iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5370-06(2013)

(Specification)

Standard Specification for Pozzolanic Blended Materials in Construction Applications

Standard Specification for Pozzolanic Blended Materials in Construction Applications

ABSTRACT
This specification covers Pozzolanic blended material for use in construction applications where the properties similar to finely divided mineral admixtures is present. The types of Pozzolanic blended materials covered by this specification are an intimate and uniform blend of two or more of the following materials: Type F - Class F fly ash; Type C - Class C fly ash; Type CKD - Cement kiln dust; Type S - ground granulated blast furnace slag; Type SF - Silica fume; Type M - Metakaolin. Materials shall be tested and the individual grades shall conform to specified requirements of blended Pozzolan for use with lime, and blended Pozzolan for use in concrete, detailed in this specification.
SCOPE
1.1 This specification covers pozzolanic blended material for use in construction applications where the properties normally attributed to finely divided mineral admixtures may be desired.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Aug-2013
ICS
91.100.15 - Mineral materials and products
Technical Committee
D34 - Waste Management
Drafting Committee
D34.03 - Treatment, Recovery and Reuse
Current Stage
Ref Project

Relations

Replaces
ASTM D5370-06 - Standard Specification for Pozzolanic Blended Materials in Construction Applications
Effective Date
01-Sep-2013

Buy Standard

ASTM D5370-06(2013) - Standard Specification for Pozzolanic Blended Materials in Construction ApplicationsASTM D5370-06(2013) - Standard Specification for Pozzolanic Blended Materials in Construction Applications
PreviousNext
Technical specification
ASTM D5370-06(2013) - Standard Specification for Pozzolanic Blended Materials in Construction Applications
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D5370 −06(Reapproved 2013)
Standard Specification for
1
Pozzolanic Blended Materials in Construction Applications
This standard is issued under the fixed designation D5370; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 cement kiln dust—the finely divided particulate matter
carried from a cement kiln by the exhaust gases.
1.1 This specification covers pozzolanic blended material
3.1.2 pozzolanic blended material—a pozzolan resulting
for use in construction applications where the properties
from the intimate and uniform blend of two or more finely
normally attributed to finely divided mineral admixtures may
divided materials.
be desired.
3.2 Definitions—Other terms used in this specification are
1.2 The values stated in SI units are to be regarded as the
definedinTerminologiesC125orC219orSpecificationC618.
standard. The values given in parentheses are for information
only.
4. Classification
1.3 This standard does not purport to address all of the
4.1 The types of pozzolanic blended materials covered by
safety concerns, if any, associated with its use. It is the
this specification are an intimate and uniform blend of two or
responsibility of the user of this standard to establish appro-
moreofthefollowingmaterials:TypeF–ClassFflyash;Type
priate safety and health practices and determine the applica-
C – Class C fly ash; Type CKD – Cement kiln dust; Type S –
bility of regulatory limitations prior to use.
ground granulated blast furnace slag; Type SF – Silica fume;
Type M – Metakaolin.
2. Referenced Documents
2
2.1 ASTM Standards: 4.2 The blended pozzolan shall be labeled in order of
highest mass of materials. For example, a 60 % by mass Class
C25Test Methods for Chemical Analysis of Limestone,
Quicklime, and Hydrated Lime Fflyashwith30%bymassslagand10%bymasscementkiln
dust would be termed Type FSCKD.
C125Terminology Relating to Concrete and Concrete Ag-
gregates
5. Ordering Information
C219Terminology Relating to Hydraulic Cement
C311Test Methods for Sampling and Testing Fly Ash or 5.1 Include the following information in orders for blended
Natural Pozzolans for Use in Portland-Cement Concrete pozzolan meeting the requirements of this specification:
C593SpecificationforFlyAshandOtherPozzolansforUse 5.1.1 The specification designation ASTM Specification
With Lime for Soil Stabilization D5370,
C618Specification for Coal Fly Ash and Raw or Calcined 5.1.2 The specification date, if other than the latest pub-
Natural Pozzolan for Use in Concrete lished version,
3
5.1.3 The quantity of blended pozzolan desired, and the
2.2 EPA Standard:
classification desired,
EPA 9060Total Organic Carbon
5.1.4 A statement as to specific requirements or intended
3. Terminology
use of the blended pozzolan, and
5.1.5 Request for the manufacturers certification, if desired.
3.1 Definitions of Terms Specific to This Standard:
6. Materials and Manufacturer
1
This specification is under the jurisdiction ofASTM Committee D34 on Waste
6.1 The pozzolanic blended material is the result of an
ManagementandisthedirectresponsibilityofSubcommitteeD34.03onTreatment,
intimate and uniform blend.
Recovery and Reuse.
Current edition approved Sept. 1, 2013. Published September 2013. Originally
NOTE1—Theattainmentofanintimateanduniformblendoftwotypes
approved in 1996. Last previous edition approved in 2006 as D5370–06. DOI:
of fine material is difficult. Consequently, adequate equipment and
10.1520/D5370-06R13.
2 controls must be provided by the manufacturer. The purchaser should
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
ensure himself of the adequacy of the blending operation. See Appendix
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
X1 for the procedure.
Standards volume information, refer to the standard’s Document Summary page on
NOTE2—Certainrawmaterialslikeflyashandcementkilndust,which
the ASTM website.
3
Available from United States Environmental Protection Association (EPA), blends are covered by this specification, vary from source to source, as
Ariel Rios Bldg., 1200 Pennsylvania Ave., NW, Washington, DC 20460. well as within sources.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D5370−06 (2013)
4
7. Blended Pozzolan for Use with Lime 10.2.3 Determine non-carbonate carbon using test method
EPA 9060.
7.1 Ensure that blended pozzolan conforms to the require-
ments prescribed in Specification C593.
11. Storage and Inspection
5
8. Blended Pozzolan for Use in
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E1266-20(Practice)
Standard Practice for Processing Mixtures of Lime, Fly Ash, and Heavy Metal Wastes in Structural Fills and Other Construction Applications

