iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E305-07

(Practice)

Standard Practice for Establishing and Controlling Atomic Emission Spectrochemical Analytical Curves

Standard Practice for Establishing and Controlling Atomic Emission Spectrochemical Analytical Curves

SIGNIFICANCE AND USE
This practice is intended as a fundamental guide for the calibration, standardization, and daily control of the analytical curves for atomic emission spectrometers.
It is assumed that this practice will be used by trained operators capable of performing the procedures described herein.
SCOPE
1.1 This practice provides guidance for establishing and controlling atomic emission spectrochemical analytical curves. The generation of analytical curves and their routine control are considered as separate although interrelated operations. This practice is applicable to atomic emission spectrometers.Note 1
X-ray emission spectrometric applications are no longer covered by this practice. See Guides E 1361 and E 1621 for discussion of this technique.
1.1.1 Since computer programs are readily available to run multiple linear regressions that can be used to generate analytical curves and since most instruments include this feature, this practice does not go into detail on the procedure. However, some recommendations are given on evaluating the equations that are generated.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-May-2007
ICS
71.040.50 - Physicochemical methods of analysis
Technical Committee
E01 - Analytical Chemistry for Metals, Ores, and Related Materials
Drafting Committee
E01.20 - Fundamental Practices
Current Stage
Ref Project

Relations

Replaces
ASTM E305-89(1994)e1 - Standard Practice for Establishing and Controlling Spectrochemical Analytical Curves (Withdrawn 2005)
Effective Date
01-Jun-2007
Referred By
ASTM B954-23 - Standard Test Method for Analysis of Magnesium and Magnesium Alloys by Atomic Emission Spectrometry
Effective Date
01-Jun-2007
Referred By
ASTM E1086-22 - Standard Test Method for Analysis of Austenitic Stainless Steel by Spark Atomic Emission Spectrometry
Effective Date
01-Jun-2007
Referred By
ASTM E415-21 - Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry
Effective Date
01-Jun-2007
Referred By
ASTM E2994-21 - Standard Test Method for Analysis of Titanium and Titanium Alloys by Spark Atomic Emission Spectrometry and Glow Discharge Atomic Emission Spectrometry (Performance-Based Method)
Effective Date
01-Jun-2007
Referred By
ASTM E2209-22 - Standard Test Method for Analysis of High Manganese Steel by Spark Atomic Emission Spectrometry
Effective Date
01-Jun-2007
Referred By
ASTM E1999-23 - Standard Test Method for Analysis of Cast Iron by Spark Atomic Emission Spectrometry
Effective Date
01-Jun-2007
Referred By
ASTM C1255-18 - Standard Test Method for Analysis of Uranium and Thorium in Soils by Energy Dispersive X-Ray Fluorescence Spectroscopy
Effective Date
01-Jun-2007
Referred By
ASTM E1251-17a - Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
Effective Date
01-Jun-2007
Referred By
ASTM E1476-04(2022) - Standard Guide for Metals Identification, Grade Verification, and Sorting
Effective Date
01-Jun-2007
Referred By
ASTM E3047-22 - Standard Test Method for Analysis of Nickel Alloys by Spark Atomic Emission Spectrometry
Effective Date
01-Jun-2007
Referred By
ASTM C1271-99(2020) - Standard Test Method for X-ray Spectrometric Analysis of Lime and Limestone
Effective Date
01-Jun-2007

