ASTM D5590-00(2010)
(Test Method)Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Fungal Defacement by Accelerated Four-Week Agar Plate Assay
Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Fungal Defacement by Accelerated Four-Week Agar Plate Assay
SIGNIFICANCE AND USE
Defacement of paint and coating films by fungal growth (mold, mildew) is a common phenomenon, and defacement by algal growth can also occur under certain conditions. It is generally known that differences in the environment, lighting, temperature, humidity, substrate pH, and other factors in addition to the coating composition affect the susceptibility of a given painted surface. This test method attempts to provide a means to comparatively evaluate different coating formulations for their relative performance under a given set of conditions. It does not imply that a coating that resists growth under these conditions will necessarily resist growth in the actual application.
Note 1—It is hoped that a ranking of relative performance would be similar to that ranked from outdoor exposures. However, this test method should not be used as a replacement for exterior exposure (that is, Practice D3456) since many other factors, only a few of which are listed will affect those results.
Note 2—Several companies have reported reasonable correlation of results from this test with actual use when testing film-forming, pigmented coatings. Round-robin testing of this test method versus exterior exposure is planned.
Familiarity with microbiological techniques is required. This test method should not be used by persons without at least basic microbiological training.
SCOPE
1.1 This test method covers an accelerated method for determining the relative resistance of two or more paints or coating films to fungal growth.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5590 − 00 (Reapproved2010)
Standard Test Method for
Determining the Resistance of Paint Films and Related
Coatings to Fungal Defacement by Accelerated Four-Week
1
Agar Plate Assay
This standard is issued under the fixed designation D5590; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Summary of Test Method
1.1 This test method covers an accelerated method for 3.1 This test method outlines a procedure to (1) prepare a
determining the relative resistance of two or more paints or suitable specimen for testing, (2) inoculate the specimen with
coating films to fungal growth. the proper fungal species, (3) expose the inoculated samples
under the appropriate conditions for growth, and (4) provide a
1.2 The values stated in SI units are to be regarded as the
schedule and guidelines for visual growth ratings. This test
standard. The values given in parentheses are for information
method is not designed to include all the necessary procedures
only.
to maintain the proper microbiological techniques required to
1.3 This standard does not purport to address all of the
provide the most accurate results.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
4. Significance and Use
priate safety and health practices and determine the applica-
4.1 Defacement of paint and coating films by fungal growth
bility of regulatory limitations prior to use.
(mold, mildew) is a common phenomenon, and defacement by
algal growth can also occur under certain conditions. It is
2. Referenced Documents
generally known that differences in the environment, lighting,
2
2.1 ASTM Standards:
temperature, humidity, substrate pH, and other factors in
D822 Practice for Filtered Open-Flame Carbon-Arc Expo-
addition to the coating composition affect the susceptibility of
sures of Paint and Related Coatings
a given painted surface. This test method attempts to provide a
D3273 TestMethodforResistancetoGrowthofMoldonthe
meanstocomparativelyevaluatedifferentcoatingformulations
Surface of Interior Coatings in an Environmental Cham-
for their relative performance under a given set of conditions.
ber
It does not imply that a coating that resists growth under these
D3456 Practice for Determining by Exterior Exposure Tests
conditions will necessarily resist growth in the actual applica-
theSusceptibilityofPaintFilmstoMicrobiologicalAttack
tion.
D4141 Practice for Conducting Black Box and Solar Con-
NOTE 1—It is hoped that a ranking of relative performance would be
centrating Exposures of Coatings
similar to that ranked from outdoor exposures. However, this test method
D4587 Practice for Fluorescent UV-Condensation Expo-
should not be used as a replacement for exterior exposure (that is, Practice
sures of Paint and Related Coatings
D3456) since many other factors, only a few of which are listed will affect
D5031 Practice for Enclosed Carbon-Arc Exposure Tests of
those results.
NOTE 2—Several companies have reported reasonable correlation of
Paint and Related Coatings
resultsfromthistestwithactualusewhentestingfilm-forming,pigmented
G21 Practice for Determining Resistance of Synthetic Poly-
coatings. Round-robin testing of this test method versus exterior exposure
meric Materials to Fungi
is planned.
4.2 Familiarity with microbiological techniques is required.
This test method should not be used by persons without at least
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint
basic microbiological training.
and Related Coatings, Materials, andApplications and is the direct responsibility of
Subcommittee D01.28Biodeterioration.
CurrenteditionapprovedJune1,2010.PublishedJuly2010.Originallyapproved 5. Apparatus and Materials
in 1994. Last previous edition approved in 2005 as D5590 – 00 (2005). DOI:
5.1 Balance, capable of weighing to 0.10 g.
10.1520/D5590-00R10.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.2 Incubator, or other device capable of maintaining a
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
constant temperature between 25 and 30°C, relative humidity
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. of ≤85 %.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5590 − 00 (2010)
5.3 Refrigerator, or other device capable of maintaining a 7. Preparation of the Fungal Spore Inocula
temperature of 4 6 2°C.
7.1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.