ASTM D5740-09

Standard Guide for Writing Material Standards in the Classification D4000 Format

ABSTRACT
This guide has been prepared to aid in the writing of material standards using the Classification D 4000 format.
SCOPE
1.1 This classification system covers ___ materials suitable for _____________. The inclusion or exclusion of recycled plastics in this classification system must be addressed here.
1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using the suffixes as given in Section 5.
1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this standard.
Note 1—Insert Note 1 here to show the appropriate ISO equivalency statement.  
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Aug-2009
• ICS: 01.120 - Standardization. General rules
• ICS: 35.260 - Office machines
• ICS: 85.080 - Paper products
• Technical Committee: D20 - Plastics

Relations

• Replaces: ASTM D5740-03 - Standard Guide for Writing Material Standards in the Classification D4000 Format
• Effective Date: 01-Sep-2009
• Replaced By: ASTM D5740-11 - Standard Guide for Writing Material Standards in the Classification D4000 Format
• Effective Date: 01-Sep-2011
• Referred By: ASTM D707-15(2023) - Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB)
• Effective Date: 01-Sep-2009
• Referred By: ASTM D4968-19a - Standard Practice for Annual Review of Test Methods and Specifications for Plastics
• Effective Date: 01-Sep-2009
• Referred By: ASTM D1562-22 - Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP)
• Effective Date: 01-Sep-2009
• Referred By: ASTM D1710-15(2021) - Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes
• Effective Date: 01-Sep-2009
• Referred By: ASTM D5205-16 - Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
• Effective Date: 01-Sep-2009
• Referred By: ASTM D5675-13(2018) - Standard Classification for Low Molecular Weight PTFE and FEP Micronized Powders
• Effective Date: 01-Sep-2009
• Referred By: ASTM D4067-23 - Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
• Effective Date: 01-Sep-2009
• Referred By: ASTM D5575-18(2023) - Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers
• Effective Date: 01-Sep-2009
• Referred By: ASTM D3368-17(2022) - Standard Specification for FEP Sheet and Film
• Effective Date: 01-Sep-2009
• Referred By: ASTM D706-20 - Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)
• Effective Date: 01-Sep-2009
• Referred By: ASTM D6779-23 - Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
• Effective Date: 01-Sep-2009
• Referred By: ASTM D6394-21a - Standard Classification System for and Basis for Specification for Sulfone Plastics (SP)
• Effective Date: 01-Sep-2009

