iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1592-01

(Test Method)

Standard Test Methods for Detention Hollow Metal Vision Systems

Standard Test Methods for Detention Hollow Metal Vision Systems

SCOPE
1.1 These test methods cover fixed detention hollow metal vision systems of various materials and types of construction. These fixed hollow metal vision systems are used in wall openings in detention and correctional institutions designed to incarcerate inmates.
1.2 Frame assemblies investigated under these test methods include individual components including detention security hollow metal frames, frame anchoring, security glazing, panels, and removable glazing stops.
1.3 These test methods are designed to test the capability of a fixed detention hollow metal vision system to prevent, delay, and frustrate escape; to limit or control access to unauthorized or secured areas; and prevent passage of contraband.
1.4 These test methods apply primarily to detention hollow metal vision systems between secure areas generally found inside a detention/correctional facility such as: day rooms, control rooms, cells, and sally ports. These test methods are applicable to vision systems other than hollow metal, provided testing and reporting procedures are followed.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Dec-2001
ICS
91.040.10 - Public buildings
Technical Committee
F33 - Detention and Correctional Facilities
Drafting Committee
F33.02 - Physical Barriers
Current Stage
Ref Project

Relations

Replaces
ASTM F1592-95a - Standard Test Methods for Detention Hollow Metal Vision Systems
Effective Date
10-Dec-2001
Replaced By
ASTM F1592-05 - Standard Test Methods for Detention Hollow Metal Vision Systems
Effective Date
01-Feb-2005
Referred By
ASTM F1643-05(2019) - Standard Test Methods for Detention Sliding Door Locking Device Assembly
Effective Date
10-Dec-2001
Referred By
ASTM F1758-05(2019) - Standard Test Methods for Detention Hinges Used on Detention-Grade Swinging Doors
Effective Date
10-Dec-2001
Referred By
ASTM F2956-22 - Standard Test Methods for Anchor Systems Used for Detention Hollow Metal Systems
Effective Date
10-Dec-2001
Referred By
ASTM F2322-12(2019) - Standard Test Methods for Physical Assault on Vertical Fixed Barriers for Detention and Correctional Facilities
Effective Date
10-Dec-2001
Referred By
ASTM F1577-05(2019) - Standard Test Methods for Detention Locks for Swinging Doors
Effective Date
10-Dec-2001
Referred By
ASTM F1450-12a(2019) - Standard Test Methods for Hollow Metal Swinging Door Assemblies for Detention and Correctional Facilities
Effective Date
10-Dec-2001
Referred By
ASTM F1915-05(2019) - Standard Test Methods for Glazing for Detention Facilities
Effective Date
10-Dec-2001
Referred By
ASTM F2697-15 - Standard Test Methods for Physical Assault on Overhead Horizontal Fixed Barriers for Detention and Correctional Facilities
Effective Date
10-Dec-2001

