iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1155-10(2015)

(Practice)

Standard Practice for Selection and Application of Piping System Materials

Standard Practice for Selection and Application of Piping System Materials

ABSTRACT
This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system material schedules for commercial ship design and construction. The materials and limitations listed in this specification meet the minimum requirements of the U.S. Coast Guard and the American Bureau of Shipping and should be considered to be the minimum acceptable materials in regard to material, design, and testing.
SCOPE
1.1 This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system material schedules for commercial ship design and construction.  
1.2 The materials and limitations listed in Tables 1-28 meet the minimum requirements of the U.S. Coast Guard and the American Bureau of Shipping and, except for titanium, should be considered to be the minimum acceptable materials in regard to material, design, and testing. This document is not intended to limit the selection of material strictly to those listed. Other equal or superior materials may be used provided that they are acceptable to the regulatory bodies and classification societies.  
Note 1: Titanium has been added as its use in fresh and sea water systems is becoming more common.

General Information

Status
Historical
Publication Date
30-Apr-2015
ICS
23.040.01 - Pipeline components and pipelines in general
47.020.30 - Piping systems
Technical Committee
F25 - Ships and Marine Technology
Drafting Committee
F25.11 - Machinery and Piping Systems
Current Stage
Ref Project

Relations

Replaces
ASTM F1155-10 - Standard Practice for Selection and Application of Piping System Materials
Effective Date
01-May-2015
Replaced By
ASTM F1155-10(2019) - Standard Practice for Selection and Application of Piping System Materials
Effective Date
01-Dec-2019
Referred By
ASTM F3386/F3386M-21 - Standard Specification for Detonation Flame Arresters
Effective Date
01-May-2015
Referred By
ASTM F2283-12(2018) - Standard Specification for Shipboard Oil Pollution Abatement System
Effective Date
01-May-2015
Referred By
ASTM F1386-92(2021) - Standard Guide for Construction of Sounding Tube and Striker Plate for Tank Sounding
Effective Date
01-May-2015
Referred By
ASTM F2363/F2363M-17(2023) - Standard Specification for Sewage and Graywater Flow Through Treatment Systems
Effective Date
01-May-2015
Referred By
ASTM F1311-90(2023) - Standard Specification for Large–Diameter Fabricated Carbon Steel Flanges
Effective Date
01-May-2015
Referred By
ASTM F1994-99(2023) - Standard Test Method for Shipboard Fixed Foam Firefighting Systems
Effective Date
01-May-2015
Referred By
ASTM F1273-21 - Standard Specification for Tank Vent Flame Arresters
Effective Date
01-May-2015