Buy Standard

ASTM E305-07 - Standard Practice for Establishing and Controlling Atomic Emission Spectrochemical Analytical CurvesASTM E305-07 - Standard Practice for Establishing and Controlling Atomic Emission Spectrochemical Analytical Curves
PreviousNext
Standard
ASTM E305-07 - Standard Practice for Establishing and Controlling Atomic Emission Spectrochemical Analytical Curves
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E305 − 07
StandardPractice for
Establishing and Controlling Atomic Emission
1
Spectrochemical Analytical Curves
This standard is issued under the fixed designation E305; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
3.1 For definitions of terms used in this practice, refer to
1.1 This practice provides guidance for establishing and
Terminology E135.
controlling atomic emission spectrochemical analytical curves.
The generation of analytical curves and their routine control
4. Summary of Practice
are considered as separate although interrelated operations.
4.1 Systematic and random errors that occur in obtaining
This practice is applicable to atomic emission spectrometers.
data are reviewed. Background corrections are considered as
NOTE 1—X-ray emission spectrometric applications are no longer
well as interferences from other elements. Calibration,
covered by this practice. See Guides E1361 and E1621 for discussion of
standardization, and verification procedures are discussed,
this technique.
including the use of reference materials and the generation of
1.1.1 Since computer programs are readily available to run
data. A basis is given for evaluating second, third, and higher
multiple linear regressions that can be used to generate
degree analytical curves.
analytical curves and since most instruments include this
5. Significance and Use
feature, this practice does not go into detail on the procedure.
However, some recommendations are given on evaluating the
5.1 This practice is intended as a fundamental guide for the
equations that are generated.
calibration, standardization, and daily control of the analytical
curves for atomic emission spectrometers.
1.2 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the 5.2 It is assumed that this practice will be used by trained
responsibility of the user of this standard to establish appro- operators capable of performing the procedures described
priate safety and health practices and determine the applica- herein.
bility of regulatory limitations prior to use.
6. Precautions
2. Referenced Documents 6.1 Potential Errors:
6.1.1 Bias Because of Incorrect Calibration—In the proce-
2
2.1 ASTM Standards:
dure for quantitative spectrochemical analysis, the initial gen-
E135 Terminology Relating to Analytical Chemistry for
eration of the analytical curve relates element concentration or
Metals, Ores, and Related Materials
relative concentration to spectral intensity or intensity ratio.
E1329 Practice for Verification and Use of Control Charts in
Theaccuracyofthecalibrationmaybeaffectedbyanumberof
Spectrochemical Analysis
factors, such as incorrect values for element concentrations,
E1361 Guide for Correction of Interelement Effects in
heterogeneity of the reference materials, spectral interferences,
X-Ray Spectrometric Analysis
and matrix effects. These factors may cause a shift in the
E1621 Guide for X-Ray Emission Spectrometric Analysis
analytical curve, thereby leading to bias in the analytical data
generated. It is the user’s responsibility to apply calibration
models designed to evaluate the effect of, and mathematically
1
This practice is under the jurisdiction of ASTM Committee E01 on Analytical
correct for, spectral interferences and matrix effects.
Chemistry for Metals, Ores, and Related Materials and is the direct responsibility of
6.1.1.1 Calibration bias because of incorrect element con-
Subcommittee E01.20 on Fundamental Practices.
centrations are minimized by the use of certified reference
Current edition approved June 1, 2007. Published June 2007. Originally
materials. These calibrants may be augmented with one or
approved in 1966. Discontinued March 2004 and reinstated as E305 – 07. Last
ϵ1
previous edition approved in 1994 as E305 – 89 (1994) . DOI: 10.1520/E0305-07.
more other reference materials for which the chemical compo-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
sitionshavebeencarefullydeterminedbyapprovedmethodsof
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
analysis, such as ASTM or BSI (British Standards Institute).
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. The inclusion of production materials analyzed by independent
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E305 − 07
methods permits determining whethe
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E135-23a(Terminology)
Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials

SIGNIFICANCE AND USE
3.1 Definitions given in Section 4 are intended for use in all standards on analytical chemistry for metals, ores, and related materials. The definitions should be used uniformly and consistently. The purpose of these definitions is to promote clear understanding and interpretation of the standards in which the terms are used.
SCOPE
1.1 This is a compilation of terms commonly used in analytical chemistry for metals, ores, and related materials. Terms that are generally understood or defined adequately in other readily available sources are either not included or their sources are identified.  
1.2 A definition is a single sentence with additional information included in a discussion.  
1.3 The date of last reapproval or revision of a term is in parentheses at the end of the definition.  
1.4 Definitions identical to those published by another standards organization or ASTM committee are identified with the name of the organization and the identifying document or ASTM committee and standard.  
1.5 Definitions specific to a particular field (such as emission spectrometry) are identified with an italicized introductory phrase.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E1806-23(Practice)
Standard Practice for Sampling Steel and Iron for Determination of Chemical Composition