Buy Standard

ASTM F1592-01 - Standard Test Methods for Detention Hollow Metal Vision SystemsASTM F1592-01 - Standard Test Methods for Detention Hollow Metal Vision Systems
PreviousNext
Standard
ASTM F1592-01 - Standard Test Methods for Detention Hollow Metal Vision Systems
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1592–01
Standard Test Methods for
1
Detention Hollow Metal Vision Systems
This standard is issued under the fixed designation F 1592; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope Security Hollow Metal Doors and Frames
4
2.3 NFPA Standard:
1.1 These test methods cover fixed detention hollow metal
252 Methods of Fire Tests of Door Assemblies
vision systems of various materials and types of construction.
5
2.4 UL Standards:
These fixed hollow metal vision systems are used in wall
UL-10 (C) Fire Tests of Door Assemblies
openings in detention and correctional institutions designed to
UL-752 Bullet Resisting Equipment
incarcerate inmates.
1.2 Frame assemblies investigated under these test methods
3. Terminology
include individual components including detention security
3.1 Definitions of Terms Specific to This Standard:
hollow metal frames, frame anchoring, security glazing, pan-
3.1.1 borrowed light, n—a fixed window frame for use in an
els, and removable glazing stops.
interior partition.
1.3 These test methods are designed to test the capability of
3.1.1.1 Discussion—This term is derived from the concept
a fixed detention hollow metal vision system to prevent, delay,
of borrowing light from one room or space to help illuminate
and frustrate escape; to limit or control access to unauthorized
another.
or secured areas; and prevent passage of contraband.
3.1.2 butt joint, n—the corner or mullion joint of a frame in
1.4 These test methods apply primarily to detention hollow
which the stop of either member is notched to fit the other,
metal vision systems between secure areas generally found
resulting in a perpendicular joint.
inside a detention/correctional facility such as: day rooms,
3.1.3 component, n—asubassembly,asdistinguishedfroma
control rooms, cells, and sally ports. These test methods are
part, that combines with other components to make up a total
applicable to vision systems other than hollow metal, provided
frame assembly.
testing and reporting procedures are followed.
3.1.3.1 Discussion—The prime components of a fixed vi-
1.5 The values stated in inch-pound units are to be regarded
sion system assembly are frame, wall, glazing, and panels.
as the standard. The values given in parentheses are for
3.1.4 contraband breach, n—any through opening created
information only.
such that a 0.060-in.–diameter wire can be passed completely
1.6 This standard does not purport to address all of the
through the assembly at any location constitutes a contraband
safety concerns, if any, associated with its use. It is the
breach.
responsibility of the user of this standard to establish appro-
3.1.5 detention security, n—ensurance of the restriction of
priate safety and health practices and determine the applica-
mobility of inmates to designated areas within a correctional or
bility of regulatory limitations prior to use.
detention facility.
2. Referenced Documents 3.1.6 forcible egress, n—the ability to pass a 5 3 8 3 8–in.
rigid rectangular box through an opening in the test sample
2.1 ASTM Standards:
created by destructive testing procedures.
E 2074 Test Method for Fire Tests of Door Assemblies,
3.1.7 glazing stop, n—aformedmetalsectionusedtosecure
Including Positive Pressure Testing of Side-Hinged and
2 glazing or panel in a frame either by application to the glazing
Pivoted Swinging Door Assemblies
3
material or as an integral part of the frame.
2.2 NAAMM/HMMA Standard:
3.1.8 head or header, n—the horizontal member that forms
ANSI/HMMA 863-98 Guide Specifications for Detention
the top of a frame.
3.1.9 hollow metal, n—a term used in reference to such
items as doors, frames, partitions, enclosures, and other items
1
These test methods are under the jurisdiction of ASTM Committee F33 on
that are fabricated from metal sheet, usually carbon steel.
Detention and Correctional Facilities and are the direct responsibility of Subcom-
mittee F33.02 on Physical Barriers.
Current edition approved Dec. 10, 2001. Published January 2002. Originally
4
published as F 1592 – 95. Last previous edition F 1592 – 95. Available from National Fire Protection Association, Batterymarch Park,
2
Annual Book of ASTM Standards, Vol 04.07. Quincy, MA 02269.
3 5
Available from Hollow Metal Manufacturer’s Association, A Division of Available from Underwriters Laboratories, 333 Pfingsten Road, Northbrook, IL
NAAMM, 600 S. Federal St., Chicago, IL 60605. 60062.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 --------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2322-12(2019)(Test Method)
Standard Test Methods for Physical Assault on Vertical Fixed Barriers for Detention and Correctional Facilities

