iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM A264-03

(Specification)

Specification for Stainless Chromium-Nickel Steel-Clad Plate

Specification for Stainless Chromium-Nickel Steel-Clad Plate

ABSTRACT
This specification covers the requirements for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of stainless chromium-nickel steel for pressure vessel. The steel shall be made by the open-heart, electric-furnace, or basic-oxygen processes and the alloy-cladding metal shall be metallurgically bonded to the base metal. The steel clad plate shall be heat treated. The steel specimens shall undergo tension test and shall conform to the required values of tensile strength and yield strength. The steel materials shall also undergo bend tests and shall conform to the required values of shear strength and bond strength. Product and chemical analyses shall also be performed on the steel specimens.
SCOPE
1.1 This specification covers plate, sheet, and strip of carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of stainless chromium-nickel steel. The material is generally intended for pressure vessel use.  
1.2 The values stated in inch-pound units are to be regarded as the standard. SI units are provided for information only.

General Information

Status
Historical
Publication Date
09-Feb-2003
ICS
77.140.50 - Flat steel products and semi-products
Technical Committee
A01 - Steel, Stainless Steel and Related Alloys
Drafting Committee
A01.11 - Steel Plates for Boilers and Pressure Vessels
Current Stage
Ref Project

Relations

Replaces
ASTM A264-94a(1999) - Standard Specification for Stainless Chromium-Nickel Steel-Clad Plate, Sheet, and Strip
Effective Date
10-Feb-2003
Replaced By
ASTM A264-09 - Specification for Stainless Chromium-Nickel Steel-Clad Plate
Effective Date
01-May-2009
Referred By
ASTM A20/A20M-20 - Standard Specification for General Requirements for Steel Plates for Pressure Vessels
Effective Date
10-Feb-2003
Referred By
ASTM A480/A480M-23a - Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
Effective Date
10-Feb-2003
Referred By
ASTM A578/A578M-17 - Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
Effective Date
10-Feb-2003

Buy Standard

ASTM A264-03 - Specification for Stainless Chromium-Nickel Steel-Clad PlateASTM A264-03 - Specification for Stainless Chromium-Nickel Steel-Clad Plate
PreviousNext
Technical specification
ASTM A264-03 - Specification for Stainless Chromium-Nickel Steel-Clad Plate
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 264 – 03
Standard Specification for
1
Stainless Chromium-Nickel Steel-Clad Plate
This standard is issued under the fixed designation A 264; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 3. Terminology
2
1.1 This specification covers plate of a carbon steel or 3.1 Definitions of Terms Specific to This Standard:
low-alloy steel base to which is integrally and continuously 3.1.1 This material is considered as single-clad or double-
bonded on one or both sides a layer of stainless chromium- clad corrosion-resisting chromium-nickel steel plate, depend-
nickel steel. The material is generally intended for pressure ing on whether one or both sides are covered.
vessel use. 3.1.2 base metal (backing steel)—component to which the
1.2 The values stated in inch-pound units are to be regarded alloy cladding is applied, usually the greater percentage of the
as the standard. SI units are provided for information only. composite plate and usually consisting of carbon or low-alloy
steel.
2. Referenced Documents
3.1.3 alloy cladding—the stainless chromium-nickel steel
2.1 ASTM Standards:
component of the composite plate.
A 6/A 6M Specification for General Requirements for 3.1.4 integrally and continuously bonded—the process by
Rolled Structural Steel Bars, Plates, Shapes, and Sheet
whichthealloycladdingandbasemetalarebroughttogetherto
3
Piling form a metallurgical bond at essentially the entire interface of
A 20/A 20M Specification for General Requirements for
the two metals by means other than those processes that do not
3
Steel Plates for Pressure Vessels produce a homogeneous composite plate.
A 240/A 240M Specification for Chromium and
4. Ordering Information
Chromium-Nickel Stainless Steel Plate, Sheet, and Strip
4
for Pressure Vessels and for General Applications 4.1 It is the responsibility of the purchaser to specify all
A 370 Test Methods and Definitions for MechanicalTesting requirements that are necessary for material ordered under this
4
of Steel Products specification. Such requirements may include, but are not
A 480/A 480M Specification for General Requirements for limited to, the following:
Flat-Rolled Stainless and Heat-Resisting Steel Plate, 4.1.1 Quantity (weight or number of pieces),
4
Sheet, and Strip 4.1.2 Cladding alloy specification, (UNS or ASTM Specifi-
A 578/A 578M Specification for Straight-Beam Ultrasonic cation A 240/A 240M and whether cladding is for corrosion
Examination of Plain and Clad Steel Plates for Special allowance only),
3
Applications 4.1.3 Base metal specification,
A 751 Test Methods, Practices, and Terminology for 4.1.4 Bond integrity Class (1, 3, or 5),
4
Chemical Analysis of Steel Products 4.1.5 Dimensions including the minimum or nominal thick-
2.2 ASME Code: ness of the cladding alloy, and the backing steel, or of the total
Boiler and Pressure Vessel Code, Section IX, Welding composite plate and if more or less restrictive thickness
5
Qualifications tolerances apply,
4.1.6 Product analysis, if required (see Section 10). Specify
whether applicable to the cladding alloy, backing steel or both,
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
4.1.7 Mechanicalproperties,includingsheartestifrequired,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
4.1.8 Finish (see Section 12),
A01.11 on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Feb. 2, 2006. Published April 2003. Originally
4.1.9 Restrictions, if required, on repair by welding (see
approved in 1943. Last previous edition approved in 1999 as A 264 – 94a (1999).
Section 14),
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
4.1.10 Additions to the specification or special require-
cation SA-264 in Section II of that Code.
3
Annual Book of ASTM Standards, Vol 01.04. ments, and
4
Annual Book of ASTM Standards, Vol 01.03.
4.1.11 Corrosion testing if applicable.
5
Available from American Society of Mechanical Engineers (ASME), ASME
International Headquarters, Three Park Ave., New York, NY 10016-5990.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 264–03
4.2 Inadditiontothebasicrequirementsofthisspecification and the manufacturer. The base metal shall conform to the
and the backing steel specification, certain supplementary chem
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM A414/A414M-23(Specification)
Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels

ABSTRACT
This specification covers hot-rolled carbon steel sheet for pressure vessels involving fusion welding or brazing. Tensile and yield strengths shall be determined after a tension test of the sheets. The material shall be furnished without removing the hot-rolled oxide or scale. When required, the material may be specified to be pickled or blast cleaned. When specified to be pickled or blast cleaned, the material shall be furnished oiled. When required, pickled or blast-cleaned material may be specified to be furnished dry.
SCOPE
1.1 This specification2 covers hot-rolled carbon steel sheet for pressure vessels involving fusion welding or brazing. Welding and brazing technique is of fundamental importance and shall be in accordance with commercial practices.  
1.2 The following grades are included in this specification:    
Mechanical Requirements  
Yield Strength, min  
Tensile Strength, min  
Grade  
ksi  
MPa  
ksi  
MPa  
A  
25  
170  
45  
310  
B  
30  
205  
50  
345  
C  
33  
230  
55  
380  
D  
35  
240  
60  
415  
E  
38  
260  
65  
450  
F  
42  
290  
70  
485  
G  
45  
310  
75  
515  
H  
45  
310  
75  
515  
1.3 Hot-rolled carbon steel sheet is generally furnished in cut lengths and to decimal thickness only. Coils may be furnished, provided tension test specimens are taken to represent the middle of the slab as required by 6.1.3. The purchaser should recognize this may require cutting the coils to obtain test samples and results in half-size coils. The sheet is furnished to the following size limits:    
Width, in. [mm]    
Thickness, in. [mm]  
Over 12 [Over 300]    
0.270 to 0.230 [7.0 to 6.0]  
sheet (coils only)  
Under 0.230 to 0.057 [6.0 to 1.5]  
sheet  
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.5 Tolerances are found in General Requirements Specifications A568/A568M and A635/A635M. The appropriate General Requirements specification is applied based on the thickness and width of the product ordered.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM A1083/A1083M-23(Specification)
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, Produced by Twin-Roll Casting Process

ABSTRACT
This specification covers cold-rolled, carbon, structural, and high-strength low-alloy, in coils and cut lengths produced by the twin-roll casting process. Cold-rolled steel sheet is available in the following designations: commercial steel, drawing steel, structural steel, and high-strength low-alloy steel. Sheet steel grades defined by this specification are suitable for welding if appropriate welding conditions are selected. For certain welding processes, if more restrictive composition limits are desirable, they shall be specified at the time of inquiry and confirmed at the time of ordering. The material shall be capable of being bent, at room temperature, in any direction through 180° flat on itself without cracking on the outside of the bent portion. Two tension tests shall be made from each heat or from each 50 tons [45,000 kg]. Yield strength shall be determined by either the 0.2 % offset method or the 0.5 % extension under load method unless otherwise specified.
SCOPE
1.1 This specification covers cold-rolled, carbon, structural, and high-strength low-alloy, in coils and cut lengths produced by the twin-roll casting process.  
1.2 Cold rolled steel sheet produced by the twin-roll casting process is available in the designations as listed in 4.1.  
1.3 This specification does not apply to steel strip as described in Specification A109/A109M.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM A480/A480M-23b(Specification)
Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip

ABSTRACT
This specification covers general requirements for flat-rolled stainless and heat-resisting steel plate, sheet, and strip. The steel shall be made by one of the following processes: electric-arc, electric-induction, or other suitable processes. Heat and product analyses shall conform to the chemical requirements for each of the specific elements. The material shall undergo mechanical tests such as tension test, hardness test, and bend test. Special tests like intergranular corrosion test, permeability test, Charpy impact testing and tests for detrimental intermetallic phases in wrought duplex stainless steels shall be also be performed when required.
SCOPE
1.1 This specification2 covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued by ASTM: Specifications A240/A240M, A263, A264, A265, A666, A693, A793, and A895.  
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The SI units are shown in brackets, except that when A480M is specified, Annex A3 shall apply for the dimensional tolerances and not the bracketed SI values in Annex A2. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This specification and the applicable material specifications are expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished in inch-pound units.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    26 pages
    English language
    sale 15% off
  • Technical specification
    26 pages
    English language
    sale 15% off
ASTM
ASTM A1034/A1034M-23(Test Method)
Standard Test Methods for Testing Mechanical Splices for Steel Reinforcing Bars

SIGNIFICANCE AND USE
5.1 Significance:  
5.1.1 The bar-splice assembly test specimen shall closely represent the mechanical splice used in practice. The behavior of the bar-splice assembly embedded in concrete, however, may differ from its behavior during testing where it is not embedded in concrete.  
5.2 Usefulness:  
5.2.1 Testing of mechanical splices for reinforcing bars shall establish the behavior of the bar-splice assembly under the loading conditions described herein for the various test methods to determine the acceptability of the mechanical splice for use in reinforced concrete structural members under specific design criteria.  
5.3 Interpretation of Test Results:  
5.3.1 Similar or better performance of mechanical splices installed in structural members shall be expected only if materials and methods of assembly are similar to the materials and methods used in the tests.
SCOPE
1.1 These test methods cover the testing of mechanical splices for reinforcing bars. The various tests herein described can be specified in total or individually.  
1.2 The test methods herein described are applicable to any type of mechanical splice manufactured to join steel reinforcing bars of any grade (specified minimum yield strength), uncoated or coated.  
1.3 This standard describes only the methods for testing mechanical splices for steel reinforcing bars, but does not quantify the parameters for testing nor acceptance criteria, which must be specified.
Note 1: Various code-writing bodies specify various parameters, such as test loads, number of cycles and test temperature, for testing.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM A203/A203M-23(Specification)
Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel

ABSTRACT
This specification covers nickel-alloy steel plates intended primarily for welded pressure vessels. As a steel making practice, the steel shall be killed and shall conform to fine grain size requirements. The heat treatment requirements for all plates are presented, and all plates under Grades A, B, D, and E shall be normalized as required. The steel shall conform to the required chemical compositions. Two mechanical test requirements are presented that includes, tension test requirements and impact test requirements.
SCOPE
1.1 This specification2 covers nickel-alloy steel plates intended primarily for welded pressure vessels.  
1.2 Plates under this specification are available with four strength levels and two nickel compositions as follows:    
Grade  
Nominal Nickel
Content %  
Yield Strength, min, ksi [MPa]  
Tensile Strength, min, ksi [MPa]  
A  
2.25  
37 [255]  
65 [450]  
B  
2.25  
40 [275]  
70 [485]  
D  
3.50  
37 [255]  
65 [450]  
E  
3.50  
40 [275]  
70 [485]  
F  
3.50  
2 in. [50 mm] and under  
55 [380]  
80 [550]  
Over 2 in. [50 mm]  
50 [345]  
75 [515]  
1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.  
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A606/A606M-23(Specification)
Standard Specification for Steel, Sheet and Strip, High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, with Improved Atmospheric Corrosion Resistance

ABSTRACT
This specification covers standards for high-strength, low-alloy, hot-rolled and cold-rolled steel sheets and strips cut in lengths or coils for structural and miscellaneous purposes. The material shall come in Types 2 and 4 steels having enhanced atmospheric corrosion resistance. The material shall follow specified carbon, manganese, and sulfur contents. Tension test shall be performed and material shall comply with tensile strength, yield strength, and elongation requirements. Edges and surface finish of the materials shall conform to specifications. Guidelines for retests are also given.
SCOPE
1.1 This specification covers high-strength, low-alloy, cold-rolled sheet and strip in cut lengths or coils, hot-rolled sheet and strip steel in cut lengths or coils with ordered thickness less than 0.230 in. [6.0 mm], and hot-rolled sheet coils (not cut lengths) with ordered thickness 0.230 in. [6.0 mm] and thicker, intended for use in structural and miscellaneous purposes, where savings in weight or added durability are important. These steels have enhanced atmospheric corrosion resistance and are supplied in three types or as commercial steel (CS). Type 2 contains 0.20 % minimum copper based on cast or heat analysis (0.18 % minimum Cu for product check). Type 4 and Type 5 contain additional alloying elements and provide a level of corrosion resistance substantially better than that of carbon steels with or without copper addition (Note 1). When properly exposed to the atmosphere, Type 4 and Type 5 steels can be used in the bare (unpainted) condition for many applications. CS is intended for applications that require enhanced atmospheric corrosion resistance which do not require a specified strength. CS shall contain the chemical requirements of Type 2, Type 4, or Type 5. CS as contained within this specification is not associated with the requirements of CS that are referenced in other Subcommittee A01.19 on Steel Sheet and Strip specifications.
Note 1: For methods of establishing the atmospheric corrosion resistance of low-alloy steels, see Guide G101.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 Welding—In general, the steels listed in this specification are weldable with commonly obtained welding electrodes. When the steel is to be welded, a suitable welding procedure based on its composition should be used, taking into account intended use and service temperatures.
Note 2: For a general discussion of the weldability of steel and carbon equivalents, consult Appendix X3 of A6/A6M.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM A950/A950M-11(2023)(Specification)
Standard Specification for Fusion-Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling

