iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E3221-19

(Guide)

Standard Guide for Motorized Equipment

Standard Guide for Motorized Equipment

SIGNIFICANCE AND USE
5.1 Measuring and managing the effectiveness of a motorized equipment program will result in improved accountability and enhanced operational performance. Accountability will be evident through standard performance measures, such as cost savings, increased asset visibility and utilization, extended asset life, petroleum and greenhouse gas (GHG) reductions, and increased mission effectiveness.
SCOPE
1.1 This guide addresses considerations for effectively managing fleets of motorized mobile equipment assets.  
1.2 This guide primarily addresses nontactical motorized equipment but may also include other commodity groups such as aircraft and waterborne vessels.  
1.3 This guide does not override requirements specific to governmental authorities. However, to the greatest extent practicable, entities should consider the guidance in this standard where the opportunity to realize efficiencies is evident.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
14-Sep-2019
ICS
03.220.01 - Transport in general
Technical Committee
E53 - Asset Management
Drafting Committee
E53.08 - Management of Fleet Assets
Current Stage
Ref Project

Relations

Refers
ASTM E2608-20 - Standard Practice for Equipment Control Matrix (ECM)
Effective Date
01-Jul-2020
Refers
ASTM E2279-15 - Standard Practice for Establishing the Guiding Principles of Property Asset Management
Effective Date
01-Jan-2015
Refers
ASTM E2279-20 - Standard Practice for Establishing the Guiding Principles of Property Asset Management
Effective Date
01-Jul-2020
Refers
ASTM E2306-18 - Standard Guide for Disposal of Personal Property Assets
Effective Date
01-Jul-2018
Refers
ASTM E2135-10a(2017) - Standard Terminology for Property and Asset Management
Effective Date
01-May-2017
Refers
ASTM E2962-14(2020) - Standard Guide for Fleet Management
Effective Date
01-Jul-2020
Referred By
ASTM E2675-22 - Standard Practice for Asset Management System Outcomes
Effective Date
15-Sep-2019
Referred By
ASTM E2135-22 - Standard Terminology for Property and Asset Management
Effective Date
15-Sep-2019

