ASTM D5813-04(2008)

Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems

ABSTRACT
This specification covers cured-in-place thermosetting resin pipe (CIPP) with a certain measurement, equivalent diameter, for use in gravity flow systems in conveying sanitary sewage, storm water, and certain industrial wastes. This specification is suited for the evaluation and testing of materials used in the rehabilitation of existing pipes by the installation and cure of a resin-impregnated fabric liner. CIPP are classified into three types: Type I which is designed to provide chemical resistance and prevent exfiltration; Type II which is installed in a partially deteriorated existing pipe or structure and is designed to provide chemical resistance, prevent exfiltration and infiltration, and support the external hydrostatic loads due to groundwater only (and internal vacuum, where applicable), since the soil and live loads can be supported by the original conduit or structure; and Type III which is Installed in a fully deteriorated existing pipe or structure and designed to provide chemical resistance, prevent exfiltration and infiltration, and support all external hydraulic, soil, and live loads acting on the original conduit or structure. CIPP also are classified into three grades: Grade 1 as thermosetting polyester resin, Grade 2 as thermosetting polyester resin, and Grade 3 as thermosetting epoxy resin. Properties of CIPP materials such as diameter, wall thickness, chemical resistance, flexural strength, and tensile strength shall be determined by subjecting them to different tests.
SCOPE
1.1 This specification covers cured-in-place thermosetting resin pipe (CIPP), 4 through 132-in. (100 through 3353-mm) equivalent diameter, for use in gravity flow systems for conveying sanitary sewage, storm water, and certain industrial wastes. This specification is suited for the evaluation and testing of materials used in the rehabilitation of existing pipes by the installation and cure of a resin-impregnated fabric liner.  
1.2 This specification can also be extended to cover manholes, pump stations, wetwells, vaults, storage tanks, and other similar structures where a cured in place liner using thermosetting resin is applicable.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1—There are no ISO standards covering the primary subject matter of this specification.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 14-Dec-2008
• Technical Committee: D20 - Plastics
• Drafting Committee: D20.23 - Reinforced Thermosetting Resin Piping Systems and Chemical Equipment

Relations

• Replaces: ASTM D5813-04 - Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
• Effective Date: 15-Dec-2008
• Replaced By: ASTM D5813-04(2012) - Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
• Effective Date: 01-Oct-2012
• Referred By: ASTM F2019-22 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
• Effective Date: 15-Dec-2008
• Referred By: ASTM F2994-18(2022) - Standard Practice for Utilization of Mobile, Automated Cured-In-Place Pipe (CIPP) Impregnation Systems
• Effective Date: 15-Dec-2008
• Referred By: ASTM F1216-22 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
• Effective Date: 15-Dec-2008
• Referred By: ASTM F1743-22 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
• Effective Date: 15-Dec-2008
• Referred By: ASTM F3541-22 - Standard Practice for Sectional Repair of Existing Gravity Flow, Non-Pressure Pipelines and Conduits by Pushed or Pulled-In-Place Installation of Cured-In-Place Thermosetting Resin Pipe (CIPP)
• Effective Date: 15-Dec-2008
• Referred By: ASTM F2599-22 - Standard Practice for Sectional Repair of Damaged Pipe By Means of an Inverted Cured-In-Place Liner<rangeref></rangeref >
• Effective Date: 15-Dec-2008
• Referred By: ASTM F2561-20 - Standard Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One Piece Main and Lateral Cured-in-Place Liner
• Effective Date: 15-Dec-2008