SIGNIFICANCE AND USE
4.1 A major concern for administrative officials is the security of barriers used in detention/correctional facilities. These test methods are designed to aid in identifying levels of physical security for walls which enclose or separate secure areas. This does not apply to the passage of contraband.  
4.2 These test methods are not intended to provide a measure of resistance for a wall subjected to attack by corrosive agents, by high-powered rifles, explosives, sawing, or other such methods. These test methods are intended to evaluate the resistance of a wall to violent attacks by sustained manpower using battering devices, such as benches, bunks, or tables, and by handguns up to and including .44 magnum. Attacks from the outside and fire resistance ratings are not addressed in this standard.  
4.3 The primary purpose or result of these test methods is to approximate the levels of abuse to which walls will potentially be subjected in the field. The desired result of its use is to help provide assurance of protection to the public, to facility administrative personnel, and to the inmates themselves.  
4.4 It is recommended that detention/correctional facility administration provide adequate training, supervision, and preventative maintenance programs to enable walls to function as intended throughout the expected service life.
SCOPE
1.1 These test methods cover requirements for simulated service tests and testing equipment for determining the performance characteristics of walls designed to incarcerate inmates in detention and correctional institutions. The testing equipment provides for the setup and testing of two sample fixed barriers side-by-side, one with no openings and one equipped with a representative penetration in accordance with the American Correctional Association (ACA) standard for clear view area of 3 ft2  (0.279 m2), 12 in. (305 mm) wide by 36 in. (914 mm) high.  
1.2 It is the intent of these test methods to help ensure that detention security walls perform at or above minimum acceptable levels to control passage of unauthorized or secure areas, to confine inmates, to delay and frustrate escape attempts, and to resist vandalism. It is recognized that in order to meet the intent of these test methods, opening assemblies within these walls must be compatible with the level of performance required by: Test Methods F1450, F1592, and F1643.  
1.3 These test methods apply to walls enclosing or separating secure areas of detention/correctional facilities.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are approximate and for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F2542-05(2019)(Test Method)
Standard Test Methods for Physical Assault on Ventilation Grilles for Detention and Correctional Facilities

SIGNIFICANCE AND USE
4.1 A major concern for administration officials is security of barriers used in detention/correctional facilities. These test methods are designed to identify the security levels for ventilation grilles mounted within these barriers.  
4.2 The purpose of these tests is to approximate levels of abuse to which grilles will potentially be subjected in the field, and to provide assurance of protection to the public, facility administrative personnel, and inmates.
SCOPE
1.1 These test methods cover requirements for simulated service tests and testing equipment for determining the performance characteristics of ventilation grilles used in secure areas, including detention and correctional facilities. The testing equipment provides for the setup and testing of specimen grilles and mounting systems. It is recognized that, in order to meet the intent of these test methods, ventilation grilles must be compatible with the level of performance require by Test Methods F2322.  
1.2 It is the intent of these test methods to ensure that security ventilation grilles meet minimum performance levels to control the passage of unauthorized materials into secure areas, to confine inmates, to resist vandalism, and to delay or frustrate escape, or both. It is also the responsibility of the user of these test methods to insure that the grille selected is appropriate, based on relevant regulatory, health, and safety concerns and requirements. Such concerns include, but are not limited to, injury and suicide avoidance. These test methods do not quantify such concerns.  
1.3 Take care to provide access to return and exhaust ducts for cleaning as required by NFPA 90A. If access cannot be provided though an interstitial space behind walls or ceiling, the use of filter grilles needs to be considered as an option. When filter grilles are provided, filters shall have a minimum UL-900 class 2 rating, and a filter replacement program needs to be in place at the facility.  
1.4 Airflow performance shall be catalogued in accordance with ASHRAE 70–91. Manufacturer’s catalog data must include grade level achieved.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1592-12(2019)(Test Method)
Standard Test Methods for Detention Hollow Metal Vision Systems