Buy Standard

ASTM E3221-19 - Standard Guide for Motorized EquipmentASTM E3221-19 - Standard Guide for Motorized Equipment
PreviousNext
Guide
ASTM E3221-19 - Standard Guide for Motorized Equipment
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: E3221 − 19
Standard Guide for
1
Motorized Equipment
This standard is issued under the fixed designation E3221; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
1.1 This guide addresses considerations for effectively man- 3.1 Definitions—For definitions related to property and
aging fleets of motorized mobile equipment assets. assetmanagement,refertoTerminologyE2135.Fordefinitions
related to fleet management, refer to Terminology E2962.
1.2 This guide primarily addresses nontactical motorized
3.1.1 motorized equipment, n—grouping of similar,
equipment but may also include other commodity groups such
powered, operated assets designed for off-road and construc-
as aircraft and waterborne vessels.
tion purposes.
1.3 This guide does not override requirements specific to
3.1.1.1 Discussion—Typical groups include nontactical,
governmental authorities. However, to the greatest extent
motorized, off-road, and construction assets other than com-
practicable, entities should consider the guidance in this
mercially designed highway motor vehicles. Such an asset
standard where the opportunity to realize efficiencies is evi-
group may be restricted to one location or may be national or
dent.
international. Excluded from this definition are assets that have
1.4 This standard does not purport to address all of the
features ordinarily associated with military combat or tactical
safety concerns, if any, associated with its use. It is the
vehicles such as armor or weaponry, or both.Also excluded are
responsibility of the user of this standard to establish appro-
stationary powered equipment such as pumps, compressors,
priate safety, health, and environmental practices and deter-
and generators. The assets may be wheeled or tracked and
mine the applicability of regulatory limitations prior to use.
generally have an operator. Included are material handling and
1.5 This international standard was developed in accor-
construction equipment not designed and used primarily for
dance with internationally recognized principles on standard-
highway operation (that is, if it must be trailered or towed to be
ization established in the Decision on Principles for the
transported on public highways); equipment powered by inter-
Development of International Standards, Guides and Recom-
nal combustion engines or electric motors with combined
mendations issued by the World Trade Organization Technical
horsepower ≥23, or both. Examples are: construction, material
Barriers to Trade (TBT) Committee.
handling, well-drilling, and aircraft support equipment (for
example, de-icers, tugs, baggage carts, stairs); cranes (includ-
2. Referenced Documents
ing hydraulic boom and truck crane units); all-terrain vehicles
2
2.1 ASTM Standards:
and mobile generators (usually trailer-mounted).
E2135 Terminology for Property and Asset Management
3.1.1.2 fleet, n—grouping of similar assets that are designed
E2279 Practice for Establishing the Guiding Principles of
to be mobile.
Property Asset Management
E2306 Guide for Disposal of Personal Property Assets
3.1.1.3 heavy equipment, n—assets characterized as nontac-
E2608 Practice for Equipment Control Matrix (ECM)
tical heavy equipment fall under this standard within the
E2962 Guide for Fleet Management
Federal government, which has no generally accepted defini-
3
2.2 GAO Document:
tion for heavy or motorized equipment. However, most Federal
GAO-18-295 Heavy Equipment
government heavy equipment fit into one of five categories: (1)
construction, mining, excavating, and highway maintenance
1
This guide is under the jurisdiction of ASTM Committee E53 on Asset
equipment; (2) airfield-specialized trucks and trailers; (3)
Management and is the direct responsibility of Subcommittee E53.08 on Manage-
self-propelled warehouse trucks and tractors; (4) tractors; and
ment of Fleet Assets.
(5) soil preparation and harvesting equipment. (See GAO-18-
Current edition approved Sept. 15, 2019. Published October 2019. DOI:
295.)
10.1520/E3221–19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.1.1.4 yellow iron, n—assets that fit this common nontech-
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
nical (slang) industry description fall under this standard.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3.2 Abbreviations and Acronyms:
3
Availab
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2962-14(2020)(Guide)
Standard Guide for Fleet Management

SIGNIFICANCE AND USE
5.1 This guide promotes the considerations that may be applied to the management of fleet assets as a business process of the entity.  
5.2 The central objective of this guide is to ensure that fleet assets are managed in a manner best suited to the entity taking into account the needs and mission of the entity and the respective capabilities of the assets.  
5.3 Measuring and managing the effectiveness of a fleet program will result in improved accountability and enhanced operational performance. Accountability will be evident through standard performance measures such as cost savings, increased asset utilization, extended asset life, and increased mission effectiveness.
SCOPE
1.1 This guide addresses considerations for effectively managing fleets of mobile assets.  
1.2 This guide primarily addresses fleets of non-tactical motor vehicles and aircraft but may also include other commodity groups such as waterborne vessels and specialized mobile assets.  
1.3 This guide does not override or increase requirements specific to governmental authorities. However, to the greatest extent practicable, the guidance in this guide should be considered by these entities where efficiencies may be gained.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2962-14(2020)(Guide)
Standard Guide for Fleet Management

SIGNIFICANCE AND USE
5.1 This guide promotes the considerations that may be applied to the management of fleet assets as a business process of the entity.  
5.2 The central objective of this guide is to ensure that fleet assets are managed in a manner best suited to the entity taking into account the needs and mission of the entity and the respective capabilities of the assets.  
5.3 Measuring and managing the effectiveness of a fleet program will result in improved accountability and enhanced operational performance. Accountability will be evident through standard performance measures such as cost savings, increased asset utilization, extended asset life, and increased mission effectiveness.
SCOPE
1.1 This guide addresses considerations for effectively managing fleets of mobile assets.  
1.2 This guide primarily addresses fleets of non-tactical motor vehicles and aircraft but may also include other commodity groups such as waterborne vessels and specialized mobile assets.  
1.3 This guide does not override or increase requirements specific to governmental authorities. However, to the greatest extent practicable, the guidance in this guide should be considered by these entities where efficiencies may be gained.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM A370-23(Test Method)
Standard Test Methods and Definitions for Mechanical Testing of Steel Products