SIGNIFICANCE AND USE
4.1 This practice covers all aspects of sampling and preparing steel and iron for chemical analysis as defined in Test Methods, Practices, and Definitions A751 and Specification A48/A48M. Such subjects as sampling location and the sampling of lots are defined.  
4.2 This practice includes most requirements for sampling steel and iron for analysis. Standard test methods that reference this practice need contain only special modifications and exceptions.  
4.3 All who use these procedures should be trained samplers capable of performing common sampling operations skillfully and safely. Only proper sampling equipment should be used.
SCOPE
1.1 This practice covers the sampling of all grades of steel, both cast and wrought, and all types (grades) of cast irons and blast furnace iron for chemical and spectrochemical determination of composition. This practice is similar to ISO 14284.  
1.2 This practice is divided into the following sections.    
Sections  
Requirements for Sampling and Sample Preparation  
6  
General  
6.1  
Sample  
6.2  
Selection of a Sample  
6.3  
Preparation of a Sample  
6.4  
Liquid Iron for Steelmaking and Pig Iron Production  
7  
General  
7.1  
Spoon Sampling  
7.2  
Probe Sampling  
7.3  
Preparation of a Sample for Analysis  
7.4  
Liquid Iron for Cast Iron Production  
8  
General  
8.1  
Spoon Sampling  
8.2  
Probe Sampling  
8.3  
Preparation of a Sample for Analysis  
8.4  
Sampling and Sample Preparation for the Determination of  
8.5  
Oxygen and Hydrogen  
Liquid Steel for Steel Production  
9  
General  
9.1  
Probe Sampling  
9.2  
Spoon Sampling  
9.3  
Preparation of a Sample for Analysis  
9.4  
Sampling and Sample Preparation for the Determination  
9.5  
of Oxygen  
Sampling and Sample Preparation for the Determination  
9.6  
of Hydrogen  
Pig Irons  
10  
General  
10.1  
Increment Sampling  
10.2  
Preparation of a Sample for Analysis  
10.3  
Cast Iron Products  
11  
General  
11.1  
Sampling and Sample Preparation  
11.2  
Sections  
Steel Products  
12  
General  
12.1  
Selection of a Laboratory Sample or a Sample for  
12.2  
Analysis from a Cast Product  
Selection of a Laboratory Sample or a Sample for  
12.3  
Analysis from a Wrought Product  
Preparation of a Sample for Analysis  
12.4  
Sampling of Leaded Steel  
12.5  
Sampling and Sample Preparation for the Determination  
12.6  
of Oxygen  
Sampling and Sample Preparation for the Determination  
12.7  
of Hydrogen  
Keywords  
13  
Annexes  
Sampling Probes for Use with Liquid Iron and Steel  
Annex A1  
Sampling Probes for Use with Liquid Steel for the  
Annex A2  
Determination of Hydrogen  
1.3 The values stated in SI units are regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific statements, see 6.4.3.5, 9.4.4.3, 12.5.1, and Section 5.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    22 pages
    English language
    sale 15% off
ASTM
ASTM E1999-23(Test Method)
Standard Test Method for Analysis of Cast Iron by Spark Atomic Emission Spectrometry

SIGNIFICANCE AND USE
5.1 The chemical composition of cast iron alloys shall be determined accurately in order to ensure the desired metallurgical properties. This procedure is suitable for manufacturing control and inspection testing.
SCOPE
1.1 This test method covers the analysis of cast iron by spark atomic emission spectrometry for the following elements in the ranges shown (Note 1):
Ranges, %  
Elements  
Applicable Range, %  
Quantitative Range, %A  
Carbon  
1.9 to 3.8  
1.90 to 3.8  
Chromium  
0 to 2.0  
0.025 to 2.0  
Copper  
0 to 0.75  
0.015 to 0.75  
Manganese  
0 to 1.8  
0.03 to 1.8  
Molybdenum  
0 to 1.2  
0.01 to 1.2  
Nickel  
0 to 2.0  
0.02 to 2.0  
Phosphorus  
0 to 0.4  
0.005 to 0.4  
Silicon  
0 to 2.5  
0.15 to 2.5  
Sulfur  
0 to 0.08  
0.01 to 0.08  
Tin  
0 to 0.14  
0.004 to 0.14  
Titanium  
0 to 0.12  
0.003 to 0.12  
Vanadium  
0 to 0.22  
0.008 to 0.22
Note 1: The ranges of the elements listed have been established through cooperative testing of reference materials. These ranges can be extended by the use of suitable reference materials.  
1.2 This test method covers analysis of specimens having a diameter adequate to overlap the bore of the spark stand opening (to effect an argon seal). The specimen thickness should be sufficient to prevent overheating during excitation. A heat sink backing may be used. The maximum thickness is limited only by the height that the stand will permit.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E1621-22(Guide)
Standard Guide for Elemental Analysis by Wavelength Dispersive X-Ray Fluorescence Spectrometry