SIGNIFICANCE AND USE
4.1 A major concern for corrections administration officials is the resistance of security barriers used in detention/correctional facilities to certain types of physical attack that it is reasonable to expect in the field. These test methods are designed to aid in identifying a level of physical security for fixed detention hollow metal vision systems.  
4.2 These test methods are not intended to provide a measure of resistance for a vision system subjected to attack by corrosive agents, high-powered rifles, explosives, sawing, or other such methods. These test methods are intended to evaluate the resistance of a vision system to violent attacks using battering devices such as benches, bunks, fire extinguishers, or tables; hand guns up to and including the .44 magnum; and fires started by using mattresses, books, and similar flammable materials.  
4.3 The primary purpose or result of this standard is to provide detailed test methods that approximate the levels of abuse to which it is possible that vision systems become subjected in the field. The desired result of its use is to give assurance of protection to the public, to prison administrative personnel, and to the inmates themselves in the event of such attack.  
4.4 It is recommended that detention/correctional facility administration provide adequate training, supervision and preventative maintenance programs to enable door assemblies to function as intended throughout the expected service life.
SCOPE
1.1 These test methods cover fixed detention hollow metal vision systems of various materials and types of construction. These fixed hollow metal vision systems are used in wall openings in detention and correctional institutions designed to incarcerate inmates.  
1.2 Frame assemblies investigated under these test methods include individual components including detention security hollow metal frames, frame anchoring, security glazing, panels, and removable glazing stops.  
1.3 These test methods are designed to test the capability of a fixed detention hollow metal vision system to prevent, delay, and frustrate escape; to limit or control access to unauthorized or secured areas; and prevent passage of contraband.  
1.4 These test methods apply primarily to detention hollow metal vision systems between secure areas generally found inside a detention/correctional facility such as: day rooms, control rooms, cells, and sally ports. These test methods are applicable to vision systems other than hollow metal, provided testing and reporting procedures are followed.  
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM F2697-15(Test Method)
Standard Test Methods for Physical Assault on Overhead Horizontal Fixed Barriers for Detention and Correctional Facilities

SIGNIFICANCE AND USE
4.1 A major concern for administrative officials is the security of barriers used in detention/correctional facilities. These test methods are designed to aid in identifying levels of physical security for horizontal fixed barriers, which serve to enclose or separate secure areas. This does not apply to the passage of contraband or vandalism.  
4.2 These test methods are not intended to provide a measure of resistance for a ceiling subjected to attack by corrosive agents, by high-powered rifles, explosives, sawing, or other such methods not typically available to inmates. These test methods are intended to evaluate the resistance of a ceiling to violent attacks by sustained manpower using battering devices, such as benches, barbells, bunks, or tables; and by an upward static force such that could be applied by an inmate pushing against the ceiling with his hands, feet, or back (that is, squat position on a top bunk in a cell). Attacks from outside the facility and fire resistance ratings are not addressed in this standard.  
4.3 The primary purpose or result of these test methods is to approximate the levels of abuse to which horizontal fixed barriers could possibly be subjected in the field. The desired result of its use is to help provide assurance of protection to the public, to facility personnel, and to the inmates themselves.  
4.4 It is recommended that detention/correctional facility administration provide adequate training, supervision, and preventive maintenance programs to enable horizontal fixed barriers to function as intended throughout the expected service life.
SCOPE
1.1 These test methods cover requirements for simulated service tests and testing equipment for determining the performance characteristics of horizontal fixed barriers designed to incarcerate inmates in detention and correctional institutions. The testing equipment provides for the setup and testing of sample barriers and installation systems.  
1.2 It is the intent of these test methods to help ensure that detention security horizontal fixed barriers perform at or above minimum acceptable levels for control of passage to unauthorized or secure areas, to confine inmates, and to delay and frustrate escape attempts. Provide security grilles, access doors, light fixtures, and similar assemblies compatible with these levels of performance, with test apparatus adjustments as required to suit the particular product.  
1.3 These test methods apply to horizontal fixed barriers enclosing or separating secure areas of detention/correctional facilities.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversion to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM F2322-12(2019)(Test Method)
Standard Test Methods for Physical Assault on Vertical Fixed Barriers for Detention and Correctional Facilities

