ASTM F1062-97(2013)
(Test Method)Standard Test Method for Verification of Ski Binding Test Devices
Standard Test Method for Verification of Ski Binding Test Devices
SIGNIFICANCE AND USE
4.1 Results obtained by this test method can be used to determine the suitability of specific test device designs in measuring the release moments of ski/boot/binding systems.
4.2 This test method provides a means by which manufacturers of test devices and manufacturers of releasable ski bindings can provide compatible instructions to facilities which perform the final inspection of the complete boot/binding/ski system prior to use.
4.3 This test method is not appropriate for determining precision between operators.
SCOPE
1.1 This test method defines procedures to determine agreement between a standard apparatus for measuring the release moments of ski bindings and a test device of unspecified design.
1.2 This test method also covers procedures for checking agreement between individual devices of identical but unspecified design, intended for determining the release moments of ski bindings.
1.3 Values expressed in newton meters, newtons, and centimeters are to be regarded as the standard.
1.4 Values expressed in units of torque may be converted to the appropriate force values when devices which indicate force are used.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1062 −97 (Reapproved 2013)
Standard Test Method for
Verification of Ski Binding Test Devices
This standard is issued under the fixed designation F1062; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F1064 Practice for Sampling and Inspection of Complete
and Incomplete Alpine Ski/Binding/Boot Systems in
1.1 This test method defines procedures to determine agree-
Rental Applications
ment between a standard apparatus for measuring the release
moments of ski bindings and a test device of unspecified
3. Terminology
design.
3.1 Definitions—The terms and abbreviations used in this
1.2 This test method also covers procedures for checking
document are defined in accordance with Test Method F504,
agreement between individual devices of identical but unspeci-
Specification F1061, Terminology E456, Practices E4, and
fied design, intended for determining the release moments of
Practice E74.
ski bindings.
3.2 Definitions of Terms Specific to This Standard:
1.3 Values expressed in newton meters, newtons, and cen-
3.2.1 a—difference between the calibration of the specific
timeters are to be regarded as the standard.
device tested for agreement with an instrument of the type
1.4 Values expressed in units of torque may be converted to
described in Test Method F504 and the calibration of an
the appropriate force values when devices which indicate force
individual device of the same design.
are used.
3.2.2 d—agreementbetweenthetestdeviceandthestandard
1.5 This standard does not purport to address all of the
apparatus described in Test Method F504 and Section 9 of this
safety concerns, if any, associated with its use. It is the
test method.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica- 3.2.3 r—imprecision of the device tested.
bility of regulatory limitations prior to use.
3.2.4 operating range (OR)—the portion of the full range of
the device which may be employed in accordance with
2. Referenced Documents
Practices F1063 and F1064. OR shall be defined by the user in
2.1 ASTM Standards:
accordance with the Inspection section ofAnnex 2 of Practices
E4 Practices for Force Verification of Testing Machines
F1063 and F1064.
E29 Practice for Using Significant Digits in Test Data to
3.2.5 recommended operating range (ROR)—the portion of
Determine Conformance with Specifications
the full range of the test device that is in accordance with
E74 Practice of Calibration of Force-Measuring Instruments
Proposed Specification P 193.
for Verifying the Force Indication of Testing Machines
E456 Terminology Relating to Quality and Statistics 3.2.6 reference binding—a binding or group of bindings
F504 Test Method for Measuring the Quasi-Static Release
used in the verification of a test device.
Moments of Alpine Ski Bindings
3.2.7 standard apparatus—laboratory equipment including
F1061 Specification for Ski Binding Test Devices
a test frame and instrumentation used as the basis for compari-
F1063 Practice for Functional Inspections and Adjustments
son with the test device.
of Alpine Ski/Binding/Boot Systems
3.2.8 test device—a machine for determining the release
moments of ski/boot/binding systems.
This test method is under the jurisdiction of ASTM Committee F27 on Snow
3.3 Symbols:
Skiing and is the direct responsibility of Subcommittee F27.10 on Binding Test
Procedures.
3.3.1 M — a moment in a horizontal plane as shown in the
z
Current edition approved July 1, 2013. Published August 2013. Originally
figure in Test Method F504, which illustrates terminology
approved in 1988. Last previous edition approved in 2008 as F1062 – 97 (2008).
relating to the boot/ski system.
DOI: 10.1520/F1062-97R13.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.3.2 M — a moment in a vertical plane with the ski as
y
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
shown in the figure in Test Method F504, which illustrates
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. terminology relating to the boot/ski system.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1062−97 (2013)
4. Significance and Use temperature over the course of the test by more than 2°C and
humidity by more than 5 %.
4.1 Results obtained by this test method can be used to
determine the suitability of specific test device designs in
8. Procedure
measuring the release moments of ski/boot/binding systems.
8.1 Perform five repetitions of the following procedure:
4.2 This test method provides a means by which manufac-
8.1.1 Using the standard apparatus, perform three repeti-
turers of test devices and manufacturers of releasable ski
tionsofatestrequiredforTypeI,II,orIIIdevices,andperform
bindingscanprovidecompatibleinstructionstofacilitieswhich
three repetitions of the analogous test on the test device.
perform the final inspection of the complete boot/binding/ski
8.1.1.1 Randomly select which series of three tests will be
system prior to use.
conducted first.
4.3 This test method is not appropriate for determining
8.1.1.2 From the Table on LoadApplication of Test Method
precision between operators.
F504, use tests 1.1 and 1.2 for Type I devices, tests 2.1 and 2.2
(if appropriate) forType II devices and tests as specified by the
5. Apparatus
test device manufacturer for Type III devices.
5.1 Test Ski—Thetestskishallmeetthestiffskidefinitionin
8.1.1.3 Follow the test device manufacturer’s instructions
the portion of the Apparatus Section of Test Method F504
for conducting analogous tests.
pertaining to skis and bindings.
8.2 Perform the procedure in 8.1-8.1.1.3 at the beginning,
5.2 Test Sole—The test sole shall meet the requirements in
middle, and end of the ROR. If the reference binding cannot be
the portion of the Apparatus Section of Test Method F504
adjusted for release over the full ROR, perform the test(s) at 10
pertaining to boots, and shall be of a design compatible with
or 90 % of the limit(s) of the reference binding as appropriate.
the reference binding. The test sole may be modified to
8.2.1 Immediately before and after each cycle of
establish necessary interfaces with the standard apparatus and
8.1-8.1.1.3, measure and record t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.