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D5813 −04(Reapproved 2008) An American National Standard
Standard Specification for
1
Cured-In-Place Thermosetting Resin Sewer Piping Systems
This standard is issued under the fixed designation D5813; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D790Test Methods for Flexural Properties of Unreinforced
and Reinforced Plastics and Electrical Insulating Materi-
1.1 This specification covers cured-in-place thermosetting
als
resin pipe (CIPP), 4 through 132-in. (100 through 3353-mm)
D883Terminology Relating to Plastics
equivalent diameter, for use in gravity flow systems for
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
conveying sanitary sewage, storm water, and certain industrial
tics
wastes. This specification is suited for the evaluation and
D1682Test Method for Breaking Load and Elongation of
testing of materials used in the rehabilitation of existing pipes
3
Textile Fabric (Withdrawn 1992)
by the installation and cure of a resin-impregnated fabric liner.
D3039/D3039MTest Method forTensile Properties of Poly-
1.2 This specification can also be extended to cover
mer Matrix Composite Materials
manholes, pump stations, wetwells, vaults, storage tanks, and
D3567PracticeforDeterminingDimensionsof“Fiberglass”
other similar structures where a cured in place liner using
(Glass-Fiber-Reinforced Thermosetting Resin) Pipe and
thermosetting resin is applicable.
Fittings
D3681TestMethodforChemicalResistanceof“Fiberglass”
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a
Deflected Condition
conversions to SI units that are provided for information only
and are not considered standard. D4814Specification for Automotive Spark-Ignition Engine
Fuel
NOTE 1—There are no ISO standards covering the primary subject
F412Terminology Relating to Plastic Piping Systems
matter of this specification.
F1216Practice for Rehabilitation of Existing Pipelines and
1.4 The following safety hazards caveat pertains only to the
Conduits by the Inversion and Curing of a Resin-
test methods portion, Section 8, of this specification: This
Impregnated Tube
standard does not purport to address all of the safety concerns,
F1743Practice for Rehabilitation of Existing Pipelines and
if any, associated with its use. It is the responsibility of the user
ConduitsbyPulled-in-PlaceInstallationofCured-in-Place
of this standard to establish appropriate safety and health
Thermosetting Resin Pipe (CIPP)
practices and determine the applicability of regulatory limita-
F2019Practice for Rehabilitation of Existing Pipelines and
tions prior to use.
Conduits by the Pulled in Place Installation of Glass
Reinforced Plastic (GRP) Cured-in-Place Thermosetting
2. Referenced Documents
Resin Pipe (CIPP)
2
2.1 ASTM Standards:
D543Practices for Evaluating the Resistance of Plastics to
3. Terminology
Chemical Reagents
3.1 General—DefinitionsareinaccordancewithTerminolo-
D638Test Method for Tensile Properties of Plastics
gies D883 and F412. Abbreviations are in accordance with
D695Test Method for Compressive Properties of Rigid
Terminology D1600, unless otherwise indicated.
Plastics
3.2 Definitions of Terms Specific to This Standard:
3.2.1 cured-in-place pipe (CIPP)—hollowcylinderorshape
1
This specification is under the jurisdiction of ASTM Committee D20 on
consistingofafabricwithcured(cross-linked)thermosetresin;
Plastics and is under the direct responsibility of Subcommittee D20.23 on
interior or exterior plastic tube coatings, or both, may be
Reinforced Plastic Piping Systems and Chemical Equipment.
included; this pipe is formed within and takes the shape of an
Current edition approved Dec. 15, 2008. Published February 2009. Originally
approved in 1995. Last previous edition approved in 2004 as D5813–04. DOI:
existing conduit or structure.
10.1520/D5813-04R08.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D5813−04 (2008)
3.2.2 delamination—separation of coating or layers of the 5. Materials and Manufacture
CIPP, or both.
5.1 General—The resins, fabric tube, tube coatings, fil
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D 5813–95 Designation: D 5813 – 04 (Reapproved 2008)
Standard Specification for
Cured-In-Place Thermosetting Resin Sewer PipeCured-In-
1
Place Thermosetting Resin Sewer Piping Systems
This standard is issued under the fixed designation D 5813; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers cured-in-place thermosetting resin pipe (CIPP), 4 through 132-in. (100 through 3353-mm)
equivalent diameter, for use in gravity flow systems for conveying sanitary sewage, storm water, and certain industrial wastes.This
specification is suited for the evaluation and testing of materials used in the rehabilitation of existing pipes by the installation and
cure of a resin-impregnated fabric liner.
1.2The values given in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.2 This specification can also be extended to cover manholes, pump stations, wetwells, vaults, storage tanks, and other similar
