ASTM A965/A965M-12
(Specification)Standard Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts
Standard Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts
ABSTRACT
This specification covers austenitic stainless steel forgings for pressure and high temperature parts such as boilers, pressure vessels, and associated equipment. The grades covered here are F304, F304H, F304L, F304N, F304LN, F309H, F310, F310H, F316, F316H, F316L, F316N, F316LN, F321, F321H, F347, F347H, F348, F348H, FXM-19, FXM-11, and F46. Materials shall be produced by melting, forging, and rough machining, and shall be furnished by heat treatment in solution treated condition (solution annealing and quenching in water, oil, or a polymer water solution). Stainless steel specimens shall undergo heat and product analyses to evaluate the conformance of individual grades to specified elemental chemical compositions. Forgings shall also be examined for the adherence of each grade to required grain sizes and mechanical properties, which include tensile strength, yield strength, elongation, and reduction of area.
SCOPE
1.1 This specification covers austenitic stainless steel forgings for boilers, pressure vessels, high temperature parts, and associated equipment.
1.2 Supplementary requirements are provided for use when additional testing, inspection, or processing is required. In addition, supplementary requirements from Specification A788/A788M may be specified when appropriate.
1.3 This specification includes the austenitic steel forgings that were a part of Specification A336/A336M.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A965/A965M −12
StandardSpecification for
Steel Forgings, Austenitic, for Pressure and High
1
Temperature Parts
This standard is issued under the fixed designationA965/A965M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* A745/A745M Practice for Ultrasonic Examination of Aus-
tenitic Steel Forgings
1.1 This specification covers austenitic stainless steel forg-
A788/A788M Specification for Steel Forgings, General Re-
ings for boilers, pressure vessels, high temperature parts, and
quirements
associated equipment.
E112 Test Methods for Determining Average Grain Size
1.2 Supplementary requirements are provided for use when
2.2 Other Standards:
additional testing, inspection, or processing is required. In
ASME Boiler and Pressure Vessel Code, including Section
addition, supplementary requirements from Specification
VIII Pressure Vessels and Section IX Welding Qualifica-
A788/A788M may be specified when appropriate.
3
tions
1.3 This specification includes the austenitic steel forgings
that were a part of Specification A336/A336M.
3. Ordering Information and General Requirements
1.4 The values stated in either SI units or inch-pound units
3.1 In addition to the ordering information required by
are to be regarded separately as standard. The values stated in
Specification A788/A788M, the intended use should be stated
each system may not be exact equivalents; therefore, each
if 5.1 is to be applicable.
system shall be used independently of the other. Combining
3.2 Material supplied to this specification shall conform to
values from the two systems may result in non-conformance
the requirements of Specification A788/A788M, which out-
with the standard.
lines additional ordering information, manufacturing
1.5 Unless the order specifies the applicable “M” specifica-
requirements, testing and retesting methods and procedures,
tion designation, the material shall be furnished to the inch-
marking, certification, product analysis variations, and addi-
pound units.
tional supplementary requirements.
1.6 This standard does not purport to address all of the
3.3 If the requirements of this specification are in conflict
safety concerns, if any, associated with its use. It is the
with the requirements of Specification A788/A788M, the
responsibility of the user of this standard to establish appro-
requirements of this specification shall prevail.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
3.4 If the forgings are intended for use under the ASME
Boiler and Pressure Vessel Code at temperatures exceeding
2. Referenced Documents
1000°F [540°C], then use Supplementary Requirement S7.
2
2.1 ASTM Standards: Grain size requirements for service exceeding 1000°F [540°C]
A336/A336M Specification for Alloy Steel Forgings for should be specified unless the required grade has the suffix
Pressure and High-Temperature Parts “H.”
A370 Test Methods and Definitions for Mechanical Testing
of Steel Products
4. Melting and Forging
4.1 In addition to the melting and forging requirements of
1 Specification A788/A788M, which may include Supplemen-
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee tary Requirement S8, the following condition applies:
A01.06 on Steel Forgings and Billets.
4.1.1 A sufficient discard shall be made to secure freedom
Current edition approved March 1, 2012. Published April 2012. Originally
from injurious pipe and undue segregation.
approved in 1996. Last previous edition approved in 2010 as A965/A965M – 10.
DOI: 10.1520/A0965_A0965M-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from American Society of Mechanical Engineers (ASME), ASME
the ASTM website. International Headquarters, Three Park Ave., New York, NY 10016-5990.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A965/A965M−12
5. Machining 8. Mechanical Properties
5.1 Forged pressure vessels for steam power service shall 8.1 Requirements—The material shall conform to the re-
have the inner surface machined or ground. Unfired pressure quirements for mechanical properties prescribed in Table 2 or,
vessels shall
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A965/A965M–10 Designation: A965/A965M – 12
Standard Specification for
Steel Forgings, Austenitic, for Pressure and High
1
Temperature Parts
This standard is issued under the fixed designationA965/A965M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers austenitic stainless steel forgings for boilers, pressure vessels, high temperature parts, and
associated equipment.
