Standard Specification for Calcium Hypochlorite

ABSTRACT
This specification covers technical-grade calcium hypochlorite in granular form. Sampled specimens shall be tested and conform accordingly to chemical and physical requirements such as available chlorides, moisture content, and particle sizes through a U.S. 14 and U.S. 100 mesh.
SCOPE
1.1 This specification covers technical-grade calcium hypochlorite in granular form.  
1.2 The following applies to all specified limits in this specification: for purposes of determining conformance with this specification, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.4 Review the current Safety Data Sheets (SDS) for detailed information concerning toxicity, first aid procedures, handling and safety precautions.  
1.5 The following safety hazards caveat pertains only to the test methods listed in Sections 3 – 5. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-May-2021
Current Stage
Ref Project

Buy Standard

Technical specification
ASTM E1229-21 - Standard Specification for Calcium Hypochlorite
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM E1229-21 - Standard Specification for Calcium Hypochlorite
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: E1229 −21
Standard Specification for
1
Calcium Hypochlorite
This standard is issued under the fixed designation E1229; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D2022 Test Methods of Sampling and ChemicalAnalysis of
Chlorine-Containing Bleaches
1.1 This specification covers technical-grade calcium hy-
E29 Practice for Using Significant Digits in Test Data to
pochlorite in granular form.
Determine Conformance with Specifications
1.2 The following applies to all specified limits in this
2.2 Other Documents:
specification: for purposes of determining conformance with
CFR 49, Parts 100 to 199, Department of Transportation,
this specification, an observed value or a calculated value shall
Rules and Regulations for the Transportation of Hazard-
3
be rounded off “to the nearest unit” in the last right-hand digit
ous Materials
used in expressing the specification limit, in accordance with
FederalSpecificationPPP-C-2020A Chemicals,Liquid,Dry,
4
the rounding-off method of Practice E29.
and Paste, Packaging of (superseding PPP-C-2020)
1.3 Units—The values stated in SI units are to be regarded
3. Requirements
as standard. The values given in parentheses are for informa-
3.1 Technical-grade granular calcium hypochlorite shall
tion only.
conform to the following chemical and physical requirements:
1.4 Review the current Safety Data Sheets (SDS) for de-
Property Specification ASTM Test
tailed information concerning toxicity, first aid procedures,
Method
handling and safety precautions.
Available Chloride, mass % 65.0 min D2022
1.5 The following safety hazards caveat pertains only to the
(m/m)
test methods listed in Sections3–5. This standard does not
Moisture, mass % 5.5 to 10.0 D2022
(m/m)
purport to address all of the safety concerns, if any, associated
Particle Size,
with its use. It is the responsibility of the user of this standard
through U.S. 14 mesh, min % 75.0 D1921
to establish appropriate safety, health, and environmental
through U.S. 100 mesh, max % 10.0 D1921
(Method B)
practices and determine the applicability of regulatory limita-
tions prior to use.
4. Sampling
1.6 This international standard was developed in accor-
4.1 Sample technical-grade granular calcium hypochlorite
dance with internationally recognized principles on standard-
in accordance with the appropriate section of Test Methods
ization established in the Decision on Principles for the
D2022.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
5. Test Methods
Barriers to Trade (TBT) Committee.
5.1 Test each composite sample for the chemical and
physical requirements listed in Section 3.
2. Referenced Documents
2
6. Packaging and Labeling
2.1 ASTM Standards:
D1921 Test Methods for Particle Size (Sieve Analysis) of
6.1 Industrial or commercial quantities shall be packaged
Plastic Materials
and labeled in accordance with DOT Hazardous Materials
Regulations CFR 49, Parts 1
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E1229 − 16 E1229 − 21
Standard Specification for
1
Calcium Hypochlorite
This standard is issued under the fixed designation E1229; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers technical-grade calcium hypochlorite in granular form.
1.2 The following applies to all specified limits in this specification: for purposes of determining conformance with this
specification, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used
in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
1.3 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4 Review the current Safety Data Sheets (SDS) for detailed information concerning toxicity, first aid procedures, handling and
safety precautions.
1.5 The following safety hazards caveat pertains only to the test methods listed in Sections 3 – 5. This standard does not purport
to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish
appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1921 Test Methods for Particle Size (Sieve Analysis) of Plastic Materials
D2022 Test Methods of Sampling and Chemical Analysis of Chlorine-Containing Bleaches
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
2.2 Other Documents:
3
CFR 49, Parts 100 to 199, Department of Transportation, Rules and Regulations for the Transportation of Hazardous Materials
4
Federal Specification PPP-C-2020A Chemicals, Liquid, Dry, and Paste, Packaging of (superseding PPP-C-2020)
1
This specification is under the jurisdiction of ASTM Committee D16 on Aromatic, Industrial, Specialty and Related Chemicals and is the direct responsibility of
Subcommittee D16.13 on Chlorine.
Current edition approved Nov. 1, 2016June 1, 2021. Published November 2016July 2021. Originally approved in 1989. Last previous edition approved in 20082016 as
E1229E1229 – 16. – 08. DOI: 10.1520/E1229-16.10.1520/E1229-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The Code of Federal Regulations may be obtained from the U.S. Government Printing Office, 732 N. Capitol St., NW, Washington, DC 20401, http://www.gpoaccess.gov/
CFR/index.html.
4
Single copies of Federal Specifications required for bidding purposes are available without charge from General Services Administration Business Service Centers in
Boston, MA; New York, NY; Washington, DC; Philadelphia, PA; Atlanta, GA; Chicago, IL; Kansas City, MO; Forth Worth, TX; Houston, TX; Denver, CO; San Francisco,
CA; Los Angeles, CA; and Seattle, WA.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E1229 − 21
3. Requirements
3.1 Technical-grade granular calcium hypochlorite shall conform to the following chemical and physical requirements:
ASTM Test
Methods
Property Specification ASTM Test
Method
Available Chloride, % mass 65.0 min D2022
(m/m) (% by wt)
Available Chloride, mass % 65.0 min D2022
(m/m)
Moisture, % mass 5.5 to 10.0 D2022
(m/m) (% by wt)
Moisture, mass % 5.5 to 10.0 D2022
(m/m)
Particle Size,
through U.S. 14 mesh, min % 75.0 D1921
through U.S. 100 mesh, max % 10.0 D1921
(Method B)
4. Sampling
4.1 Sample technical-grade granular calcium hypochlorite in accordance with the appropriate section of Test Methods D2022.
5. Test Methods
5.1 Test
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.