ASTM F1700-13

Standard Specification for Solid Vinyl Floor Tile

ABSTRACT
This specification establishes the material and performance characteristics that determine serviceability and recommended applicability of solid vinyl floor tiles intended for use in commercial, light commercial, and residential buildings. Floor tiles shall be classified as Class I for monolithic vinyl tiles, Class II for surface-decorated vinyl tiles, and Class III for printed film vinyl tiles. Furthermore, these classes of tiles shall be subgrouped as Type A for tiles with smooth surfaces, and Type B for those with embossed surfaces. The tiles shall be composed of binder, filler, and pigments compounded with suitable lubricants and processing aids, the composition for all of which shall be dictated by their respective classes. When tested, the tiles shall adhere to the following physical requirements: binder content; dimension including size, thickness, squareness, and dimensional stability; residual indentation; flexibility; resistance to chemicals such as white vinegar, rubbing alcohol, white mineral oil, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, household bleach, olive oil, kerozene, unleaded gasoline, and phenol; resistance to heat; and resistance to light.
SCOPE
1.1 This specification covers solid vinyl2 floor tiles that are monolithic, surface decorated or printed, and protected by a clear wear layer.  
1.2 This type of floor covering is intended for use in commercial, light commercial, and residential buildings. General information and performance characteristics which determine serviceability and recommended use are included in this specification.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

General Information

• Status: Historical
• Publication Date: 31-Mar-2013
• ICS: 83.080.20 - Thermoplastic materials
• ICS: 91.060.30 - Ceilings. Floors. Stairs
• Technical Committee: F06 - Resilient Floor Coverings
• Drafting Committee: F06.80 - Specifications