SIGNIFICANCE AND USE
4.1 A major concern for administrative officials is the security of barriers used in detention/correctional facilities. These test methods are designed to aid in identifying levels of physical security for walls which enclose or separate secure areas. This does not apply to the passage of contraband.  
4.2 These test methods are not intended to provide a measure of resistance for a wall subjected to attack by corrosive agents, by high-powered rifles, explosives, sawing, or other such methods. These test methods are intended to evaluate the resistance of a wall to violent attacks by sustained manpower using battering devices, such as benches, bunks, or tables, and by handguns up to and including .44 magnum. Attacks from the outside and fire resistance ratings are not addressed in this standard.  
4.3 The primary purpose or result of these test methods is to approximate the levels of abuse to which walls will potentially be subjected in the field. The desired result of its use is to help provide assurance of protection to the public, to facility administrative personnel, and to the inmates themselves.  
4.4 It is recommended that detention/correctional facility administration provide adequate training, supervision, and preventative maintenance programs to enable walls to function as intended throughout the expected service life.
SCOPE
1.1 These test methods cover requirements for simulated service tests and testing equipment for determining the performance characteristics of walls designed to incarcerate inmates in detention and correctional institutions. The testing equipment provides for the setup and testing of two sample fixed barriers side-by-side, one with no openings and one equipped with a representative penetration in accordance with the American Correctional Association (ACA) standard for clear view area of 3 ft2  (0.279 m2), 12 in. (305 mm) wide by 36 in. (914 mm) high.  
1.2 It is the intent of these test methods to help ensure that detention security walls perform at or above minimum acceptable levels to control passage of unauthorized or secure areas, to confine inmates, to delay and frustrate escape attempts, and to resist vandalism. It is recognized that in order to meet the intent of these test methods, opening assemblies within these walls must be compatible with the level of performance required by: Test Methods F1450, F1592, and F1643.  
1.3 These test methods apply to walls enclosing or separating secure areas of detention/correctional facilities.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are approximate and for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F2542-05(2019)(Test Method)
Standard Test Methods for Physical Assault on Ventilation Grilles for Detention and Correctional Facilities

SIGNIFICANCE AND USE
4.1 A major concern for administration officials is security of barriers used in detention/correctional facilities. These test methods are designed to identify the security levels for ventilation grilles mounted within these barriers.  
4.2 The purpose of these tests is to approximate levels of abuse to which grilles will potentially be subjected in the field, and to provide assurance of protection to the public, facility administrative personnel, and inmates.
SCOPE
1.1 These test methods cover requirements for simulated service tests and testing equipment for determining the performance characteristics of ventilation grilles used in secure areas, including detention and correctional facilities. The testing equipment provides for the setup and testing of specimen grilles and mounting systems. It is recognized that, in order to meet the intent of these test methods, ventilation grilles must be compatible with the level of performance require by Test Methods F2322.  
1.2 It is the intent of these test methods to ensure that security ventilation grilles meet minimum performance levels to control the passage of unauthorized materials into secure areas, to confine inmates, to resist vandalism, and to delay or frustrate escape, or both. It is also the responsibility of the user of these test methods to insure that the grille selected is appropriate, based on relevant regulatory, health, and safety concerns and requirements. Such concerns include, but are not limited to, injury and suicide avoidance. These test methods do not quantify such concerns.  
1.3 Take care to provide access to return and exhaust ducts for cleaning as required by NFPA 90A. If access cannot be provided though an interstitial space behind walls or ceiling, the use of filter grilles needs to be considered as an option. When filter grilles are provided, filters shall have a minimum UL-900 class 2 rating, and a filter replacement program needs to be in place at the facility.  
1.4 Airflow performance shall be catalogued in accordance with ASHRAE 70–91. Manufacturer’s catalog data must include grade level achieved.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1592-12(2019)(Test Method)
Standard Test Methods for Detention Hollow Metal Vision Systems