SIGNIFICANCE AND USE
4.1 This practice provides users with current methods for preconditioning, handling, processing, and means of characterizing the materials that are produced.  
4.2 Lime and fly ash, and mixtures of lime and fly ash, can be useful for treating hazardous and nonhazardous waste as follows:  
4.2.1 Treating hazardous waste for potential resource recovery application;  
4.2.2 Solidifying liquids and sludges that are banned from land disposal because of excess free liquid content;  
4.2.3 Treating hazardous waste that may require treatment because of hazardous constituents prior to land disposal; and  
4.2.4 Treating hazardous waste for potential delisting to a nonhazardous waste status. Each one of these applications, however, must comply with requirements of the Resource Recovery and Conservation Act and the Hazardous and Solid Waste Amendments.
SCOPE
1.1 This practice provides descriptions and references of existing test methods and commercial practices relating to the processing of lime, fly ash, and heavy metal wastes in construction applications.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C117-23(Test Method)
Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing

SIGNIFICANCE AND USE
4.1 Material finer than the 75-μm (No. 200) sieve can be separated from larger particles much more efficiently and completely by wet sieving than through the use of dry sieving. Therefore, when accurate determinations of material finer than 75 μm (No. 200) in fine or coarse aggregate are desired, this test method is used on the sample prior to dry sieving in accordance with Test Method C136/C136M. The results of this test method are included in the calculation in Test Method C136/C136M, and the total amount of material finer than 75 μm (No. 200) by washing, plus that obtained by dry sieving the same sample, is reported with the results of Test Method C136/C136M. Usually, the additional amount of material finer than 75 μm (No. 200) obtained in the dry sieving process is a small amount. If it is large, the efficiency of the washing operation should be checked. It could also be an indication of degradation of the aggregate.  
4.2 Plain water is adequate to separate the material finer than 75 μm (No. 200) from the coarser material with most aggregates. In some cases, the finer material is adhering to the larger particles, such as some clay coatings and coatings on aggregates that have been extracted from bituminous mixtures. In these cases, the fine material will be separated more readily with a wetting agent in the water.
SCOPE
1.1 This test method covers the determination of the amount of material finer than a 75-μm (No. 200) sieve in aggregate by washing. Clay particles and other aggregate particles that are dispersed by the wash water, as well as water-soluble materials, will be removed from the aggregate during the test.  
1.2 Two procedures are included, one using only water for the washing operation, and the other including a wetting agent to assist the loosening of the material finer than the 75-μm (No. 200) sieve from the coarser material. Unless otherwise specified, Procedure A (water only) shall be used.  
1.3 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.
Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.  
1.4 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8021-23(Guide)
Standard Guide for Blast Furnace and Steel Furnace Slag as Produced During the Manufacture of Iron and Steel

SIGNIFICANCE AND USE
4.1 This guide provides guidance as to the appropriate/typical mineralogy observed when iron and steel slag is produced during a variety of processes in the manufacture of iron and steel.  
4.2 Slag can be considered a product based on the mineralogy of samples that are tested using X-ray diffraction, phase recognition and characterization, powdered XRD-Rietveld analysis, and SEM-PARC results, using this guide.
SCOPE
1.1 This standard is intended to provide guidance as to the appropriate/typical mineralogy observed when iron and steel slag, produced during the manufacture of iron and steel, is designated as a product. The included information covers the mineral properties of blast furnace slag and steel slag when they are manufactured in conjunction with the production of iron or steel, or both (Note 1).  
Note 1: This guide is not intended to be used to determine the applicability of iron or steel slag, or both, for various applications. Terminology D8 designates steel slag as a product, while Terminology C125 designates blast furnace slag as a product. Its sole intent is to provide guidance as to the typical mineralogy when the iron or steel slag, or both, is designated as a product.  
1.2 The values stated in SI units are to be regarded as standard. No other units are utilized in this standard.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) should not be considered as requirements of the specification.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM E3294-23(Guide)
Standard Guide for Forensic Analysis of Geological Materials by Powder X-Ray Diffraction