Relations

• Replaces: ASTM F1700-04(2010) - Standard Specification for Solid Vinyl Floor Tile
• Effective Date: 01-Apr-2013
• Replaced By: ASTM F1700-13a - Standard Specification for Solid Vinyl Floor Tile
• Effective Date: 01-Jun-2013
• Referred By: ASTM F141-12(2020) - Standard Terminology Relating to Resilient Floor Coverings
• Effective Date: 01-Apr-2013
• Referred By: ASTM F1914-18 - Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering
• Effective Date: 01-Apr-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1700 −13
StandardSpecification for
1
Solid Vinyl Floor Tile
This standard is issued under the fixed designation F1700; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope F1514 TestMethodforMeasuringHeatStabilityofResilient
2 Flooring by Color Change
1.1 This specification covers solid vinyl floor tiles that are
F1515 Test Method for Measuring Light Stability of Resil-
monolithic, surface decorated or printed, and protected by a
ient Flooring by Color Change
clear wear layer.
F1914 Test Methods for Short-Term Indentation and Re-
1.2 This type of floor covering is intended for use in
sidual Indentation of Resilient Floor Covering
commercial, light commercial, and residential buildings. Gen-
F2055 Test Method for Size and Squareness of Resilient
eral information and performance characteristics which deter-
Floor Tile by Dial Gage Method
mine serviceability and recommended use are included in this
F2199 Test Method for Determining Dimensional Stability
specification.
of Resilient Floor Tile after Exposure to Heat
1.3 This standard does not purport to address all of the
2.2 Other Standards:
safety concerns, if any, associated with its use. It is the
ANSI/ASQC Z1.4–1993 Sampling Procedures and Tables
4
responsibility of the user of this standard to establish appro-
for Inspection by Attributes
priate safety and health practices and determine the applica-
3. Classification
bility of regulatory limitations prior to use.
1.4 The values stated in inch-pound units are to be regarded
3.1 The vinyl floor tiles covered by this specification shall
as standard. The values given in parentheses are mathematical
be classified as follows:
conversions to SI units that are provided for information only
3.1.1 Class I—Monolithic Vinyl Tile.
and are not considered standard.
3.1.1.1 Type A—Smooth Surface.
3.1.1.2 Type B—Embossed Surface.
2. Referenced Documents
3.1.2 Class II—Surface-Decorated Vinyl Tile.
3
2.1 ASTM Standards:
3.1.2.1 Type A—Smooth Surface.
F137 Test Method for Flexibility of Resilient Flooring Ma-
3.1.2.2 Type B—Embossed Surface.
terials with Cylindrical Mandrel Apparatus
3.1.3 Class III—Printed Film Vinyl Tile.
F141 Terminology Relating to Resilient Floor Coverings
3.1.3.1 Type A—Smooth Surface.
F373 Test Method for Embossed Depth of Resilient Floor
3.1.3.2 Type B—Embossed Surface.
Coverings
3.2 The embossed surfaces may or may not be grouted with
F386 Test Method for Thickness of Resilient Flooring Ma-
ink.
terials Having Flat Surfaces
F410 Test Method for Wear Layer Thickness of Resilient
4. Ordering Information
Floor Coverings by Optical Measurement
4.1 The purchaser shall state whether this specification is to
F925 Test Method for Resistance to Chemicals of Resilient
be used, select the preferred options permitted herein, and
Flooring
include the following contract requirements on the purchase
order:
1
This specification is under the jurisdiction of ASTM Committee F06 on
4.1.1 Title, number, and date of this specification,
Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.80
4.1.2 Class, type, and pattern number (Section 3),
on Specifications.
Current edition approved April 1, 2013. Published April 2013. Originally
4.1.3 Quantity in square feet, pieces, or cartons,
approvedin1996.Lastpreviouseditionapprovedin2010asF1700–04(2010).DOI:
4.1.4 Size required (Section 6),
10.1520/F1700-13.
2 4.1.5 Thickness required (Section 6),
For solid vinyl definition, refer to Terminology F141.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute, 11 West 42nd St., New
the ASTM website. York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1700−13
4.1.6 Lot formation if other than as specified in ANSI/ layer or base layer. Other base layers may be added. Each ply
ASQC Z1.4–1993 (see Sections 8 and 10), or layer will comply with Table 1 for binder content.
4.1.7 Sampling if other than as specified in ANSI/ASQC 5.5.1 For commercial applications, the wear layer shall be a
Z1.4–1993 (see Sections 8 and 10), minimum of 0.020 in. (0.50 mm) thick.
4.1.8 Packingrequirementifotherthanasspecified(Section
6. Physical Requirements
12),
4.1.9 Palletization if
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1700 − 04 (Reapproved 2010) F1700 − 13
Standard Specification for
1
Solid Vinyl Floor Tile
This standard is issued under the fixed designation F1700; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
2
1.1 This specification covers solid vinyl floor tiles that are monolithic, surface decorated or printed, and that have binder
contents referenced in protected by a clear wear layer.Table 1.
1.2 This type of floor covering is intended for use in commercial, light commercial, and residential buildings. General
information and performance characteristics which determine serviceability and recommended use are included in this
specification.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
3
2.1 ASTM Standards:
F137 Test Method for Flexibility of Resilient Flooring Materials with Cylindrical Mandrel Apparatus
F141 Terminology Relating to Resilient Floor Coverings
F373 Test Method for Embossed Depth of Resilient Floor Coverings
F386 Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces
F410 Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement
F925 Test Method for Resistance to Chemicals of Resilient Flooring
F1514 Test Method for Measuring Heat Stability of Resilient Flooring by Color Change
F1515 Test Method for Measuring Light Stability of Resilient Flooring by Color Change
F1914 Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering
F2055 Test Method for Size and Squareness of Resilient Floor Tile by Dial Gage Method
F2199 Test Method for Determining Dimensional Stability of Resilient Floor Tile after Exposure to Heat
2.2 Other Standards:
4
ANSI/ASQC Z1.4–1993 Sampling Procedures and Tables for Inspection by Attributes
3. Classification
3.1 The vinyl floor tiles covered by this specification shall be classified as follows:
3.1.1 Class I—Monolithic Vinyl Tile.
3.1.1.1 Type A—Smooth Surface.
3.1.1.2 Type B—Embossed Surface.
3.1.2 Class II—Surface-Decorated Vinyl Tile.
3.1.2.1 Type A—Smooth Surface.
1
This specification is under the jurisdiction of ASTM Committee F06 on Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.80 on
Specifications.
Current edition approved Dec. 1, 2010April 1, 2013. Published December 2010April 2013. Originally approved in 1996. Last previous edition approved in 20042010 as
F1700F1700–04(2010).–04. DOI: 10.1520/F1700-04R10.10.1520/F1700-13.
2
For solid vinyl definition, refer to Terminology F141.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American National Standards Institute, 11 West 42nd St., New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1700 − 13
TABLE 1 Minimum Binder Content
Class I Class II Class III
Each ply or layer 34 % 34 % . . .
Clear wear layer . . . . . . 90 %
Intermediate colored layer . . . . . . 34 %
Each base layer . . . . . . 34 %
3.1.2.2 Type B—Embossed Surface.
3.1.3 Class III—Printed Film Vinyl Tile.
3.1.3.1 Type A—Smooth Surface.
3.1.3.2 Type B—Embossed Surface.
3.2 The embossed surfaces may or may not be grouted with ink.
4. Ordering Information
4.1 The purchaser shall state whether this specification is to be used, select the preferred options permitted herein, and include
the following contract requirements on the purchase order:
4.1.1 Title, number, and date of this specification,
4.1.2 Class, type, and pattern number (Section 3),
4.1
...