ASTM D3171-11
(Test Method)Standard Test Methods for Constituent Content of Composite Materials
Standard Test Methods for Constituent Content of Composite Materials
SIGNIFICANCE AND USE
A constituent content of a composite material must be known in order to analytically model the material properties (mechanical, physical, thermal, or electrical) of the composite which are affected by the reinforcement or matrix. Also, knowledge of the constituent content is required for evaluation of the quality of a fabricated material and the processes used during fabrication.
The void volume of a composite material may significantly affect some of its mechanical properties. Higher void volumes usually mean lower fatigue resistance, greater susceptibility to moisture penetration and weathering, and increased variation or scatter in strength properties. Knowledge of the void volume of a composite material is desirable as an indication of the quality of a composite.
Reinforcement content may be used to normalize mechanical properties affected by amount of reinforcement in the coupon.
SCOPE
1.1 These test methods determine the constituent content of composite materials by one of two approaches. Test Method I physically removes the matrix by digestion or ignition by one of seven procedures, leaving the reinforcement essentially unaffected and thus allowing calculation of reinforcement or matrix content (by weight or volume) as well as percent void volume. Test Method II, applicable only to laminate materials of known fiber areal weight, calculates reinforcement or matrix content (by weight or volume), and the cured ply thickness, based on the measured thickness of the laminate. Test Method II is not applicable to the measurement of void volume.
1.1.1 These test methods are primarily intended for two-part composite material systems. However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can be determined in every case.
1.1.2 The procedures contained within have been designed to be particularly effective for certain classes of polymer or metal matrices. The suggested applications are discussed in Section 4, as well as at the start of each procedure.
1.1.3 Test Method I assumes that the reinforcement is essentially unaffected by the digestion or ignition medium. A procedure for correction of the results for minor changes in the reinforcement is included. Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace.
1.1.4 Test Method II assumes that the fiber areal weight of the reinforcement material form is known or controlled to an acceptable tolerance. The presence of voids is not measured. Eq 9 and 10 assume zero void content to perform the calculation.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 9 for additional information.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3171 − 11
StandardTest Methods for
1
Constituent Content of Composite Materials
This standard is issued under the fixed designation D3171; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 These test methods determine the constituent content of
responsibility of the user of this standard to establish appro-
composite materials by one of two approaches. Test Method I
priate safety and health practices and determine the applica-
physically removes the matrix by digestion or ignition by one
bility of regulatory limitations prior to use. See Section 9 for
of seven procedures, leaving the reinforcement essentially
additional information.
unaffected and thus allowing calculation of reinforcement or
matrix content (by weight or volume) as well as percent void
2. Referenced Documents
volume. Test Method II, applicable only to laminate materials
2
2.1 ASTM Standards:
ofknownfiberarealweight,calculatesreinforcementormatrix
D792 Test Methods for Density and Specific Gravity (Rela-
content (by weight or volume), and the cured ply thickness,
tive Density) of Plastics by Displacement
based on the measured thickness of the laminate. Test Method
D883 Terminology Relating to Plastics
II is not applicable to the measurement of void volume.
D1505 Test Method for Density of Plastics by the Density-
1.1.1 Thesetestmethodsareprimarilyintendedfortwo-part
Gradient Technique
composite material systems. However, special provisions can
D3878 Terminology for Composite Materials
be made to extend these test methods to filled material systems
D5229/D5229M TestMethodforMoistureAbsorptionProp-
with more than two constituents, though not all test results can
erties and Equilibrium Conditioning of Polymer Matrix
be determined in every case.
Composite Materials
1.1.2 The procedures contained within have been designed
E12 Terminology Relating to Density and Specific Gravity
to be particularly effective for certain classes of polymer or
3
of Solids, Liquids, and Gases (Withdrawn 1996)
metal matrices. The suggested applications are discussed in
E177 Practice for Use of the Terms Precision and Bias in
Section 4, as well as at the start of each procedure.