SIGNIFICANCE AND USE
5.1 X-ray fluorescence spectrometry can provide an accurate determination of metallic and many non-metallic elements in a wide variety of solid and liquid materials. This guide covers the information that should be included in an X-ray spectrometric analytical method and provides direction to the user for determining the optimum conditions needed to achieve acceptable accuracy.  
5.2 The accuracy of a determination is a function of the calibration algorithm, the sample preparation, and the sample homogeneity. Close attention to all aspects of these areas is necessary to achieve acceptable results.  
5.3 All concepts discussed in this guide are explored in detail in a number of published texts and in the scientific literature.
SCOPE
1.1 This standard provides guidelines for developing and describing analytical procedures using a wavelength dispersive X-ray spectrometer for elemental analysis of solid metals, ores, and related materials. Material forms discussed herein include solids, powders, and solid forms prepared by chemical and physical processes such as borate fusion and pressing of briquettes.  
1.2 Liquids are not discussed in this guide because they are much less frequently encountered in metals and mining laboratories. However, aqueous liquids can be processed by borate fusion to create solid specimens, and X-ray spectrometers can be equipped to handle liquids directly.  
1.3 Some provisions of this guide may be applicable to the use of an energy dispersive X-ray spectrometer.  
1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    9 pages
    English language
    sale 15% off
  • Guide
    9 pages
    English language
    sale 15% off
ASTM
ASTM E2857-22(Guide)
Standard Guide for Validating Analytical Methods

SIGNIFICANCE AND USE
4.1 Method validation is a process of demonstrating that the method meets the required performance capabilities. International standards such as ISO/IEC 17025, certifying bodies, and regulatory agencies require evidence that analytical methods are capable of producing valid results. This applies to laboratories using published standard test methods, modified standard test methods, and in-house test methods.  
4.2 Although a collaborative study is part of this guide, this guide may be used by a single laboratory for method validation when a formal collaboration study is not practical. This guide may also be applied before a full collaboration study to predict the reliability of the method.  
4.3 The use of multiple validation techniques described in this guide increases confidence in the validity or application of the method.  
4.4 It is beyond the scope of this guide to describe fully the fundamental considerations in Section 5. For a more descriptive definition of these concepts, refer to the International Union of Pure and Applied Chemistry (IUPAC) technical report, “Harmonized Guidelines for Single Laboratory Validation of Methods of Analysis” (1), the IUPAC Compendium of Analytical Nomenclature (Orange Book) (2), and the Eurachem publication, The Fitness for Purpose of Analytical Methods, A Laboratory Guide to Method Validation and Related Topics (3).
SCOPE
1.1 This guide describes procedures for the validation of chemical and spectrochemical analytical test methods that are used by a metals, ores, and related materials analysis laboratory.  
1.2 This guide may be applied to the validation of laboratory developed (in-house) methods, addition of analytes to an existing standard test method, variation or scope expansion of an existing standard method, or the use of new or different laboratory equipment.  
1.3 The suggested approaches in this guide may also be used to validate the implementation of standard test methods used routinely by laboratories of the mining, ore processing, and metals industry.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2371-21a(Test Method)
Standard Test Method for Analysis of Titanium and Titanium Alloys by Direct Current Plasma and Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Test Methodology)