SIGNIFICANCE AND USE
5.1 The overarching goals of the forensic analysis of geological materials include (A) identification of an unknown material (see 11.3), (B) analysis of soils, sediments, or rocks to restrict their possible geographic origins as part of a provenance analysis (see 11.4), and (C) comparison of two or more samples to assess if they could have originated from the same source or to exclude a common source based on observation of exclusionary differences (see 11.5). XRD is only one analytical method that can be applied to the evidentiary samples in service of these distinct goals. Guidance for the analysis of forensic geological materials can be found in Refs (2-4).  
5.2 Within the analytical scheme of geological materials, XRD analysis is used to: identify the crystalline components within a sample; identify the crystalline components separated from a mixture, typically clay-sized material (see 8.8), or a selected particle class for which additional analysis is needed (see 8.11); or compare two or more samples based on the identified crystalline phases or diffraction patterns (see 11.5).  
5.2.1 Non-destructive XRD analysis can be performed in situ on geological material adhering to a substrate (see 8.12.3).  
5.2.2 The most common forensic applications of XRD to geological materials are (A) identification or confirmation of a selected phase or fraction of a sample (see 8.12), (B) identification of minerals in the clay-sized fractions of soils (see 8.8), and (C) identification of the phases of the hydrated cement component of concrete or mortar.  
5.3 This guide is intended to be used with other methods of analysis (for example, polarized light microscopy, scanning electron microscopy, palynology) within a more comprehensive analytical scheme for the forensic analysis or comparison of geological materials.  
5.3.1 Comprehensive criteria for forensic comparisons of geological material integrating multiple analytical methods and provenance estimations (see 11.4) are ...
SCOPE
1.1 This guide covers techniques and procedures for the use of powder X-ray diffraction (XRD) in the forensic analysis of geological materials (to include soils, rocks, sediments, and materials derived from them such as concrete), to enable non-consumptive identification of solid crystalline materials present as single components or multi-component mixtures.  
1.2 This guide makes recommendations for the preparation of geological materials for powder XRD analysis with adaptations for samples of limited quantity, instrumental configuration to generate high-quality XRD data, identification of crystalline materials by comparison to published diffraction data, and forensic comparison of XRD patterns from two or more samples of geological materials to support criminal investigations.  
1.3 Units—The values stated in SI units are to be regarded as standard. Other units are avoided, in general, but there is a long-standing tradition of expressing X-ray wavelengths and lattice spacing in units of Ångströms (Å). One Ångström = 10–10 meter (m) = 0.1 nanometer (nm).  
1.4 This standard is intended for use by competent forensic science practitioners with the requisite formal education, discipline-specific training (see Practice E2917), and demonstrated proficiency to perform forensic casework.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    15 pages
    English language
    sale 15% off
  • Guide
    15 pages
    English language
    sale 15% off
ASTM
ASTM C544-18(2023)(Test Method)
Standard Test Method for Hydration of Dead-Burned Magnesite or Periclase Grain

SIGNIFICANCE AND USE
3.1 This test method determines relative hydration resistance of magnesia grain.  
3.2 This test method is used in industry to evaluate grain samples and is used for specification purposes in some cases.  
3.3 Care must be taken in interpreting the data.
SCOPE
1.1 This test method covers the measurement of the relative resistance of magnesia grain to hydration.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C831-18(2023)(Test Method)
Standard Test Methods for Residual Carbon, Apparent Residual Carbon, and Apparent Carbon Yield in Coked Carbon-Containing Brick and Shapes

