 480M. A 565 Specification for Martensitic Stainless Steel Bars,
1.5 General requirements for wire products in coils are Forgings, and Forging Stock for High-Temperature Ser-
3
covered in Specification A 555/A 555M. vice
1.6 The values stated in either inch-pound units or SI A 582/A 582M Specification for Free-Machining Stainless
3
(metric) units are to be regarded separately as the standard; and Steel Bars
within the text and tables, the SI units are shown in [brackets]. A 638/A 638M Specification for Precipitation Hardening
The values stated in each system are not exact equivalents; Iron Base Superalloy Bars, Forgings, and Forging Stock
3
therefore, each system must be used independently of the other. for High-Temperature Service
Combining values from the two systems may result in noncon- A 700 Practices for Packaging, Marking, and Loading
5
formance with the specification. Methods for Steel Products for Domestic Shipment
1.7 Unless the order specifies an “M” designation, the A 705/A 705M Specification for Age-Hardening Stainless
3
material shall be furnished to inch-pound units. Steel Forgings
A 751 Test Methods, Practices, and Terminology for
3
Chemical Analysis of Steel Products
A 831/A 831M Specification for Austenitic and Martensitic
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.17 on Flat-Rolled and Wrought Stainless Steel.
Current edition approved April 10, 2003. Published May 2003. Originally
3
approved in 1963. Last previous edition approved in 2000 as A 484/A 484M – 00. Annual Book of ASTM Standards, Vol 01.03.
2 4
For ASME Boiler and Pressure Vessel Code Applications, see related Specifi- Discontinued, see 1991 Annual Book of ASTM Standards, Vol 01.05.
5
cation SA-484/SA-484M in Section II of that code. Annual Book of ASTM Standards, Vol 01.05.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Driv
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard Designation: A 484/A 484M – 03
Designation:A484/A484M–00
Standard Specification for
General Requirements for Stainless Steel Bars, Billets, and
1
Forgings
This standard is issued under the fixed designationA 484/A 484M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets
or other semi-finished material (except wire) for forging, under the latest revision of each of the following ASTM specifications:
A 276,A 314,A 458,A 473,A 477,A 479/A 479M,A 564/A 564M,A 565,A 582/A 582M,A 638/A 638M,A 705/A 705M, and
A 831/A 831M.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product
specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this
specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order
requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this
specification; for example, by waiving a test requirement or by making a test requirement less stringent.
1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1.
1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A 480/A 480M.
1.5 General requirements for wire products in coils are covered in Specification A 555/A 555M.
1.6 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as the standard; within the
text and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each
system must be used independently of the other. Combining values from the two systems may result in nonconformance with the
specification.
1.7 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.
2. Referenced Documents
2.1 ASTM Standards:
3
Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A 262
3
A 276 Specification for Stainless Steel Bars and Shapes
3
A 314 Specification for Stainless Steel Billets and Bars for Forging
3
A 370 Test Methods and Definitions for Mechanical Testing of Steel Products
A 458 Specification for Hot-Worked, Hot-Cold-Worked, and Cold-Worked Alloy Steel Bars for High Strength at Elevated
4
Temperature
3
A 473 Specification for Stainless Steel Forgings
3
A 479/A 479M Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
A 480/A 480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and
3
Strip
3
A 555/A 555M Specification for General Requirements for Stainless and Heat-Resisting Steel Wire and Wire Rods
3
A 564/A 564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
3
A 565 Specification for Martensitic Stainless Steel Bars, Forgings, and Forging Stock for High-Temperature Service
3
A 582/A 582M Specification for Free-Machining Stainless and Heat-Resisting Steel Bars
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel,Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.17 on Wrought Stainless Steel Products.
Current edition approved June 10, 2000. PublishedAugust 2000. Originally published asA484–63T. Last previous editionA484/A484M–98.on Flat-Rolled and Wrought
Stainless Steel.
Current edition approved April 10, 2003. Published May 2003. Originally approved in 1963. Last previous edition approved in 2000 as A 484/A 484M – 00.
2
For ASME Boiler and Pressure Vessel Code Applications, see related Specification SA-484/SA-484M in Section II of that code.
3
Annual Book of ASTM Standards, Vol 01.03.
4
Annual Book of ASTM Standards, Vol 03.01.
4
Discontinued, see 1991 Annual Book of ASTM Standards , Vol 01.05.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM In
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.