ASTM B349/B349M-09
(Specification)Standard Specification for Zirconium Sponge and Other Forms of Virgin Metal for Nuclear Application
Standard Specification for Zirconium Sponge and Other Forms of Virgin Metal for Nuclear Application
ABSTRACT
This specification covers one grade of virgin zirconium metal commonly designated as sponge because of its porous, sponge-like texture, but it may also take other forms such as chunklets. The one grade described is designated as Reactor Grade R60001, suitable for use in nuclear applications. The main characteristic of the reactor grade is its low nuclear cross section as achieved by removal of hafnium. Zirconium metal is usually prepared by reduction of zirconium tetrachloride, and gets its physical characteristics from the processes involved in production. These characteristics may be expected to vary greatly with manufacturing methods. Only virgin zirconium metal, in identified, uniform, well-mixed blends, shall be used. The zirconium metal shall conform to the requirements for chemical composition specified.
SCOPE
1.1 This specification covers one grade of virgin zirconium metal commonly designated as sponge because of its porous, sponge-like texture, but it may also take other forms such as chunklets, suitable for use in nuclear applications.
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B349/B349M −09
StandardSpecification for
Zirconium Sponge and Other Forms of Virgin Metal for
1
Nuclear Application
This standard is issued under the fixed designation B349/B349M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2 Lot Definition—a lot shall consist of a single blend
produced at one time.
1.1 This specification covers one grade of virgin zirconium
metal commonly designated as sponge because of its porous,
4. Classification
sponge-like texture, but it may also take other forms such as
chunklets, suitable for use in nuclear applications.
4.1 Primary zirconium is furnished in one grade designated
as Reactor Grade R60001, suitable for nuclear applications.
1.2 Unless a single unit is used, for example corrosion mass
2
The main characteristic of the reactor grade is its low neutron
gain in mg/dm , the values stated in either inch-pound or SI
capture cross section as achieved by removal of hafnium. The
units are to be regarded separately as standard. The values
manufacturer must use procedures to prevent contamination
stated in each system are not exact equivalents; therefore each
with other high cross-section materials.
system must be used independently of the other. SI values
cannot be mixed with inch-pound values.
5. Ordering Information
1.3 This standard does not purport to address all of the
5.1 Purchase orders for material under this specification
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- shallincludethefollowinginformation,asrequired,todescribe
adequately the desired material:
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
5.1.1 Quantity (weight),
5.1.2 Name of material (zirconium sponge or chunklets),
2. Referenced Documents
5.1.3 Grade designation (see 4.1),
2
2.1 ASTM Standards:
5.1.4 ASTM designation and year of issue.
E29 Practice for Using Significant Digits in Test Data to
5.2 In addition to the data specified in 5.1, the following
Determine Conformance with Specifications
options and points of agreement between the manufacturer and
the purchaser shall be specified in the purchase order, as
3. Terminology
required.
3.1 Forms:
5.2.1 Sampling and duplicate samples (see 8.1 and 8.2).
3.1.1 chunklets, n—zirconium metal produced from the
5.2.2 Certification reports (Section 14), and
reduction of the chloride, usually by sodium.
5.2.3 Packaging (Section 16).
3.1.1.1 Discussion—In this process, the reduced metal is
melted and dripped onto a rotating disk to form chunklets.
NOTE1—Atypicalorderingdescriptionisasfollows:5000lb(2000kg)
reactor grade zirconium, Grade R60001, ASTM Specification B349/
3.1.2 sponge, n—zirconium metal produced from the reduc-
B349M - 09.
tion of the chloride, usually by magnesium.
3.1.2.1 Discussion—The process is one where the metal
6. Materials and Manufacture
condenses to the solid state and does not melt.