SIGNIFICANCE AND USE
5.1 This test method for the chemical analysis of titanium and titanium alloys is primarily intended to test material for compliance with specifications of chemical composition such as those under the jurisdiction of ASTM Committee B10. It may also be used to test compliance with other specifications that are compatible with the test method.  
5.2 It is assumed that all who use this test method will be trained analysts capable of performing common laboratory procedures skillfully and safely and that the work will be performed in a properly equipped laboratory.  
5.3 This is a performance-based test method that relies more on the demonstrated quality of the test result than on strict adherence to specific procedural steps. It is expected that laboratories using this test method will prepare their own work instructions. These work instructions will include detailed operating instructions for the specific laboratory, the specific reference materials used, and performance acceptance criteria. It is also expected that, when applicable, each laboratory will participate in proficiency test programs, such as described in Practice E2027, and that the results from the participating laboratory will be satisfactory.
SCOPE
1.1 This method describes the analysis of titanium and titanium alloys, such as specified by committee B10, by inductively coupled plasma atomic emission spectrometry (ICP-AES) and direct current plasma atomic emission spectrometry (DCP-AES) for the following elements:    
Element  
Application
Range (wt.%)  
Quantitative
Range (wt.%)  
Aluminum  
0–8  
0.009 to 8.0  
Boron  
0–0.04  
0.0008 to 0.01  
Cobalt  
0-1  
0.006 to 0.1  
Chromium  
0–5  
0.005 to 4.0  
Copper  
0–0.6  
0.004 to 0.5  
Iron  
0–3  
0.004 to 3.0  
Manganese  
0–0.04  
0.003 to 0.01  
Molybdenum  
0–8  
0.004 to 6.0  
Nickel  
0–1  
0.001 to 1.0  
Niobium  
0-6  
0.008 to 0.1  
Palladium  
0-0.3  
0.02 to 0.20  
Ruthenium  
0-0.5  
0.004 to 0.10  
Silicon  
0–0.5  
0.02 to 0.4  
Tantalum  
0-1  
0.01 to 0.10  
Tin  
0–4  
0.02 to 3.0  
Tungsten  
0-5  
0.01 to 0.10  
Vanadium  
0–15  
0.01 to 15.0  
Yttrium  
0–0.04  
0.001 to 0.004  
Zirconium  
0–5  
0.003 to 4.0  
1.2 This test method has been interlaboratory tested for the elements and ranges specified in the quantitative range part of the table in 1.1. It may be possible to extend this test method to other elements or broader mass fraction ranges as shown in the application range part of the table above provided that test method validation is performed that includes evaluation of method sensitivity, precision, and bias. Additionally, the validation study shall evaluate the acceptability of sample preparation methodology using reference materials or spike recoveries, or both. Guide E2857 provides information on validation of analytical methods for alloy analysis.  
1.3 Because of the lack of certified reference materials (CRMs) containing bismuth, hafnium, and magnesium, these elements were not included in the scope or the interlaboratory study (ILS). It may be possible to extend the scope of this test method to include these elements provided that method validation includes the evaluation of method sensitivity, precision, and bias during the development of the testing method.  
1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific safety hazards statements are given in Section 9.  
1.6 This international standard was developed in accordance with internationally recognized principle...

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM E1898-21(Test Method)
Standard Test Method for Determination of Silver in Copper Concentrates by Flame Atomic Absorption Spectrometry