structures where a cured in place liner using thermosetting resin is applicable.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
NOTE 1—There are no ISO standards covering the primary subject matter of this specification.
1.3
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 543 Test Method Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D 638 Test Method for Tensile Properties of Plastics
D 695 Test Method for Compressive Properties of Rigid Plastics
D 790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D 883 Terminology Relating to Plastics
D 1600 Terminology for Abbreviated Terms Relating to Plastics
3
D1682 Test Methods of Test for Breaking Load and Elongation of Textile Fabrics
D 3039/D 3039M Test Method forTensile Properties of Fiber-Resin CompositesTest Method forTensile Properties of Polymer
Matrix Composite Materials
D 3567 Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D 3681 Test Method for Chemical Resistance of “Fiberglass” (Glass-Fiber Fiberglass (GlassFiberReinforced Thermosetting-
Resin) Pipe in a Deflected Condition
D 4814 Specification for Automotive Spark—-Ignition Engine Fuel
F 412 Terminology Relating to Plastic Piping Systems
F 1216 Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated
5
Tube Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-ImpregnatedTube
1
This specification is under the jurisdiction of ASTM Committee D-20 on Plastics and is under the direct responsibility of Subcommittee D20.23 on Reinforced Plastic
Piping Systems and Chemical Equipment.
Current edition approved Oct. 10, 1995. Published December 1995.
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is under the direct responsibility of Subcommittee D20.23 on Reinforced Plastic
Piping Systems and Chemical Equipment.
Current edition approved Dec. 15, 2008. Published February 2009. Originally approved in 1995. Last previous edition approved in 2004 as D 5813–04.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 08.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Discontinued; see 1991 Annual Book of ASTM Standards , Vol 07.01.
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D 5813–04 Designation: D 5813 – 04 (Reapproved 2008)
Standard Specification for
1
Cured-In-Place Thermosetting Resin Sewer Piping Systems
This standard is issued under the fixed designation D 5813; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers cured-in-place thermosetting resin pipe (CIPP), 4 through 132-in. (100 through 3353-mm)
equivalent diameter, for use in gravity flow systems for conveying sanitary sewage, storm water, and certain industrial wastes.This
specification is suited for the evaluation and testing of materials used in the rehabilitation of existing pipes by the installation and
cure of a resin-impregnated fabric liner.
1.2 This specification can also be extended to cover manholes, pump stations, wetwells, vaults, storage tanks, and other similar
structures where a cured in place liner using thermosetting resin is applicable.
1.3The values given in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
NOTE 1—There are no ISO standards covering the primary subject matter of this specification.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 543 Test Method Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D 638 Test Method for Tensile Properties of Plastics
D 695 Test Method for Compressive Properties of Rigid Plastics
D 790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D 883 Terminology Relating to Plastics
D 1600 Terminology for Abbreviated Terms Relating to Plastics
3
D1682 Test Methods of Test for Breaking Load and Elongation of Textile Fabrics
D 3039/D 3039M Test Method forTensile Properties of Fiber-Resin CompositesTest Method forTensile Properties of Polymer
Matrix Composite Materials
D 3567 Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D 3681 Test Method for Chemical Resistance of “Fiberglass” (Glass-Fiber Fiberglass (GlassFiberReinforced Thermosetting-
Resin) Pipe in a Deflected Condition
D 4814 Specification for Automotive Spark—-Ignition Engine Fuel
F 412 Terminology Relating to Plastic Piping Systems
F 1216 Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-ImpregnatedTube
F 1743 PracticeforRehabilitationofExisitingExistingPipelinesandConduitsbyPulled-in-PlaceInstallationofCured-in-Place
Thermosetting Resin Pipe (CIPP)
F 2019 PracticeforRehabilitationofExisitingExistingPipelinesandConduitsbyPulled-in-PlacethePulledinPlaceInstallation
of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is under the direct responsibility of Subcommittee D20.23 on Reinforced Plastic
Piping Systems and Chemical Equipment.
Current edition approved Mar. 1, 2004. Published March 2004.
Originally approved in 1995. Last previous edition approved in 1995 as D5813–95.
Current edition approved Dec. 15, 2008. Published February 2009. Originally approved in 1995. Last previous edition approved in 2004 as D 5813–04.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------
...