SIGNIFICANCE AND USE
4.1 A major concern for corrections administration officials is the resistance of security barriers used in detention/correctional facilities to certain types of physical attack that it is reasonable to expect in the field. These test methods are designed to aid in identifying a level of physical security for fixed detention hollow metal vision systems.  
4.2 These test methods are not intended to provide a measure of resistance for a vision system subjected to attack by corrosive agents, high-powered rifles, explosives, sawing, or other such methods. These test methods are intended to evaluate the resistance of a vision system to violent attacks using battering devices such as benches, bunks, fire extinguishers, or tables; hand guns up to and including the .44 magnum; and fires started by using mattresses, books, and similar flammable materials.  
4.3 The primary purpose or result of this standard is to provide detailed test methods that approximate the levels of abuse to which it is possible that vision systems become subjected in the field. The desired result of its use is to give assurance of protection to the public, to prison administrative personnel, and to the inmates themselves in the event of such attack.  
4.4 It is recommended that detention/correctional facility administration provide adequate training, supervision and preventative maintenance programs to enable door assemblies to function as intended throughout the expected service life.
SCOPE
1.1 These test methods cover fixed detention hollow metal vision systems of various materials and types of construction. These fixed hollow metal vision systems are used in wall openings in detention and correctional institutions designed to incarcerate inmates.  
1.2 Frame assemblies investigated under these test methods include individual components including detention security hollow metal frames, frame anchoring, security glazing, panels, and removable glazing stops.  
1.3 These test methods are designed to test the capability of a fixed detention hollow metal vision system to prevent, delay, and frustrate escape; to limit or control access to unauthorized or secured areas; and prevent passage of contraband.  
1.4 These test methods apply primarily to detention hollow metal vision systems between secure areas generally found inside a detention/correctional facility such as: day rooms, control rooms, cells, and sally ports. These test methods are applicable to vision systems other than hollow metal, provided testing and reporting procedures are followed.  
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM F2697-15(Test Method)
Standard Test Methods for Physical Assault on Overhead Horizontal Fixed Barriers for Detention and Correctional Facilities

SIGNIFICANCE AND USE
4.1 A major concern for administrative officials is the security of barriers used in detention/correctional facilities. These test methods are designed to aid in identifying levels of physical security for horizontal fixed barriers, which serve to enclose or separate secure areas. This does not apply to the passage of contraband or vandalism.  
4.2 These test methods are not intended to provide a measure of resistance for a ceiling subjected to attack by corrosive agents, by high-powered rifles, explosives, sawing, or other such methods not typically available to inmates. These test methods are intended to evaluate the resistance of a ceiling to violent attacks by sustained manpower using battering devices, such as benches, barbells, bunks, or tables; and by an upward static force such that could be applied by an inmate pushing against the ceiling with his hands, feet, or back (that is, squat position on a top bunk in a cell). Attacks from outside the facility and fire resistance ratings are not addressed in this standard.  
4.3 The primary purpose or result of these test methods is to approximate the levels of abuse to which horizontal fixed barriers could possibly be subjected in the field. The desired result of its use is to help provide assurance of protection to the public, to facility personnel, and to the inmates themselves.  
4.4 It is recommended that detention/correctional facility administration provide adequate training, supervision, and preventive maintenance programs to enable horizontal fixed barriers to function as intended throughout the expected service life.
SCOPE
1.1 These test methods cover requirements for simulated service tests and testing equipment for determining the performance characteristics of horizontal fixed barriers designed to incarcerate inmates in detention and correctional institutions. The testing equipment provides for the setup and testing of sample barriers and installation systems.  
1.2 It is the intent of these test methods to help ensure that detention security horizontal fixed barriers perform at or above minimum acceptable levels for control of passage to unauthorized or secure areas, to confine inmates, and to delay and frustrate escape attempts. Provide security grilles, access doors, light fixtures, and similar assemblies compatible with these levels of performance, with test apparatus adjustments as required to suit the particular product.  
1.3 These test methods apply to horizontal fixed barriers enclosing or separating secure areas of detention/correctional facilities.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversion to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off