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5740 – 09
Standard Guide for
Writing Material Standards in the Classification D4000
1
Format
This standard is issued under the fixed designation D5740; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This guide has been prepared to aid in the writing of material standards using the Classification
D4000 format. The following template is included which might be used directly for a draft document
simply by filling in the blanks. See appendixes for additional explanatory information.
Standard Classification System for and Basis for Specification for _____ Molding and Extrusion Materials (______)
1. Scope* concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and
1.1 This classification system covers ___ materials suitable
health practices and determine the applicability of regulatory
for _____________. The inclusion or exclusion of recycled
limitations prior to use.
plastics in this classification system must be addressed here.
1.2 The properties included in this standard are those
2. Referenced Documents
required to identify the compositions covered. Other require-
2
2.1 ASTM Standards:
ments necessary to identify particular characteristics important
D618 Practice for Conditioning Plastics for Testing
to specialized applications are to be specified by using the
D883 Terminology Relating to Plastics
suffixes as given in Section 5.
D1600 Terminology for Abbreviated Terms Relating to
1.3 This classification system and subsequent line callout
Plastics
(specification) are intended to provide a means of calling out
D3892 Practice for Packaging/Packing of Plastics
plastic materials used in the fabrication of end items or parts.
D4000 Classification System for Specifying Plastic Materi-
It is not intended for the selection of materials. Material
als
selection can be made by those having expertise in the plastic
D5205 Classification System for Polyetherimide (PEI) Ma-
field only after careful consideration of the design and the
terials
performance required of the part, the environment to which it
will be exposed, the fabrication process to be employed, the
NOTE 2—Omit if use of recycled plastic is not allowed.
costsinvolved,andtheinherentpropertiesofthematerialother
D5630 Test Method for Ash Content in Plastics
than those covered by this standard.
D6779 Classification System for Polyamide Molding and
Extrusion Materials (PA)
NOTE 1—Insert Note 1 here to show the appropriate ISO equivalency
D7209 Guide forWaste Reduction, Resource Recovery, and
statement.
Use of Recycled Polymeric Materials and Products
1.4 The following precautionary caveat pertains only to the
E29 Practice for Using Significant Digits in Test Data to
test method portion, Section 11, of this classification system:
Determine Conformance with Specifications
This standard does not purport to address all of the safety
1
This guide is under the jurisdiction of ASTM Committee D20 on Plastics and
is the direct responsibility of Subcommittee D20.94 on Government/Industry
2
Standardization. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2009. Published September 2009. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 1995. Last previous edition approved in 2003 as D5740 – 03. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D5740-09. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D5740 – 09
3
2.2 ISO Standards:
T Talcum 62%
V Metal 62%
ISO 3451–1 Plastics—Determination of Ash Content—Part
W Wood 62%
1: General Methods
X Not specified To be specified
3. Terminology
A
Ash content of filled and/or reinforced materials is to be determined using either
3.1 Except for the terms defined below, the terminology
Test Method D5630 or ISO 3451-1 where applicable.
B
Additional symbols will be added to this table as required.
used in this classification system is in accordance with Termi-
nologies D883 and D1600.
NOTE 4—This part of the classification system uses the percent of
reinforcements or additives, or both, in the callout of the modified basic
4. Classification
material. The types and percentages of reinforcements and additives are
sometimes shown on the supplier’s technical data sheet. If necessary,
4.1 ___ materials are cl
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D5740–03 Designation: D 5740 – 09
Standard Guide for
Writing Material Standards in the Classification D 4000
1
Format
This standard is issued under the fixed designation D 5740; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This guide has been prepared to aid in the writing of material standards using the Classification
D 4000 format. The following template is included which might be used directly for a draft document
simply by filling in the blanks. See appendixes for additional explanatory information.
Standard Classification System for _____ Molding and Extrusion Materials (______) Standard Classification System for
and Basis for Specification for _____ Molding and Extrusion Materials (______)
1. Scope*
1.1 This classification system covers ___ materials suitable for _____________.The inclusion or exclusion of recycled plastics
in this classification system must be addressed here.
1.2 The properties included in this standard are those required to identify the compositions covered. There may be other Other
requirements necessary to identify particular characteristics important to specialized applications. These mayapplications are to be
specified by using the suffixes as given in Section 5.
1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic
materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection shouldcan
be made by those having expertise in the plastic field only after careful consideration of the design and the performance required
ofthepart,theenvironmenttowhichitwillbeexposed,thefabricationprocesstobeemployed,thecostsinvolved,andtheinherent
properties of the material other than those covered by this standard.
NOTE 1—Insert Note 1 here to show the appropriate ISO equivalency statement.
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 618 Practice for Conditioning Plastics for Testing
D 883 Terminology Relating to Plastics
D 1600 Terminology for Abbreviated Terms Relating to Plastics
D 3892 Practice for Packaging/Packing of Plastics
D 4000 Classification System for Specifying Plastic Materials
3
D4066Specification for Nylon Injection and Extrusion Materials (PA)
D5033Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics 5205 Classification
System for Polyetherimide (PEI) Materials
NOTE 2—Omit if use of recycled plastic is not allowed.
1
This guide is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.94 on Government/Industry
Standardization.
Current edition approved July 10, 2003. Published October 2003. Originally approved in 1995. Last previous edition approved in 1997 as D5740–97.
Current edition approved Sept. 1, 2009. Published September 2009. Originally approved in 1995. Last previous edition approved in 2003 as D 5740 – 03.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 08.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D5740–09
D 5630 Test Method for Ash Content in Plastics
4
D 6779 Classification System for Polyamide Molding and Extrusion Materials (PA) Classification System for Polyamide
Molding and Extrusion Materials (PA)
D 7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
3
2.2 ISO Standards:
ISO 3451–1 Plastics—Determi
...