SIGNIFICANCE AND USE
4.1 The primary use of these test methods is testing to determine the specified mechanical properties of steel, stainless steel, and related alloy products for the evaluation of conformance of such products to a material specification under the jurisdiction of ASTM Committee A01 and its subcommittees as designated by a purchaser in a purchase order or contract.  
4.1.1 These test methods may be and are used by other ASTM Committees and other standards writing bodies for the purpose of conformance testing.  
4.1.2 The material condition at the time of testing, sampling frequency, specimen location and orientation, reporting requirements, and other test parameters are contained in the pertinent material specification or in a general requirement specification for the particular product form.  
4.1.3 Some material specifications require the use of additional test methods not described herein; in such cases, the required test method is described in that material specification or by reference to another appropriate test method standard.  
4.2 These test methods are also suitable to be used for testing of steel, stainless steel and related alloy materials for other purposes, such as incoming material acceptance testing by the purchaser or evaluation of components after service exposure.  
4.2.1 As with any mechanical testing, deviations from either specification limits or expected as-manufactured properties can occur for valid reasons besides deficiency of the original as-fabricated product. These reasons include, but are not limited to: subsequent service degradation from environmental exposure (for example, temperature, corrosion); static or cyclic service stress effects, mechanically-induced damage, material inhomogeneity, anisotropic structure, natural aging of select alloys, further processing not included in the specification, sampling limitations, and measuring equipment calibration uncertainty. There is statistical variation in all aspects of mechanical testin...
SCOPE
1.1 These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.  
1.2 The following mechanical tests are described:    
Sections  
Tension  
7 to 14  
Bend  
15  
Hardness  
16  
Brinell  
17  
Rockwell  
18  
Portable  
19  
Impact  
20 to 30  
Keywords  
32  
1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows:    
Annex  
Bar Products  
Annex A1  
Tubular Products  
Annex A2  
Fasteners  
Annex A3  
Round Wire Products  
Annex A4  
Significance of Notched-Bar Impact Testing  
Annex A5  
Converting Percentage Elongation of Round Specimens to
Equivalents for Flat Specimens  
Annex A6    
Testing Multi-Wire Strand  
Annex A7  
Rounding of Test Data  
Annex A8  
Methods for Testing Steel Reinforcing Bars  
Annex A9  
Procedure for Use and Control of Heat-cycle Simulation  
Annex A10  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 When these test methods are referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 in. or 8 in. may be report...

  • Standard
    51 pages
    English language
    sale 15% off
  • Standard
    51 pages
    English language
    sale 15% off
ASTM
ASTM D3495-10(2023)(Test Method)
Standard Test Method for Hexane Extraction of Leather

SIGNIFICANCE AND USE
3.1 This test method measures the amount of hexane-soluble lubricant present in all types of leather. Adequate lubrication prevents abrasion of leather fibers during flexing. This lubrication is generally obtained from the fat liquor added at the tannery. Some lubrication is also obtained from natural grease produced during the life of the animal.
SCOPE
1.1 This test method covers the quantitative extraction of all types of leather with hexane. This test method does not apply to wet blue.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F981-23(Practice)
Standard Practice for Assessment of Muscle and Bone Tissue Responses to Long-Term Implantable Materials Used in Medical Devices