ASTM Test Methods
1.1.3 Test Method I assumes that the reinforcement is
E1309 Guide for Identification of Fiber-Reinforced
essentially unaffected by the digestion or ignition medium. A
Polymer-Matrix Composite Materials in Databases
procedure for correction of the results for minor changes in the
reinforcementisincluded.ProceduresAthroughFarebasedon
3. Terminology
chemicalremovalofthematrixwhileProcedureGremovesthe
matrix by igniting the matrix in a furnace. 3.1 Definitions—Terminology D3878 defines terms relating
1.1.4 Test Method II assumes that the fiber areal weight of to composite materials. Terminology D883 defines terms
the reinforcement material form is known or controlled to an relating to plastics. Terminology E12 defines terms relating to
acceptable tolerance. The presence of voids is not measured. specific gravity. Practice E177 defines terms relating to statis-
Eq 9 and 10 assume zero void content to perform the tics. In the event of a conflict between terms, Terminology
calculation. D3878 shall have precedence over other documents.
3.1.1 fiber content, n—the amount of fiber present in a
1.2 The values stated in SI units are to be regarded as
composite or prepreg expressed either as percent by weight or
standard. No other units of measurement are included in this
percent by volume.This is sometimes stated as a fraction. If no
standard.
fillers exist, this is equivalent to reinforcement content. D3878
1 2
These test methods are under the jurisdiction of ASTM Committee D30 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Composite Materials and are the direct responsibility of Subcommittee D30.04 on contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Lamina and Laminate Test Methods. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Oct. 1, 2011. Published November 2011. Originally the ASTM website.
3
approved in 1973. Last previous edition approved in 2009 as D3171 – 09. DOI: The last approved version of this historical standard is referenced on
10.1520/D3171-11. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1942
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3171–09 Designation:D3171–11
Standard Test Methods for
1
Constituent Content of Composite Materials
This standard is issued under the fixed designation D3171; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 These test methods determine the constituent content of composite materials by one of two approaches. Test Method I
physicallyremovesthematrixbydigestionorignitionbyoneofsevenprocedures,leavingthereinforcementessentiallyunaffected
and thus allowing calculation of reinforcement or matrix content (by weight or volume) as well as percent void volume. Test
MethodII,applicableonlytolaminatematerialsofknownfiberarealweight,calculatesreinforcementormatrixcontent(byweight
or volume), and the cured ply thickness, based on the measured thickness of the laminate. Test Method II is not applicable to the
measurement of void volume.
1.1.1 These test methods are primarily intended for two-part composite material systems. However, special provisions can be
made to extend these test methods to filled material systems with more than two constituents, though not all test results can be
determined in every case.
1.1.2 The procedures contained within have been designed to be particularly effective for certain classes of polymer or metal
matrices. The suggested applications are discussed in Section 4, as well as at the start of each procedure.
1.1.3 Test Method I assumes that the reinforcement is essentially unaffected by the digestion or ignition medium.Aprocedure
for correction of the results for minor changes in the reinforcement is included. Procedures A through F are based on chemical
removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace.
1.1.4 Test Method II assumes that the fiber areal weight of the reinforcement material form is known or controlled to an
acceptable tolerance. The presence of voids is not measured. Eq 9 and 10 assume zero void content to perform the calculation.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. See Section 9 for additional information.
2. Referenced Documents
2
2.1 ASTM Standards:
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D883 Terminology Relating to Plastics
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D3878 Terminology for Composite Materials
D5229/D5229M Test Method for MoistureAbsorption Properties and Equilibrium Conditioning of Polymer Matrix Composite
Materials
E12 Terminology Relating to Density and Specific Gravity of Solids, Liquids, and Gases
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E1309 Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases
3. Terminology
3.1 Definitions:
3.1.1Terminology Definitions—Terminology D3878 defines terms relating to composite materials. Terminology D883 defines
terms relating to plastics. Terminology E12 defines terms relating to specific gravity. Practice E177 defines terms relating to
statistics. In the event of a conflict between terms, Terminology D3878 shall have precedence over other documents.
1
These test methods are under the jurisdiction of ASTM Committee D30 on Composite Materials and are the direct responsibility of Subcommittee D30.04 on Lamina
and Laminate Test Methods.
Current edition approved AprilOct. 1, 2009.2011. Published May 2009.November 2011. Originally approved in 1973. Last previous edition approved in 20062009 as
D3171 – 069. DOI: 10.1520/D3171-09.10.1520/D3171-11.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 194
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.