Standard Specification for Adhesives for Field-Gluing Wood Structural Panels (Plywood or Oriented Strand Board) to Wood Based Floor System Framing

ABSTRACT
This specification covers minimum performance standards and test requirements for gap-filling construction adhesives for field-gluing plywood to lumber framing for floor systems. The adhesive shall conform to the strength and durability properties prescribed. The different methods for specimen's preparation are presented in details. The shear strength, gap-filling effect on strength, and durability shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers minimum performance standards and test requirements for gap-filling construction adhesives for bonding wood structural panels consisting of plywood or oriented strand board (OSB) to wood based floor system framing, particularly dimension lumber or wood I-joists, at the construction site.  
1.2 This specification provides a basis for ensuring the quality of the adhesives and is not intended as an application specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-Jan-2018
Technical Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM D3498-18 - Standard Specification for Adhesives for Field-Gluing Wood Structural Panels (Plywood or Oriented Strand Board) to Wood Based Floor System Framing
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM D3498-18 - Standard Specification for Adhesives for Field-Gluing Wood Structural Panels (Plywood or Oriented Strand Board) to Wood Based Floor System Framing
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D3498 −18
Standard Specification for
Adhesives for Field-Gluing Wood Structural Panels
(Plywood or Oriented Strand Board) to Wood Based Floor
1
System Framing
This standard is issued under the fixed designation D3498; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D572Test Method for Rubber—Deterioration by Heat and
Oxygen
1.1 This specification covers minimum performance stan-
D905Test Method for Strength Properties of Adhesive
dards and test requirements for gap-filling construction adhe-
Bonds in Shear by Compression Loading
sivesforbondingwoodstructuralpanelsconsistingofplywood
D907Terminology of Adhesives
or oriented strand board (OSB) to wood based floor system
D4300Test Methods for Ability of Adhesive Films to
framing, particularly dimension lumber or wood I-joists, at the
Support or Resist the Growth of Fungi
construction site.
D4442Test Methods for Direct Moisture Content Measure-
1.2 This specification provides a basis for ensuring the
ment of Wood and Wood-Based Materials
quality of the adhesives and is not intended as an application
D4444Test Method for Laboratory Standardization and
specification.
Calibration of Hand-Held Moisture Meters
D4783Test Methods for Resistance of Adhesive Prepara-
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical tions in Container toAttack by Bacteria,Yeast, and Fungi
E4Practices for Force Verification of Testing Machines
conversions to SI units that are provided for information only
and are not considered standard. E177Practice for Use of the Terms Precision and Bias in
ASTM Test Methods
1.4 The following precautionary caveat pertains only to the
3
2.2 Voluntary Product Standards:
test method portion, Section 11, of this specification: This
PS1Structural Plywood
standard does not purport to address all of the safety concerns,
PS2Performance Standard for Wood-Based Structural-Use
if any, associated with its use. It is the responsibility of the user
Panels
of this standard to establish appropriate safety, health, and
environmental practices and determine the applicability of
3. Terminology
regulatory limitations prior to use.
3.1 Definitions:
1.5 This international standard was developed in accor-
3.1.1 Many terms in this specification are defined in Termi-
dance with internationally recognized principles on standard-
nology D907.
ization established in the Decision on Principles for the
3.1.2 gap-filling adhesive, n—an adhesive capable of form-
Development of International Standards, Guides and Recom-
ing and maintaining a bond between surfaces that are not
mendations issued by the World Trade Organization Technical
close-fitting.
Barriers to Trade (TBT) Committee.
3.1.2.1 Discussion—Close-fitting is relative to a given ma-
terial and industry; for example, standards in construction
2. Referenced Documents
differ from standards in electronics. Some adhesives will bond
2
2.1 ASTM Standards:
bybridgingwithoutcompletelyfillingthegap;othersbyfilling
the gap completely.
1 3.1.3 open assembly time, n—the time interval between
This specification is under the jurisdiction of ASTM Committee D14 on
Adhesives and is the direct responsibility of Subcommittee D14.70 on Construction applying adhesive on the substrates and closing them together
Adhesives.
before bonding.
Current edition approved Feb. 1, 2018. Published March 2018. Originally
3.1.4 oriented strand board (OSB), n—a mat formed panel
approved in 1976. Last previous edition approved in 2011 as D3498–03 (2011).
DOI: 10.1520/D3498-18.
product with oriented layers resulting in directional properties.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from National Institute of Standards and Technology (NIST), 100
the ASTM website. Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3498−18
3.1.5 plywood, n—a conventional all-veneer panel with 6.2 Theadhesiveshallnotsupportmoldorbacterialgrowth.
alternatelayersofveneerwhichareorientatedperpendicularto If amylaceous or protein fillers and extenders are used in the
each other. adhesive formulation, the adhesive must not only pass the
performancerequirementsofthisspecification,butinaddition,
3.1.6 wood-I joist, n—a s
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3498 − 03 (Reapproved 2011) D3498 − 18
Standard Specification for
Adhesives for Field-Gluing Plywood to Lumber Framing for
Floor SystemsWood Structural Panels (Plywood or Oriented
1
Strand Board) to Wood Based Floor System Framing
This standard is issued under the fixed designation D3498; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers minimum performance standards and test requirements for gap-filling construction adhesives for
bonding plywood to lumber framing, particularly floor joists, wood structural panels consisting of plywood or oriented strand board
(OSB) to wood based floor system framing, particularly dimension lumber or wood I-joists, at the construction site.
1.2 This specification provides a basis for ensuring the quality of the adhesives and is not intended as an application
specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification:This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D572 Test Method for Rubber—Deterioration by Heat and Oxygen
D905 Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading
D907 Terminology of Adhesives
3
D2016 Methods of Test for Moisture Content of Wood (Withdrawn 1987)
D4300 Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi
D4442 Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
D4444 Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
D4783 Test Methods for Resistance of Adhesive Preparations in Container to Attack by Bacteria, Yeast, and Fungi
E4 Practices for Force Verification of Testing Machines
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
3
2.2 Voluntary Product Standards:
PS1 Structural Plywood
PS2 Performance Standard for Wood-Based Structural-Use Panels
3. Terminology
3.1 Definitions:
3.1.1 Many terms in this specification are defined in Terminology D907.
1
This specification is under the jurisdiction of ASTM Committee D14 on Adhesives and is the direct responsibility of Subcommittee D14.70 on Construction Adhesives.
Current edition approved Jan. 1, 2011Feb. 1, 2018. Published January 2011March 2018. Originally approved in 1976. Last previous edition approved in 20032011 as
D3498 – 03.D3498 – 03 (2011). DOI: 10.1520/D3498-03R11.10.1520/D3498-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.Available from National Institute of Standards and Technology (NIST), 100 Bureau
Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3498 − 18
3.1.2 gap-filling adhesive, n—an adhesive capable of forming and maintaining a bond between surfaces that are not close-fitting.
3.1.2.1 Discussion—
Close-fitting is relative to a given material and industry; for example, standards in construction differ from standards in electronics.
Some adhesives will bond by bridging without completely filling the gap; others by
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.