SIGNIFICANCE AND USE
4.1 This practice is a guideline for short-term and long-term assessment of skeletal muscle and bone tissue responses to long-term implant materials. For testing of final finished medical devices, the test article for implantation shall be as for intended use, including packaging and sterilization. The tissue responses to the test article are compared to the skeletal muscle and/or bone tissue response(s) elicited by control materials. The controls consistently demonstrate known cellular reaction and wound healing.
SCOPE
1.1 This practice provides guidelines for biological assessment of tissue responses to nonabsorbable for medical device implants. It assesses the effects of the material that is implanted intramuscularly or intraosseously. The experimental protocol is not designed to provide a comprehensive assessment of the systemic toxicity, immune response, carcinogenicity, or mutagenicity of the material since other standards address these issues. It applies only to materials with projected applications in humans where the materials will reside in bone or skeletal muscle tissue in excess of 30 days. Applications in other organ systems or tissues may be inappropriate and are therefore excluded. Control materials are well recognized with a well-characterized long-term response and can include metals and any one of the metal alloys in Specification F67, F75, F90, F136, F138, or F562, high purity dense aluminum oxide as described in Specification F603, ultra high molecular weight polyethylene as stated in Specification F648, or USP polyethylene negative control.  
1.2 The values stated in SI units, including units officially accepted for use with SI, are to be regarded as standard. No other systems of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1157/C1157M-23(Specification)
Standard Performance Specification for Hydraulic Cement

SCOPE
1.1 This performance specification covers hydraulic cements for both general and special applications. There are no restrictions on the composition of the cement or its constituents (see Note 1).
Note 1: There are two related hydraulic cement standards, Specification C150/C150M for portland cement and Specifications C595/C595M for blended cements, both of which contain prescriptive and performance requirements  
1.2 This performance specification classifies cements based on specific requirements for general use, high early strength, resistance to attack by sulfates, and heat of hydration. Optional requirements are provided for the property of low reactivity with alkali-silica-reactive aggregates and for air-entraining cements.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice.  
1.4 The text of this performance specification refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) are not requirements of the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6182-23(Test Method)
Standard Test Method for Flexibility and Adhesion of Finish on Leather

SIGNIFICANCE AND USE
5.1 This test method is intended for use on any type of finished leather.  
5.2 This test method will give an indication of the flexibility, adhesion, and strength of the finish on leather.
SCOPE
1.1 This test method is intended for use on finished leather to evaluate resistance to cracking, delamination, and discoloration of the finish when subjected to repeated flexing. This test method does not apply to wet blue.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2675/F2675M-23(Test Method)
Standard Test Method for Determining Arc Ratings of Hand Protective Products Developed and Used for Electrical Arc Flash Protection

SIGNIFICANCE AND USE
5.1 This test method is intended for the determination of the arc rating of a hand protective product material, or a combination of hand protective product materials.  
5.1.1 Because of the variability of the arc exposure, different heat transmission values are observed at individual sensors. Evaluate the results of each sensor in accordance with Section 12.  
5.2 This test method maintains the specimen in a static, vertical position and does not involve movement except that resulting from the exposure.  
5.3 This test method specifies a standard set of exposure conditions. Different exposure conditions have the potential to produce different results. In addition to the standard set of exposure conditions, other conditions are allowed and shall be documented in the reporting of the testing results.
SCOPE
1.1 This test method is used to determine the arc rating of hand protective products in the form of gloves, glove materials, glove material systems, or other protective products designed to fit on the hand and specifically intended for electric arc flash protection use as protective accessories for workers exposed to electric arcs. The arc rating is determined in the test with an arc that has a heat flux value of 2100 kW/m2 [50 cal/cm2/s].  
1.2 This test method will determine the arc rating of hand protective products made of materials that meet the following requirements for flame resistance: less than 150 mm [6 in.] char length, less than 2 s afterflame and no melt and drip when tested in accordance with Test Method D6413, receive a reported 50 % probability of ignition of a material or flammable underlayer (see definition of ignition50) by this method, or that have been evaluated and pass the ignition withstand requirements of this test method.  
1.2.1 It is the intent of this test method to be used for hand protective products that are flame resistant or that have an adequate flame resistance for the required hazard (see 1.2). Non-flame resistant hand protective products may be used as under layers in multiple-layer systems or tested for ignition probability or ignition withstand.  
1.2.2 Hand protective products tested by this test method are new and ratings received by this method may be reduced or eliminated by hydrocarbon loading (gasoline, diesel fuel, transformer oil, etc.), sweat, dirt, grease, or other contaminants. The end user takes responsibility for use of hand protective products tested by this method when contaminated in such a manner that could reduce or eliminate the arc rating of the hand protective products.  
1.2.3 This test method is designed to provide information for gloves used for electric arc protection only. This test method is not suitable for determining electrical protective properties of hand protective products.  
1.3 This test method is used to measure and describe the properties of hand protective products in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions.  
1.4 This test method does not apply to electrical contact or electrical shock hazards.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined  
1.6 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment that takes into account all of the factors, which are pertinent to an assessment of the fire hazard of a particular end use.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this s...