ABSTRACT
This specification covers the qualification requirements for structural steel H-piles and sheet piling with protective fusion-bonded epoxy coating applied by electrostatic spraying, flocking, or fluidized bed processing. Surface preparation techniques shall be performed by abrasive blast cleaning, grinding and chemical washing prior to coating application. The powder coating shall be heat treated and cured before visible oxidation occurs. Coating materials shall undergo thickness measurements and bend testing, and shall conform to the requirements for film thickness, flexibility and continuity, impact resistance, chemical composition, and corrosion resistance. The coated H-piles or sheet piling shall be stored off of the ground on supports. While handling equipment, bundling bands for packaging and tie-down bands for shipping shall have padded contact areas so as to avoid damage and excessive deflection.
SCOPE
1.1 This specification covers structural steel H-piles and sheet piling with protective fusion-bonded epoxy coating applied by the electrostatic spray, flocking, or fluidized bed process.  
Note 1: The coating applicator is identified throughout this specification as the manufacturer.  
1.2 Requirements for coatings are contained in Annex A1.  
1.3 This specification is applicable for orders in either inch-pound units (as Specification A950) or SI units (as Specification A950M). The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM A666-23(Specification)
Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

ABSTRACT
This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions. They shall be formed in different shapes such as sheets, strips, plates and flat bars. The steels shall adhere to specified chemical composition requirements. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined. The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test.
SCOPE
1.1 This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions for various structural, pressure vessel, magnetic, cryogenic, and heat-resisting applications.  
1.2 The application of this specification, or the use of material covered by this specification does not automatically allow usage in pressure vessel applications. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM A553/A553M-22(Specification)
Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7 %, 8 %, and 9 % Nickel

ABSTRACT
This specification covers 8 and 9% nickel alloy steel plates for use in the water quenched and tempered condition intended for the fabrication of welded pressure vessels. The materials shall be available in two types, namely Type I and II, having different chemical compositions. The maximum thickness of plates is limited only by the capacity of the material to meet the specified mechanical property requirements. The material is susceptible to magnetization and the use of magnets in handling after heat treatment should be avoided if residual magnetism would be detrimental to subsequent fabrication or service. The steels shall be killed and shall conform to the fine austenitic grain size requirement specified. The plates shall be tempered and hardened by heat treatment. The specimens shall be subjected to tension and Charpy V-notch impact tests.
SCOPE
1.1 This specification2 covers 7 %, 8 %, and 9 % nickel alloy steel plates for use in the water quenched and tempered condition intended for the fabrication of welded pressure vessels.  
1.2 Material under this specification is available in three types having different chemical composition as follows:    
Type  
Nominal Nickel Content, %  
I  
9  
II  
8    
III  
7  
1.3 Plates produced under this specification are subject to impact testing at −320 °F [−195 °C] for Type I or Type III, and −275 °F [−170 °C] for Type II; or at such other temperatures as are agreed upon.  
1.4 The maximum thickness of plates is limited only by the capacity of the material to meet the specified mechanical property requirements.  
1.5 This material is susceptible to magnetization. Use of magnets in handling after heat treatment should be avoided if residual magnetism would be detrimental to subsequent fabrication or service.  
1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM A659/A659M-22(Specification)
Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled

ABSTRACT
This specification covers hot-rolled carbon steel sheet and strip, in coils and cut lengths. The cast or heat analysis of the steel shall conform to the chemical composition for copper, nickel, chromium, molybdenum, vanadium, and columbium. The bending properties are measured.
SCOPE
1.1 This specification covers hot-rolled carbon steel (CS) sheet and strip, in coils and cut lengths, in which the maximum of the specified carbon range is over 0.15 and not over 0.25 % and the maximum of the specified manganese range is not over 0.90 %. This material is ordered to chemical composition.  
1.2 This specification is not applicable to the steels covered by Specification A635/A635M.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off