ASTM A484/A484M-24
(Specification)Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings
Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings
ABSTRACT
This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished materials, except wire, for forging. The materials shall be furnished in one of the following conditions: (1) hot-worked; (2) hot-worked and annealed; (3) hot-worked, annealed and cold-worked; or (4) hot-worked, annealed, and heat-treated. Product analysis tolerances shall be performed wherein the specimens shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, molybdenum, titanium, cobalt, columbium, tantalum, copper, aluminum, nitrogen, tungsten, vanadium, and selenium. The materials shall be heat treated and austenitic stainless steels and austenitic-ferritic grades shall be furnished in the solution annealed condition and shall conform to the required values of temperature, permitted annealing procedure, quenching, and rapid cooling.
SCOPE
1.1 This specification2 covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire) for forging, under each of the following specifications issued by ASTM: Specifications A276/A276M, A314, A458, A477, A479/A479M, A564/A564M, A565/A565M, A582/A582M, A638/A638M, A705/A705M, and A831/A831M.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.
1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1.
1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A480/A480M.
1.5 General requirements for wire products in coils are covered in Specification A555/A555M.
1.6 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: A484/A484M − 24
Standard Specification for
General Requirements for Stainless Steel Bars, Billets,
1
Shapes, and Forgings
This standard is issued under the fixed designation A484/A484M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* The values stated in each system may not be exact equivalents;
2 therefore, each system shall be used independently of the other.
1.1 This specification covers general requirements that
Combining values from the two systems may result in noncon-
shall apply to wrought stainless steel bars, shapes, forgings,
formance with the standard.
and billets or other semi-finished material (except wire) for
1.7 This international standard was developed in accor-
forging, under each of the following specifications issued by
dance with internationally recognized principles on standard-
ASTM: Specifications A276/A276M, A314, A458, A477,
ization established in the Decision on Principles for the
A479/A479M, A564/A564M, A565/A565M, A582/A582M,
Development of International Standards, Guides and Recom-
A638/A638M, A705/A705M, and A831/A831M.
mendations issued by the World Trade Organization Technical
1.2 In the case of conflict between a requirement of a
Barriers to Trade (TBT) Committee.
product specification and a requirement of this specification,
the product specification shall prevail. In the case of conflict
2. Referenced Documents
between a requirement of the product specification or a
3
2.1 ASTM Standards:
requirement of this specification and a more stringent require-
A6/A6M Specification for General Requirements for Rolled
ment of the purchase order, the purchase order shall prevail.
Structural Steel Bars, Plates, Shapes, and Sheet Piling
The purchase order requirements shall not take precedence if
A262 Practices for Detecting Susceptibility to Intergranular
they, in any way, violate the requirements of the product
Attack in Austenitic Stainless Steels
specification or this specification; for example, by waiving a
A276/A276M Specification for Stainless Steel Bars and
test requirement or by making a test requirement less stringent.
Shapes
1.3 The requirements for introduction of new materials in
A314 Specification for Stainless Steel Billets and Bars for
specifications referencing this specification are given in Annex
Forging
A1.
A370 Test Methods and Definitions for Mechanical Testing
of Steel Products
1.4 General requirements for flat-rolled stainless steel prod-
A458 Specification for Hot-Worked, Hot-Cold-Worked, and
ucts other than bar are covered in Specification A480/A480M.
Cold-Worked Alloy Steel Bars for High Strength at
1.5 General requirements for wire products in coils are
4
Elevated Temperatures (Withdrawn 1988)
covered in Specification A555/A555M.
A477 Specification for Hot-Worked, Hot-Cold Worked and
1.6 This specification is expressed in both inch-pound units
Cold-Worked Alloy Steel Forgings and Forging Billets for
and in SI units; however, unless the purchase order or contract
High Strength at Elevated Temperatures (Withdrawn
4
specifies the applicable M specification designation (SI units),
1988)
the inch-pound units shall apply. The values stated in either
A479/A479M Specification for Stainless Steel Bars and
inch-pound units or SI units are to be regarded separately as
Shapes for Use in Boilers and Other Pressure Vessels
standard. Within the text, the SI units are shown in brackets.
A480/A480M Specification for General Requirements for
Flat-Rolled Stainless and Heat-Resisting Steel Plate,
Sheet, and Strip
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
3
A01.17 on Flat-Rolled and Wrought Stainless Steel. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Jan. 1, 2024. Published January 2024. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1963. Last previous edition approved in 2023 as A484/A484M – 23a. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A0484_A0484M-24. the ASTM website.
2 4
For ASME Boiler and Pressure Vessel Code Applications, see related Specifi- The last approved version of this historical standard is referenced on
cation SA-484/SA-484M in Section II of that code
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A484/A484M − 23a A484/A484M − 24
Standard Specification for
General Requirements for Stainless Steel Bars, Billets,
1
Shapes, and Forgings
This standard is issued under the fixed designation A484/A484M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets
or other semi-finished material (except wire) for forging, under each of the following specifications issued by ASTM:
Specifications A276/A276M, A314, A458, A477, A479/A479M, A564/A564M, A565/A565M, A582/A582M, A638/A638M,
A705/A705M, and A831/A831M.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product
specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this
specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order
requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this
specification; for example, by waiving a test requirement or by making a test requirement less stringent.
1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1.
1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A480/A480M.
1.5 General requirements for wire products in coils are covered in Specification A555/A555M.
1.6 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract
specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either
inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The
values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
Combining values from the two systems may result in nonconformance with the standard.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Sept. 1, 2023Jan. 1, 2024. Published September 2023January 2024. Originally approved in 1963. Last previous edition approved in 2023 as
A484/A484M – 23.A484/A484M – 23a. DOI: 10.1520/A0484_A0484M-23A.10.1520/A0484_A0484M-24.
2
For ASME Boiler and Pressure Vessel Code Applications, see related Specification SA-484/SA-484M in Section II of that code.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A484/A484M − 24
2. Referenced Documents
3
2.1 ASTM Standards:
A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A276/A276M Specification for Stainless Steel Bars and Shapes
A314 Specification for Stainless Steel Billets and Bars for Forging
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A458 Specification for Hot-Worked, Hot-Cold-Worked, and Cold-Worked Alloy Steel Bars for High Strength at Elevated
4
Temperatures (Withdrawn 1988)
A477 Specification for Hot-Worked, Hot-Cold Worked and Cold-Worked Alloy Steel Forgings and Forging Billets for High
4
Strength at Elevated Temperatures (Withdrawn 1988)
A479/A479M Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressur
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.