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM F1911-05(2023)(Practice)
Standard Practice for Installation of Barbed Tape

SIGNIFICANCE AND USE
4.1 This practice is intended to provide standard requirements utilizing specialized equipment and hand tools.  
4.2 Ensure that the barbed tape is fabricated from acceptable material and well constructed. Field verification of the barbed tape's acceptability shall be in accordance with the project's specifications and this specification.
SCOPE
1.1 This practice covers the installation procedure for barbed tape.  
1.2 The primary purpose of this practice is to guide those responsible for or concerned with the installation of barbed tape on chain link fences, masonry walls, roofs or used as ground barriers. This standard is not intended to cover aspects of perimeter security for establishing levels of product performance or give analysis relating to various design comparisons.  
1.3 This standard involves the use of material, that may cause injury, including exposure to hazardous materials, and operation of specialized equipment.  
1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D4861-23(Practice)
Standard Practice for Sampling and Selection of Analytical Techniques for Pesticides and Polychlorinated Biphenyls in Air

SIGNIFICANCE AND USE
5.1 This practice is recommended for use primarily for non-occupational exposure monitoring in domiciles, public access buildings, and offices.  
5.2 The methods described in this practice have been successfully applied to measurement of pesticides and PCBs in outdoor air and for personal respiratory exposure monitoring.  
5.3 A broad spectrum of pesticides are commonly used in and around the house and for insect control in public and commercial buildings. Other semivolatile organic chemicals, such as PCBs, are also often present in indoor air, particularly in large office buildings. This practice promotes needed precision and bias in the determination of many of these airborne chemicals.
SCOPE
1.1 This practice covers the sampling of air for a variety of common pesticides and polychlorinated biphenyls (PCBs) and provides guidance on the selection of appropriate analytical measurement methods. Other compounds such as polychlorinated dibenzodioxins/furans, polybrominated biphenyls, polybrominated diphenyl ethers, polycyclic aromatic hydrocarbons, and polychlorinated naphthalenes may be efficiently collected from air by this practice, but guidance on their analytical determination is not covered by this practice.  
1.2 The sampling and analysis of PCBs in air can be more complicated than sampling PCBs in solid media (for example, soils, building materials) or liquids (for example, transformer fluids). PCBs in solid or liquid material are typically analyzed using Aroclor2 distillation groups in chromatograms. In contrast, recent research has shown that analysis of PCBs in air samples by GC-ECD has also been found to exhibit potential uncertainties due to changes in the PCB patterns, differences in responses in distillation groups, peak co-elutions and differences in response factors within a homolog group (1, 2).3 As such it is recommended that PCBs in air not be quantified using AroclorTM distillation groups. In addition, it is recommended that analysis of PCBs in air be done using GC-MS rather than GC-ECD. Any mention, to outdated practices for “Aroclor” and GC-ECD analysis of PCBs herein are retained solely for historical perspective.  
1.3 A complete listing of pesticides and other semivolatile organic chemicals for which this practice has been tested is shown in Table 1.  
1.4 This practice is based on the collection of chemicals from air onto polyurethane foam (PUF) or a combination of PUF and granular sorbent (for example, diphenyl oxide, styrene-divinylbenzene), or a granular sorbent alone.  
1.5 This practice is applicable to multicomponent atmospheres, 0.001 μg/m3 to 50 μg/m3 concentrations, and 4 h to 24 h sampling periods. The limit of detection will depend on the nature of the analyte and the length of the sampling period.  
1.6 The analytical method(s) recommended will depend on the specific chemical(s) sought, the concentration level, and the degree of specificity required.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see 10.24 and A1.1.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    16 pages
    English language
    sale 15% off