6.1 Zirconium metal is usually prepared by reduction of
zirconium tetrachloride, and gets its physical characteristics
1
This specification is under the jurisdiction of ASTM Committee B10 on
from the processes involved in production. These characteris-
Reactive and Refractory Metals and Alloysand is the direct responsibility of
Subcommittee B10.02 on Zirconium and Hafnium.
tics may be expected to vary greatly with manufacturing
Current edition approved April 15, 2009. Published June 2009. Originally
methods.This specification, however, is not limited to material
approved in 1960. Last previous edition approved in 2003 as B349/B349M – 03.
prepared by reduction of tetrachloride or to material of any
DOI: 10.1520/B0349_B0349M-09.
2
specific physical form.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.2 Only virgin zirconium metal, in identified, uniform,
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. well-mixed blends, shall be supplied under this specification.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B349/B349M−09
7. Chemical Composition 9.1.1.2 Samples for chemical tests shall be taken from solid
metal below the surface porosity of the as-cast ingot. The
7.1 The zirconium metal supplied under this specification
samples shall be taken from a minimum of three places equally
shall conform to the requirements for chemical compo
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B349/B349M–03 Designation: B 349/B 349M – 09
Standard Specification for
Zirconium Sponge and Other Forms of Virgin Metal for
1
Nuclear Application
This standard is issued under the fixed designation B 349/B 349M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1This specification covers one grade of virgin zirconium metal commonly designated as sponge because of its porous,
sponge-like texture, but it may also take other forms such as chunklets.
1.2The one grade described is designated as Reactor Grade R60001, suitable for use in nuclear applications. The main
characteristic of the reactor grade is its low nuclear cross section as achieved by removal of hafnium. The manufacturer must use
procedures to prevent contamination with other high cross-section materials.
1.3Unless a single unit is used, for example corrosion mass gain in mg/dm
1.1 This specification covers one grade of virgin zirconium metal commonly designated as sponge because of its porous,
sponge-like texture, but it may also take other forms such as chunklets, suitable for use in nuclear applications.
2
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm , the values stated in either inch-pound or SI units
are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must
be used independently of the other. SI values cannot be mixed with inch-pound values.
1.4
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
3. Terminology
3.1 Lot Definitions: Forms:
3.1.1 castings—a lot shall consist of all castings produced from the same pour. chunklets, n—zirconium metal produced from
the reduction of the chloride, usually by sodium.
3.1.1.1 Discussion—In this process, the reduced metal is melted and dripped onto a rotating disk to form chunklets.
3.1.2 ingot—no definition required.
3.1.3rounds, flats, tubes, and wrought powder metallurgical products (single definition, common to nuclear and non-nuclear
standards)—a lot shall consist of a material of the same size, shape, condition, and finish produced from the same ingot or powder
blend by the same reduction schedule and the same heat treatment parameters. Unless otherwise agreed between manufacturer and
purchaser, a lot shall be limited to the product of an 8 h period for final continuous anneal, or to a single furnace load for final
batch anneal.
3.1.4sponge—a lot shall consist of a single blend produced at one time.
3.1.5weld fittings—definition is to be mutually agreed upon between manufacturer and the purchaser. sponge, n—zirconium
metal produced from the reduction of the chloride, usually by magnesium.
3.1.2.1 Discussion—The process is one where the metal condenses to the solid state and does not melt.
3.2 Lot Definition—a lot shall consist of a single blend produced at one time.
1
This specification is under the jurisdiction of ASTM Committee B10 on Reactive and Refractory Metals and Alloys and is the direct responsibility of Subcommittee
B10.02 on Zirconium and Hafnium.
Current edition approved May 10, 2003. Published May 2003. Originally approved in 1960. Last previous edition approved in 2001 as B349–01.
Current edition approved April 15, 2009. Published June 2009. Originally approved in 1960. Last previous edition approved in 2003 as B 349/B 349M – 03.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 14.02.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B 349/B 349M – 09
4. Classification
4.1 Primary zirconium is furnished in one grade designated as Reactor Grade R60001, suitable for nuclear applications. The
main characterist
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.