ASTM D5363-03

Standard Specification for Anaerobic Single-Component Adhesives (AN)

SCOPE
1.1 This specification covers single-component anaerobic adhesives suitable for locking, sealing, and retaining threaded or cylindrical assemblies. The adhesives are cured to a solid state when confined between closely fitting active metal surfaces.
1.2 This specification is intended to be a means of classifying anaerobic adhesives. It is not intended for engineering design purposes.
1.3 This specification is intended to replace Military Specifications MIL-S-22473, MIL-S-46163, and MIL-R-46082.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Nov-2003
• ICS: 83.180 - Adhesives
• Technical Committee: D14 - Adhesives
• Drafting Committee: D14.60 - Adhesive Material Classification System

Relations

• Replaces: ASTM D5363-97 - Standard Specification for Anaerobic Single-Component Adhesives (AN)
• Effective Date: 01-Dec-2003
• Replaced By: ASTM D5363-03e1 - Standard Specification for Anaerobic Single-Component Adhesives (AN)
• Effective Date: 01-Dec-2003
• Referred By: ASTM D4054-23 - Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
• Effective Date: 01-Dec-2003
• Referred By: ASTM D6465-99(2016) - Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
• Effective Date: 01-Dec-2003
• Referred By: ASTM D4800-94(2023) - Standard Guide for Classifying and Specifying Adhesives
• Effective Date: 01-Dec-2003

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 5363 – 03
Standard Specification for
1
Anaerobic Single-Component Adhesives (AN)
This standard is issued under the fixed designation D5363; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope and Opaque Liquids (and the Calculation of Dynamic
Viscosity)
1.1 This specification covers single-component anaerobic
D770 Specification for Isopropyl Alcohol
adhesives suitable for locking, sealing, and retaining threaded
D907 Terminology of Adhesives
or cylindrical assemblies. The adhesives are cured to a solid
D1084 Test Methods for Viscosity of Adhesives
state when confined between closely fitting active metal
D1193 Specification for Reagent Water
surfaces.
D2693 Specification for Ethylene Glycol
1.2 This specification is intended to be a means of classify-
D3951 Practice for Commercial Packaging
ing anaerobic adhesives. It is not intended for engineering
D4562 TestMethodforShearStrengthofAdhesivesUsing
design purposes.
Pin-and-Collar Specimen
1.3 This specification is intended to replace Military Speci-
D4800 Guide for Classifying and Specifying Adhesives
fications MIL-S-22473, MIL-S-46163, and MIL-R-46082.
D5648 Test Method for Torque-Tension Relationship of
1.4 The values stated in SI units are to be regarded as the
Adhesives Used on Threaded Fasteners (Lubricity)
standard.
D5649 TestMethodforTorqueStrengthofAdhesivesUsed
1.5 The following safety hazards caveat pertains only to the
on Threaded Fasteners
test methods portion, Section 7, of this specification. This
D5657 Test Method for Fluid Tightness Ability of Adhe-
standard does not purport to address all of the safety concerns,
sives Used on Threaded Fasteners
if any, associated with its use. It is the responsibility of the user
E122 Practice for Calculating Sample Size to Estimate.
of this standard to establish appropriate safety and health
With a Specified Tolerable Error, the Average for a
practices and determine the applicability of regulatory limita-
Characteristic of a Lot or Process
tions prior to use.
2.2 Military Standards:
2. Referenced Documents MIL-STD-105 Sampling Procedures and Tables for Inspec-
4
2
tion by Attributes
2.1 ASTM Standards:
4
MIL-STD-129 Marking for Shipment and Storage
A109/A109M Specification for Steel, Strip, Carbon, (0.25
MIL-STD-810 Environmental Test Methods and Engineer-
Maximum Percent) Cold-Rolled
4
ing Guides
B36/B36M SpecificationforBrassPlate,Sheet,Strip,and
MIL-STD-118 Commercial Packaging of Supplies and
Rolled Bar
4
Equipment
B209 Specification for Aluminum and Aluminum-Alloy
2.3 Federal Standards:
Sheet and Plate
FED-STD-313 Material Safety Data Sheets, Preparation
B633 Specification for Electrodeposited Coatings of Zinc
4
and Submission of
on Iron and Steel
2.4 Federal Specifications:
D56 Test Method for Flash Point by Tag Closed Tester
3
FF-N-836 Nut: Square, Hexagon, Cap, Slotted, Castle,
D439 Specification for Automotive Gasoline
4
Knurled, Welding and Single Ball Seat
D445 Test Method for Kinematic Viscosity of Transparent
4
PPP-B-636 Box, Shipping, Fiberboard
4
QQ-P-416 Plating, Cadmium, Electrodeposited
2.5 Military Specifications:
1
This specification is under the jurisdiction of ASTM Committee D14 on
MIL-R-46082 Retaining Compounds, Single-Component,
Adhesives and is the direct responsibility of Subcommittee D14.60 on Adhesive 4
Anaerobic
Material Classification System.
MIL-S-22473 Sealing, Locking, Retaining Compounds;
Current edition approved Dec. 1, 2003. Published January 2004. Originally
4
approved in 1993. Last previous edition approved in 1997 as D5363–97. Single-Component
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4
the ASTM website. Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
3
Withdrawn. Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D5363–03
MIL-S-46163 Sealing, Lubricating, and Wicking Com- torque is most often defined as the torque measured at 180°
4
pounds: Thread-Locking, Anaerobic, Single-Component rotationofthenut.However,forpurposesofthisspecification,
4
MIL-T-5624 Turbine Fuel,Aviation, Grades JP-4 and JP-5 the definition of prevailing torque as the average of the four
2.6 U.S. Department of Transportation (DOT): torques measured at 90, 180, 270, and 360° rotation of the nut
Code of Federal Reg
...