1.2 Supplementary requirements are provided for use when additional testing, inspection, or processing is required. In addition,
supplementary requirements from Specification A788/A788M may be specified when appropriate.
1.3 This specification includes the austenitic steel forgings that were a part of Specification A336/A336M.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound
units.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A336/A336M Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A745/A745M Practice for Ultrasonic Examination of Austenitic Steel Forgings
A788/A788M Specification for Steel Forgings, General Requirements
E112 Test Methods for Determining Average Grain Size
2.2 Other Standards:
3
ASME Boiler and Pressure Vessel Code, including Section VIII Pressure Vessels and Section IX Welding Qualifications
3. Ordering Information and General Requirements
3.1 In addition to the ordering information required by Specification A788/A788M, the intended use should be stated if 5.1 is
to be applicable.
3.2 Material supplied to this specification shall conform to the requirements of Specification A788/A788M, which outlines
additional ordering information, manufacturing requirements, testing and retesting methods and procedures, marking, certification,
product analysis variations, and additional supplementary requirements.
3.3 IftherequirementsofthisspecificationareinconflictwiththerequirementsofSpecificationA788/A788M,therequirements
of this specification shall prevail.
3.4 If the forgings are intended for use under the ASME Boiler and Pressure Vessel Code at temperatures exceeding 1000°F
[540°C], then use Supplementary Requirement S7. Grain size requirements for service exceeding 1000°F [540°C] should be
specified unless the required grade has the suffix “H.”
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.06
on Steel Forgings and Billets.
Current edition approved Nov.March 1, 2010.2012. Published December 2010.April 2012. Originally approved in 1996. Last previous edition approved in 20062010 as
A965/A965M–06a.A965/A965M – 10. DOI: 10.1520/A0965_A0965M-102.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A965/A965M – 12
4. Melting and Forging
4.1 In addition to the melting and forging requirements of Specification A788/A788M, which may include Supplementary
Requirement S8, the following condition applies:
4.1.1 A sufficient discard shall be made to secure freedom from injurious pipe a
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A965/A965M–10 Designation: A965/A965M – 12
Standard Specification for
Steel Forgings, Austenitic, for Pressure and High
1
Temperature Parts
This standard is issued under the fixed designationA965/A965M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers austenitic stainless steel forgings for boilers, pressure vessels, high temperature parts, and
associated equipment.
1.2 Supplementary requirements are provided for use when additional testing, inspection, or processing is required. In addition,
supplementary requirements from Specification A788/A788M may be specified when appropriate.
1.3 This specification includes the austenitic steel forgings that were a part of Specification A336/A336M.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound
units.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A336/A336M Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A745/A745M Practice for Ultrasonic Examination of Austenitic Steel Forgings
A788/A788M Specification for Steel Forgings, General Requirements
E112 Test Methods for Determining Average Grain Size
2.2 Other Standards:
3
ASME Boiler and Pressure Vessel Code, including Section VIII Pressure Vessels and Section IX Welding Qualifications
3. Ordering Information and General Requirements
3.1 In addition to the ordering information required by Specification A788/A788M, the intended use should be stated if 5.1 is
to be applicable.
3.2 Material supplied to this specification shall conform to the requirements of Specification A788/A788M, which outlines
additional ordering information, manufacturing requirements, testing and retesting methods and procedures, marking, certification,
product analysis variations, and additional supplementary requirements.
3.3 IftherequirementsofthisspecificationareinconflictwiththerequirementsofSpecificationA788/A788M,therequirements
of this specification shall prevail.
3.4 If the forgings are intended for use under the ASME Boiler and Pressure Vessel Code at temperatures exceeding 1000°F
[540°C], then use Supplementary Requirement S7. Grain size requirements for service exceeding 1000°F [540°C] should be
specified unless the required grade has the suffix “H.”
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.06
on Steel Forgings and Billets.
Current edition approved Nov.March 1, 2010.2012. Published December 2010.April 2012. Originally approved in 1996. Last previous edition approved in 20062010 as
A965/A965M–06a.A965/A965M – 10. DOI: 10.1520/A0965_A0965M-102.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A965/A965M – 12
4. Melting and Forging
4.1 In addition to the melting and forging requirements of Specification A788/A788M, which may include Supplementary
Requirement S8, the following condition applies:
4.1.1 A sufficient discard shall be made to secure freedom from injurious pipe a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.