Buy Standard

ASTM F1155-10(2015) - Standard Practice for Selection and Application of Piping System MaterialsASTM F1155-10(2015) - Standard Practice for Selection and Application of Piping System Materials
PreviousNext
Standard
ASTM F1155-10(2015) - Standard Practice for Selection and Application of Piping System Materials
English language
21 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM F1155-10(2015) - Standard Practice for Selection and Application of Piping System MaterialsREDLINE ASTM F1155-10(2015) - Standard Practice for Selection and Application of Piping System Materials
PreviousNext
Standard
REDLINE ASTM F1155-10(2015) - Standard Practice for Selection and Application of Piping System Materials
English language
21 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1155 − 10 (Reapproved 2015) An American National Standard
Standard Practice for
1
Selection and Application of Piping System Materials
This standard is issued under the fixed designation F1155; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A181/A181M Specification for Carbon Steel Forgings, for
General-Purpose Piping
1.1 This practice is intended as a guide to shipbuilders,
A182/A182M Specification for Forged or Rolled Alloy and
shipowners, and design agents for use in the preparation of
Stainless Steel Pipe Flanges, Forged Fittings, and Valves
piping system material schedules for commercial ship design
and Parts for High-Temperature Service
and construction.
A192/A192M Specification for Seamless Carbon Steel
1.2 The materials and limitations listed in Tables 1-28 meet
Boiler Tubes for High-Pressure Service
the minimum requirements of the U.S. Coast Guard and the
A193/A193M Specification for Alloy-Steel and Stainless
American Bureau of Shipping and, except for titanium, should
Steel Bolting for High Temperature or High Pressure
be considered to be the minimum acceptable materials in
Service and Other Special Purpose Applications
regard to material, design, and testing. This document is not
A194/A194M Specification for Carbon Steel, Alloy Steel,
intended to limit the selection of material strictly to those
and Stainless Steel Nuts for Bolts for High Pressure or
listed. Other equal or superior materials may be used provided
High Temperature Service, or Both
that they are acceptable to the regulatory bodies and classifi-
A213/A213M Specification for Seamless Ferritic and Aus-
cation societies.
tenitic Alloy-Steel Boiler, Superheater, and Heat-
NOTE 1—Titanium has been added as its use in fresh and sea water
Exchanger Tubes
systems is becoming more common.
A214/A214M Specification for Electric-Resistance-Welded
2. Referenced Documents Carbon Steel Heat-Exchanger and Condenser Tubes
2
A216/A216M SpecificationforSteelCastings,Carbon,Suit-
2.1 ASTM Standards:
able for Fusion Welding, for High-Temperature Service
A53/A53M Specification for Pipe, Steel, Black and Hot-
A234/A234M Specification for Piping Fittings of Wrought
Dipped, Zinc-Coated, Welded and Seamless
Carbon Steel and Alloy Steel for Moderate and High
A105/A105M Specification for Carbon Steel Forgings for
Temperature Service
Piping Applications
A242/A242M Specification for High-Strength Low-Alloy
A106/A106M Specification for Seamless Carbon Steel Pipe
Structural Steel
for High-Temperature Service
A249/A249M Specification for Welded Austenitic Steel
A134 Specification for Pipe, Steel, Electric-Fusion (Arc)-
Welded (Sizes NPS 16 and Over) Boiler, Superheater, Heat-Exchanger, and Condenser
A139/A139M Specification for Electric-Fusion (Arc)- Tubes
Welded Steel Pipe (NPS 4 and Over) A283/A283M Specification for Low and Intermediate Ten-
A178/A178M Specification for Electric-Resistance-Welded sile Strength Carbon Steel Plates
Carbon Steel and Carbon-Manganese Steel Boiler and
A307 Specification for Carbon Steel Bolts, Studs, and
Superheater Tubes
Threaded Rod 60 000 PSI Tensile Strength
A179/A179M Specification for Seamless Cold-Drawn Low-
A320/A320M Specification for Alloy-Steel and Stainless
Carbon Steel Heat-Exchanger and Condenser Tubes
Steel Bolting for Low-Temperature Service
A335/A335M Specification for Seamless Ferritic Alloy-
1
Steel Pipe for High-Temperature Service
This practice is under the jurisdiction of ASTM Committee F25 on Ships and
Marine Technology and is the direct responsibility of Subcommittee F25.11 on
A351/A351M Specification for Castings, Austenitic, for
Machinery and Piping Systems.
Pressure-Containing Parts
Current edition approved May 1, 2015. Published June 2015. Originally
A387/A387M Specification for PressureVessel Plates,Alloy
approved in 1988. Last previous edition approved in 2010 as F1155 – 10. DOI:
10.1520/F1155-10R15.
Steel, Chromium-Molybdenum
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
A395/A395M Specification for Ferritic Ductile Iron
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Pressure-Retaining Castings for Use at ElevatedTempera-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. tures
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1155 − 10 (2015)
3
A515/A515M Specification for Pressure Vessel Plates, Car- 2.2 ANSI Standards:
bon Steel, for Intermediate- and Higher-Temperature
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1155 − 10 F1155 − 10 (Reapproved 2015) An American National Standard
Standard Practice for
1
Selection and Application of Piping System Materials
This standard is issued under the fixed designation F1155; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system
material schedules for commercial ship design and construction.
1.2 The materials and limitations listed in Tables 1-28 meet the minimum requirements of the U.S. Coast Guard and the
American Bureau of Shipping and, except for titanium, should be considered to be the minimum acceptable materials in regard
to material, design, and testing. This document is not intended to limit the selection of material strictly to those listed. Other equal
or superior materials may be used provided that they are acceptable to the regulatory bodies and classification societies.
NOTE 1—Titanium has been added as its use in fresh and sea water systems is becoming more common.
2. Referenced Documents
2
2.1 ASTM Standards:
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
A105/A105M Specification for Carbon Steel Forgings for Piping Applications
A106/A106M Specification for Seamless Carbon Steel Pipe for High-Temperature Service
A134 Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)
A139/A139M Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and Over)
A178/A178M Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater
Tubes
A179/A179M Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes
A181/A181M Specification for Carbon Steel Forgings, for General-Purpose Piping
A182/A182M Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts
for High-Temperature Service
A192/A192M Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service
A193/A193M Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other
Special Purpose Applications
A194/A194M Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High
Temperature Service, or Both
A213/A213M Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
A214/A214M Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes
A216/A216M Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service
A234/A234M Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature
Service
A242/A242M Specification for High-Strength Low-Alloy Structural Steel
A249/A249M Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes
A283/A283M Specification for Low and Intermediate Tensile Strength Carbon Steel Plates
A307 Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength
A320/A320M Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service
A335/A335M Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service
1
This practice is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.11 on Machinery
and Piping Systems.
Current edition approved Dec. 15, 2010May 1, 2015. Published February 2011June 2015. Originally approved in 1988. Last previous edition approved in 20042010 as
F1155 – 98F1155 – 10.(2004). DOI: 10.1520/F1155-98R04.10.1520/F1155-10R15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1155 − 10 (2015)
A351/A351M Specification for Castings, Austenitic, for Pres
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1155-10(2019)(Practice)
Standard Practice for Selection and Application of Piping System Materials