SIGNIFICANCE AND USE
3.1 These test methods are designed for use with carbon-containing products. The residual carbon content of a coked carbon-containing brick or shape is an indication of how much carbon may be available, in service, to resist slag attack on, or oxidation loss of, that body. Apparent carbon yield gives an estimate of the relative efficiency of the total carbonaceous matter to be retained as residual carbon.  
3.2 Residual carbon has a direct bearing on several properties of a pitch or resin-containing refractory, such as ignited porosity, density, strength, and thermal conductivity.  
3.3 These test methods are suitable for product development, manufacturing control, and specification acceptance.  
3.4 These test methods are very sensitive to specimen size, coking rates, etc.; therefore, strict compliance with these test methods is critical.  
3.5 Appreciable amounts of reducible components, such as Fe2O3, will have a noticeable effect on the results. Thus, values obtained by these test methods will be different when brick removed from service is tested. This must be kept in mind when attempting to use these test methods in an absolute sense.  
3.6 Oxidizable components such as metals and carbides can have a noticeable effect on the results. This must be kept in mind when using the second procedure, which is based on measuring weight loss after igniting the coked specimens.  
3.7 Testing of brick or shapes that contain magnesium metal presents special problems since this metal is highly volatile and substantial amounts of the magnesium can be lost from the sample during the coking procedure. This must be kept in mind when interpreting the results of testing of brick that contains magnesium. In addition, magnesium can react readily with atmospheric humidity. This must be kept in mind when storing brick that contains magnesium.
SCOPE
1.1 These test methods cover the determination of residual carbon content in carbon-bearing brick and shapes after a prescribed coking treatment. They provide two procedures. The first procedure is based on the combustion of carbon and its measurement as carbon dioxide. However, when using the first procedure for articles that contain silicon carbide or other carbides, no distinction will be made between carbon present in the form of a carbide and carbon present as elemental carbon. The second procedure provides a method for calculating apparent residual carbon (on the basis of weight loss after igniting the coked specimens), apparent carbonaceous material content, and apparent carbon yield. If the second procedure is used for brick or shapes that contain metallic additives or carbides, it must be recognized that there will be a weight gain associated with the oxidation of the metals, or carbides, or both. Such a weight gain can change the results substantially, and this must be kept in mind when interpreting the data.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C1526-19(2023)e1(Specification)
Standard Specification for Serpentine Dimension Stone

ABSTRACT
This specification covers the material characteristics, physical requirements, and sampling methods appropriate for the selection of serpentine (serpentine marble) dimension stone for general building and structural purposes. Dimension serpentine shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone. The physical property requirements to which serpentine stones shall adhere to are absorption by weight, density, compressive strength, modulus of rupture, abrasion resistance, and flexural strength.
SCOPE
1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate for the selection of serpentine (serpentine marble) for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of serpentine dimension stone.  
1.2 Dimension serpentine shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1073-18(2023)(Test Method)
Standard Test Method for Hydraulic Activity of Slag Cement by Reaction with Alkali

SIGNIFICANCE AND USE
4.1 This test method can be used as a quality-control test for slag production from a single source after adequate correlation with tests stipulated in Specification C989/C989M.  
4.2 This test method may be used as an evaluation technique for slag cement, when an appropriate correlation with various finenesses of slag cements from a specific source ground in a specific laboratory mill has been previously developed.  
4.3 The hydraulic activity as measured by this test method on slag cement samples can provide guidance to a manufacturer as to fineness level required to maintain a certain level of hydraulic activity.  
4.4 While this test method is intended primarily as a quality control test, some studies have shown that the test method is capable of evaluating the hydraulic activity of slag cements from different sources.
SCOPE
1.1 This test method covers the rapid determination of hydraulic activity of slag cement. This test method measures the accelerated strength development of the slag cement by using sodium hydroxide solution as mixing water and curing at elevated temperature.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in Section 6.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C4-04(2023)(Specification)
Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile

SCOPE
1.1 This specification establishes the criteria for acceptance, prior to installation, of drain tile and perforated drain tile to be used for underdrainage, filter fields, leaching fields, and similar subdrainage installations.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the Test Methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: Attention is called to Test Methods C301 and Terminology C896.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D7708-23a(Test Method)
Standard Test Method for Microscopical Determination of the Reflectance of Vitrinite Dispersed in Sedimentary Rocks

SIGNIFICANCE AND USE
5.1 The mean reflectance of the vitrinite maceral in sedimentary rocks as determined by this test method is used as an indicator of thermal maturity, that is, the progressive geochemical alteration of dispersed organic material experienced during diagenesis, catagenesis, and metagenesis. In the case of hydrocarbon source rocks, three major categories of thermal maturity are defined by vitrinite reflectance: immature (Roran ≤ 0.5 %), mature (Roran ≈ 0.5 % to 1.35 %), and overmature (Roran ≥ 1.35 %) with respect to the generation of liquid hydrocarbons, although not all practitioners agree on these thermal boundaries (10). Thermal maturity as determined by the reflectance of vitrinite dispersed in sedimentary rocks is similar to the rank classification of coals as presented in Classification D388 and measured similarly to the reflectance of vitrinite in coal as presented in Test Method D2798. The mean reflectance of the vitrinite maceral in sedimentary rocks correlates with geochemically determined parameters of thermal maturity and can be used to characterize thermal maturation history, to calibrate burial history models, and to better understand the processes of hydrocarbon generation, migration, and accumulation in conventional and unconventional petroleum systems.
SCOPE
1.1 This test method covers the microscopical determination of the reflectance measured in immersion oil of polished surfaces of vitrinite dispersed in sedimentary rocks. This test method can also be used to determine the reflectance of macerals other than vitrinite dispersed in sedimentary rocks.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off