SIGNIFICANCE AND USE
5.1 In the primary metallurgical processes used by the mineral processing industry for copper bearing ores, copper and silver associated with sulfide mineralization are concentrated by the process of flotation for recovery of the metals.  
5.2 This test method is a comparative method and is intended to be a referee method for compliance with compositional specifications for metal content or to monitor processes.  
5.3 It is assumed that all who use this method will be trained analysts capable of performing skillfully and safely. It is expected that work will be performed in a properly equipped laboratory and that proper waste disposal procedures will be followed. Appropriate quality control practices must be followed such as those described in Guide E882.
SCOPE
1.1 This test method covers the determination of silver in the range of 13 μg/g to 500 μg/g by acid dissolution of the silver and measurement by atomic absorption spectrometry. Copper concentrates are internationally traded within the following content ranges:    
Element  
Unit  
Content Range  
Aluminum  
%  
0.05  
to  
2.50  
Antimony  
%  
0.0001  
to  
4.50  
Arsenic  
%  
0.01  
to  
0.50  
Barium  
%  
0.003  
to  
0.10  
Bismuth  
%  
0.001  
to  
0.16  
Cadmium  
%  
0.0005  
to  
0.04  
Calcium  
%  
0.05  
to  
4.00  
Carbon  
%  
0.10  
to  
0.90  
Chlorine  
%  
0.001  
to  
0.006  
Chromium  
%  
0.0001  
to  
0.10  
Cobalt  
%  
0.0005  
to  
0.20  
Copper  
%  
10.0  
to  
44.0  
Fluorine  
%  
0.001  
to  
0.10  
Gold  
μg/g  
1.40  
to  
100.0  
Iron  
%  
12.0  
to  
30.0  
Lead  
%  
0.01  
to  
1.40  
Magnesium  
%  
0.02  
to  
2.00  
Manganese  
%  
0.009  
to  
0.10  
Mercury  
μg/g  
0.05  
to  
50.0  
Molybdenum  
%  
0.002  
to  
0.25  
Nickel  
%  
0.0001  
to  
0.08  
Silicon  
%  
0.40  
to  
20.0  
Silver  
μg/g  
18.0  
to  
8000  
Sulfur  
%  
10.0  
to  
36.0  
Tin  
%  
0.004  
to  
0.012  
Zinc  
%  
0.005  
to  
4.30  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E1805-21(Test Method)
Standard Test Method for Determination of Gold in Copper Concentrates by Fire Assay Gravimetry

SIGNIFICANCE AND USE
5.1 In the metallurgical process used in the mining industries, gold is often carried along with copper during the flotation concentration process. Metallurgical accounting, process control, and concentrate evaluation procedures for this type of material depend on an accurate, precise measurement of the gold in the copper concentrate. This test method is intended to be a reference method for metallurgical laboratories and a referee method to settle disputes in commercial transactions. It is also a definitive method intended to test materials for compliance with compositional specifications and to provide data for certification of reference materials. It is essential that each performance of the method be validated by applying it to appropriate reference materials at the same time and in the same manner as it is applied to the unknowns.  
5.2 It is assumed that all who use this test method will be trained analysts capable of performing skillfully and safely. It is expected that the work will be performed in a properly equipped laboratory under appropriate quality control practices such as those described in Guide E882.
SCOPE
1.1 This test method is for the determination of gold in copper concentrates in the content range from 0.2 μg/g to 17 μg/g.
Note 1: The lower scope limit is set in accordance with Practice E1601.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 11.3.1, 11.5.4, and 11.6.5.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E508-21(Test Method)
Standard Test Method for Determination of Calcium and Magnesium in Iron Ores by Flame Atomic Absorption Spectrometry

SIGNIFICANCE AND USE
5.1 This test method is intended as a referee method for compliance with compositional specifications for impurity content. It is assumed that all who use this procedure will be trained analysts capable of performing common laboratory practices skillfully and safely. It is expected that work will be performed in a properly equipped laboratory and that proper waste disposal procedures will be followed. Follow appropriate quality control practices such as those described in Guide E882.
SCOPE
1.1 This test method covers the determination of calcium and magnesium in iron ores, concentrates, and agglomerates in the mass fraction (%) range from 0.05 % to 5 % of calcium and 0.05 % to 3 % of magnesium.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E507-21(Test Method)
Standard Test Method for Determination of Aluminum in Iron Ores by Flame Atomic Absorption Spectrometry

SIGNIFICANCE AND USE
5.1 This test method is intended as a referee method for compliance with compositional specifications for impurity content. It is assumed that all who use this procedure will be trained analysts capable of performing common laboratory practices skillfully and safely. It is expected that work will be performed in a properly equipped laboratory and that proper waste disposal procedures will be followed. Follow appropriate quality control practices such as those described in Guide E882.
SCOPE
1.1 This test method covers the determination of aluminum in iron ores, concentrates, and agglomerates in the mass fraction (%) range from 0.1 to 5.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off