ABSTRACT
This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system material schedules for commercial ship design and construction. The materials and limitations listed in this specification meet the minimum requirements of the U.S. Coast Guard and the American Bureau of Shipping and should be considered to be the minimum acceptable materials in regard to material, design, and testing.
SCOPE
1.1 This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system material schedules for commercial ship design and construction.  
1.2 The materials and limitations listed in Tables 1-28 meet the minimum requirements of the U.S. Coast Guard and the American Bureau of Shipping and, except for titanium, should be considered to be the minimum acceptable materials in regard to material, design, and testing. This document is not intended to limit the selection of material strictly to those listed. Other equal or superior materials may be used provided that they are acceptable to the regulatory bodies and classification societies.  
Note 1: Titanium has been added as its use in fresh and sea water systems is becoming more common.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    24 pages
    English language
    sale 15% off
ASTM
ASTM F1155-10(2019)(Practice)
Standard Practice for Selection and Application of Piping System Materials

ABSTRACT
This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system material schedules for commercial ship design and construction. The materials and limitations listed in this specification meet the minimum requirements of the U.S. Coast Guard and the American Bureau of Shipping and should be considered to be the minimum acceptable materials in regard to material, design, and testing.
SCOPE
1.1 This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system material schedules for commercial ship design and construction.  
1.2 The materials and limitations listed in Tables 1-28 meet the minimum requirements of the U.S. Coast Guard and the American Bureau of Shipping and, except for titanium, should be considered to be the minimum acceptable materials in regard to material, design, and testing. This document is not intended to limit the selection of material strictly to those listed. Other equal or superior materials may be used provided that they are acceptable to the regulatory bodies and classification societies.  
Note 1: Titanium has been added as its use in fresh and sea water systems is becoming more common.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    24 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM B472-23(Specification)
Standard Specification for Nickel Alloy Billets and Bars for Reforging

ABSTRACT
This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556 nickel alloy billets and bars for reforging. The products shall be hot worked from ingots by rolling, forging, extruding, hammering, or pressing. The material shall conform to the chemical composition requirements prescribed by the reference material. The chemical composition of the material shall be determined by chemical analysis in accordance with test method E1473.
SCOPE
1.1 This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N10362, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, UNS N06699, and UNS R305562 billets and bars for reforging.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off