ASTM A619/A619M-97

Standard Specification for Non-Killed Forming Steel (NKFS) Sheet, Carbon Cold-Rolled (Withdrawn 1997)

SCOPE
1.1 This specification covers cold-rolled carbon non-killed forming steel (NKFS) sheet in coils or cut lengths. The material is intended for fabricating identified parts where drawing or severe forming may be involved.  
1.2 This specification is applicable for orders in either inch-pound units (as A 619) or SI units (A 619M).

General Information

• Status: Withdrawn
• Publication Date: 09-Mar-1997
• Withdrawal Date: 09-Nov-1997
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.19 - Steel Sheet and Strip

Standards Content (Sample)

STD-ASTM Ab17/AbLSM-ENGL 3777 0759530 UbU7828 879
AMERICAN SOCIETY FOR TESTING AND MATERIALS
(cn(, Designation: A 619/A 619M - 97
100 Em Harbor Dr. West Conshohocken, PA 19428
Reprinted fmm the Annual Bûck of ASTM Standards. Copywht ASTM
Standard Specification for
Non-Killed Forming Steel (NKFS) Sheet, Carbon, Cold-Rolled’
This standard is issued under the ñxed designation A 619/A 619M the number immediately fdowhg the designation indicaies lhe
year of onginai adoption or, in the case of revision, the year of last revision. A number in parentheses indiortes the year of last
reapproval. A superszript &on (E) indicaies an editorial change anœ the kst reVision or mappmval.
This specuicnion has been approved for use by agencies of lhe Dak~ímeni of Dc$ense. Consult the DoD Index of Spec@îuUions and
S:andar& for the speciific year of issue which has been adopted by the Depulnmü qfoefmpe.
5.1.2 Name of material (cold-roiled non-Wed forming
1. scope
steel (NKFS) sheet),
1. I This specification covers cold-rolled carbon non-killed
5.1.3 Classification (either exposed, unexposed, temper
forming steel (NKFS) sheet in coils or cut lengths. The
rolled, or annealed last) (see 4.1),
material is intended for fabricating identified parts where
5.1.4 Finish (matte finish wili be supplied on exposed,
drawing or severe forming may be involved.
unless othenvise specified, and on unexposed) (see 10. i),
1.2 This specification is applicable for orders in either
5.1.5 Oiling (material wiìl be oiled unless ordered not
inch-pound units (as A 619) or SI units (A 6 19M).
oiled) (see 10.2),
5.1.6 Dimensions (thickness, width, and whether cut
2. Referenced Documents
lengths or coils),
2.1 ASTM Standards:
5.1.6.1 As agreed upon between the purchaser and the
A 568 /A 568M Specification for Steel, Sheet, Carbon, and
producer, material ordered to this specification wiìl be
High-Strength, Low-AUoy, Hot-Rolled and Cold-Rolled,
supplied to meet the appropriate standard or restricted
General Requirements for2
thickness tolerance table shown in Specification A568/
A 620fA 620M Specification for Drawing Steel (DS),
A 568M.
Sheet, Carbon, Cold-Rolled2
N~E 1-Not aii producers are capabíe of meeting all of the
limitations of the thicknes tolerance tables in Specification A5681
3. Terminology
A 568M. The purchaser should contact the producer regarding possible
3.1 Definitions:
limitations prior to placing an order.
3.1.1 aging-loss of ductility with an increase in hard-
5.1.7 Coil size (must include inside diameter, outside
ness, yield point, and tensile strength that occur when steel,
diameter, and maximum mass),
which has been slightly cold worked (such as by temper
5.1.8 Quantity,
rolling), is stored for some time. Aging also increases the
5.1.9 Application (show part identification and descrip
tendency toward stretcher strains and fluting.
tion),
3. I .2 non-killed forming steel (NKFS)-sheet manufäc-
5.1.10 Special requirements (ifrequired), and
tured from specially produced or selected steels speciaily
5. I. 1 1 Cast or heat anaiysis report (request, if required).
processed to have good uniform drawing properties for use in
fabricating an identified part having severe deformations. NOTE 2-A typical ordering description is as follows:
“ASTM A619-XX [or A6 igM-XX], Cold-Rolled Non-Killed
Forming Steel (NKFS) Sheet, exposed, oiled, 0.035 nominai by 53 in.
4. Classification
4.1 Cold-rolled sheet is supplied for either exposed or
TABLE 1 ChemicalRequirements
unexposed applications. Within the latter category, cold-
Element composition-weiaht % Heat AnalydS
rolled sheet is specified either “temper rolled” or “annealed
0.02fO.1 o
last.” For details on processing, attributes and limitations,
0.50
and inspection standards, refer to Specitications A568/
0.020
A 568M.
0.030
.. .
...
5. Ordering Information
020
5.1 It is the purchaser’s responsibiliS to specisl in the
0.20
purchase order dl ordering information necmary to pur- 0.15
0.06
chase the needed material. Examples of such information
0.008
include but are not limited to the following:
0.008
5.1.1 ASTM specification number and year of issue,
0.008
This specincation is under the jllrisdiction of ASTM Cornmittee A-1 on Steel,
Staides Steel and Reiated AUoys, and is lhe direct responsibiüty of Subcommittee
A01.19 on Steel Sheet and Strip.
Current edition approved March 10. 1997. Published November 1997. Chigi-
nally published as A 619 - 68. Replaws portions of A 365. Last previous edition
A 6191A619M-96.
Annual Book of ASTM Slanaàrds, Vol O i .03.
1

---------------------- Page: 1 ----------------------
em A 619/A 619M
[or 0.8 nominal by 1340 mm] standard thickness tolerance, by coil ID
ability of the material to form identified parts within
24 in., OD 48 in., max., weight I5 O00 ib, ma., [or coil ID 600 mm, OD
properly established breakage limits. (Refer to Appendix X4
1200 mm. max., weight 6800
...