ASTM F606-11a
(Test Method)Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ABSTRACT
These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets. These test methods shall be as follows: externally threaded fasteners; internally threaded fasteners; washers and direct tension indicators; rivets; test for embrittlement of metallic-coated externally threaded fasteners; and determining decarburization and carburization.
SCOPE
1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets.
1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F606 − 11a
StandardTest Methods for
Determining the Mechanical Properties of Externally and
Internally Threaded Fasteners, Washers, Direct Tension
1
Indicators, and Rivets
ThisstandardisissuedunderthefixeddesignationF606;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
Test Method for Determining Decarburization and Carburization 8
1.1 These test methods cover establishment of procedures
1.4 The values stated in inch-pound units are to be regarded
for conducting tests to determine the mechanical properties of
asstandard.Nootherunitsofmeasurementareincludedinthis
externally and internally threaded fasteners, washers, direct
standard.
tension indicators, and rivets.
NOTE1—AcompletemetriccompaniontoTestMethodsF606hasbeen
1.2 Property requirements and the applicable tests for their
developed—F606M; therefore, no metric equivalents are shown in these
test methods.
determination are specified in individual product standards. In
those instances where the testing requirements are unique or at
1.5 This standard does not purport to address all of the
variance with these standard procedures, the product standard
safety concerns, if any, associated with its use. It is the
shall specify the controlling testing requirements.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
1.3 These test methods describe mechanical tests for deter-
bility of regulatory limitations prior to use.
mining the following properties:
Section
For Externally Threaded Fasteners: 3
2. Referenced Documents
Product Hardness 3.1
2
Proof Load 3.2.1
2.1 ASTM Standards:
Method 1, Length Measurement 3.2.3
A394Specification for Steel Transmission Tower Bolts,
Method 2, Yield Strength 3.2.4
Zinc-Coated and Bare
Method 3, Uniform Hardness 3.2.5
Axial Tension Testing of Full-Size Product 3.4 E4Practices for Force Verification of Testing Machines
Wedge Tension Testing of Full-Size Product 3.5
E8Test Methods for Tension Testing of Metallic Materials
Tension Testing of Machined Test Specimens 3.6
E10Test Method for Brinell Hardness of Metallic Materials
Total Extension at Fracture Test 3.7
Single Sheer Test 3.8
E18Test Methods for Rockwell Hardness of Metallic Ma-
For Internally Threaded Fasteners: 4
terials
Product Hardness 4.1
E83Practice for Verification and Classification of Exten-
Proof Load Test 4.2
Cone Proof Load Test 4.3
someter Systems
For Washers and Direct Tension Indicators: 5
E92TestMethodforVickersHardnessofMetallicMaterials
Product Hardness-General Requirements 5.1
E384Test Method for Knoop and Vickers Hardness of
Through Hardened Washers 5.2
Carburized Washers 5.3
Materials
Stainless Steel and Nonferrous Washers 5.4
F436Specification for Hardened Steel Washers
Direct Tension Indicators 5.5
F606MTest Methods for Determining the Mechanical Prop-
Compression Load 5.6
For Rivets: 6
erties of Externally and Internally Threaded Fasteners,
Product Hardness 6.1
Washers, and Rivets (Metric)
Test for Embrittlement of Metallic-Coated Externally Threaded 7
F959Specification for Compressible-Washer-Type Direct
Fasteners
Tension Indicators for Use with Structural Fasteners
1
These test methods are under the jurisdiction of ASTM Committee F16 on
Fasteners and are the direct responsibility of Subcommittee F16.01 on Test
2
Methods. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 1, 2011. Published November 2011. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1979. Last previous edition approved in 2011 as F606–11. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F0606-11A. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F606 − 11a
F1624Test Method for Measurement of Hydrogen Em- 3.1.1.4 The Rockwell Hardness Scale may be used for all
brittlement Threshold in Steel by the Incremental Step product diameters; however, the Brinell hardness is limited to
1
Loading Technique products over 1 ⁄2-in. nominal diameter.
F2328Test Method for Determining Decarburization and
3.1.2 LaboratoryInspection—Afterobserving3.1and3.1.1,
Carburization in Hardened and Tempered Threaded Steel
a minimum of three readings shall be taken on each sample of
Bolts, Screws and Studs
finished pro
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:F606–11 Designation:F606–11a
Standard Test Methods for
Determining the Mechanical Properties of Externally and
Internally Threaded Fasteners, Washers, Direct Tension
1
Indicators, and Rivets
ThisstandardisissuedunderthefixeddesignationF606;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of
externally and internally threaded fasteners, washers, direct tension indicators, and rivets.
1.2 Propertyrequirementsandtheapplicabletestsfortheirdeterminationarespecifiedinindividualproductstandards.Inthose
instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall
specify the controlling testing requirements.
1.3 These test methods describe mechanical tests for determining the following properties:
Section
For Externally Threaded Fasteners: 3
Product Hardness 3.1
Proof Load 3.2.1
Method 1, Length Measurement 3.2.3
Method 2, Yield Strength 3.2.4
Method 3, Uniform Hardness 3.2.5
Axial Tension Testing of Full-Size Product 3.4
Wedge Tension Testing of Full-Size Product 3.5
Tension Testing of Machined Test Specimens 3.6
Total Extension at Fracture Test 3.7
Single Sheer Test 3.8
For Internally Threaded Fasteners: 4
Product Hardness 4.1
Proof Load Test 4.2
Cone Proof Load Test 4.3
For Washers and Direct Tension Indicators: 5
Product Hardness-General Requirements 5.1
Through Hardened Washers 5.2
Carburized Washers 5.3
Stainless Steel and Nonferrous Washers 5.4
Direct Tension Indicators 5.5
Compression Load 5.6
For Rivets: 6
Product Hardness 6.1
Test for Embrittlement of Metallic-Coated Externally Threaded 7
Fasteners
Test Method for Determining Decarburization and Carburization 8
1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
NOTE 1—Acomplete metric companion to Test Methods F606 has been developed—F606M; therefore, no metric equivalents are shown in these test
methods.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1
These test methods are under the jurisdiction of ASTM Committee F16 on Fasteners and are the direct responsibility of Subcommittee F16.01 on Test Methods.
Current edition approved May 15,Nov. 1, 2011. Published JuneNovember 2011. Originally approved in 1979. Last previous edition approved in 20102011 as
F606–10a.F606–11. DOI: 10.1520/F0606-11A.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F606–11a
2. Referenced Documents
2
2.1 ASTM Standards:
A394 Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare
E4 Practices for Force Verification of Testing Machines
E8 Test Methods for Tension Testing of Metallic Materials
E10 Test Method for Brinell Hardness of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E83 Practice for Verification and Classification of Extensometer Systems
E92 Test Method for Vickers Hardness of Metallic Materials
E384 Test Method for Knoop and Vickers Hardness of Materials
F436 Specification for Hardened Steel Washers
F606M TestMethodsforDeterminingtheMechanicalPropertiesofExternallyandInternallyThreadedFasteners,Washers,and
Rivets (Metric)
F959 Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
F1624 Test Method for Measurement of Hydrogen Embrittlement Threshold in Steel by the Incremental Step Loading
Technique
F2328 Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts,
Screws and Studs
3
2.2 Military Standard:
MIL STD1312, Test 13 and Test 20
3. Test Methods for Externally Threaded Fasteners
3.1 Product Hardness—Tests shall be conducted after the removal of any surface oxide, decarburization, plating o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.