ASTM A370-07a
(Test Method)Standard Test Methods and Definitions for Mechanical Testing of Steel Products
Standard Test Methods and Definitions for Mechanical Testing of Steel Products
SCOPE
1.1 These test methods cover procedures and definitions for the mechanical testing of wrought and cast steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.
1.2 The following mechanical tests are described:
1.4 The values stated in inch-pound units are to be regarded as the standard.
1.5 When this document is referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 or 8 in. may be reported in SI unit gauge lengths of 50 or 200 mm, respectively, as applicable. Conversely, when this document is referenced in an inch-pound product specification, the yield and tensile values may be determined in SI units then converted into inch-pound units. The elongation determined in SI unit gauge lengths of 50 or 200 mm may be reported in inch-pound gauge lengths of 2 or 8 in., respectively, as applicable.
1.6 Attention is directed to Practices A 880 and E 1595 when there may be a need for information on criteria for evaluation of testing laboratories.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 370 – 07a
Standard Test Methods and Definitions for
1
Mechanical Testing of Steel Products
This standard is issued under the fixed designation A 370; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* inch-pound (ksi) units then converted into SI (MPa) units. The
2 elongation determined in inch-pound gauge lengths of 2 or 8
1.1 These test methods cover procedures and definitions
in. may be reported in SI unit gauge lengths of 50 or 200 mm,
for the mechanical testing of wrought and cast steels, stainless
respectively, as applicable. Conversely, when this document is
steels, and related alloys. The various mechanical tests herein
referenced in an inch-pound product specification, the yield
described are used to determine properties required in the
and tensile values may be determined in SI units then con-
product specifications. Variations in testing methods are to be
verted into inch-pound units. The elongation determined in SI
avoided, and standard methods of testing are to be followed to
unit gauge lengths of 50 or 200 mm may be reported in
obtain reproducible and comparable results. In those cases in
inch-pound gauge lengths of 2 or 8 in., respectively, as
which the testing requirements for certain products are unique
applicable.
or at variance with these general procedures, the product
1.6 Attention is directed to Practices A 880 and E 1595
specification testing requirements shall control.
when there may be a need for information on criteria for
1.2 The following mechanical tests are described:
evaluation of testing laboratories.
Sections
1.7 This standard does not purport to address all of the
Tension 5 to 13
Bend 14
safety concerns, if any, associated with its use. It is the
Hardness 15
responsibility of the user of this standard to establish appro-
Brinell 16
priate safety and health practices and determine the applica-
Rockwell 17
Portable 18
bility of regulatory limitations prior to use.
Impact 19 to 28
Keywords 29
2. Referenced Documents
3
1.3 Annexes covering details peculiar to certain products
2.1 ASTM Standards:
are appended to these test methods as follows:
A 703/A 703M Specification for Steel Castings, General
Annex
Requirements, for Pressure-Containing Parts
Bar Products A1.1
A 781/A 781M Specification for Castings, Steel and Alloy,
Tubular Products Annex A2
Fasteners Annex A3 Common Requirements, for General Industrial Use
Round Wire Products Annex A4
A 833 Practice for Indentation Hardness of Metallic Mate-
Significance of Notched-Bar Impact Testing Annex A5
rials by Comparison Hardness Testers
Converting Percentage Elongation of Round Specimens to Annex A6
Equivalents for Flat Specimens A 880 Practice for Criteria for Use in Evaluation of Testing
Testing Multi-Wire Strand Annex A7
Laboratories and Organizations for Examination and In-
Rounding of Test Data Annex A8
4
spection of Steel, Stainless Steel, and Related Alloys
Methods for Testing Steel Reinforcing Bars Annex A9
Procedure for Use and Control of Heat-Cycle Simulation Annex A10 E4 Practices for Force Verification of Testing Machines
E6 Terminology Relating to Methods of Mechanical Test-
1.4 The values stated in inch-pound units are to be regarded
ing
as the standard.
E8 Test Methods for Tension Testing of Metallic Materials
1.5 When this document is referenced in a metric product
E8M Test Methods for Tension Testing of Metallic Mate-
specification,theyieldandtensilevaluesmaybedeterminedin
rials [Metric]
E10 Test Method for Brinell Hardness of Metallic Materi-
1
als
These test methods and definitions are under the jurisdiction of ASTM
Committee A01 on Steel, Stainless Steel and Related Alloys and are the direct
responsibility of Subcommittee A01.13 on Mechanical and Chemical Testing and
Processing Methods of Steel Products and Processes.
3
Current edition approved June 1, 2007. Published June 2007. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 1953. Last previous edition approved in 2007 as A 370 – 07. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cation SA-370 in Section II of that Code. the ASTM website.
4
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A370–07 Designation: A 370 – 07a
Standard Test Methods and Definitions for
1
Mechanical Testing of Steel Products
This standard is issued under the fixed designation A 370; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 These test methods cover procedures and definitions for the mechanical testing of wrought and cast steels, stainless steels,
and related alloys. The various mechanical tests herein described are used to determine properties required in the product
specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain
reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance
with these general procedures, the product specification testing requirements shall control.
1.2 The following mechanical tests are described:
Sections
Tension 5to13
Bend 14
Hardness 15
Brinell 16
Rockwell 17
Portable 18
Impact 19 to 28
Keywords 29
1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows:
Annex
Bar Products A1.1
Tubular Products Annex A2
Fasteners Annex A3
Round Wire Products Annex A4
Significance of Notched-Bar Impact Testing Annex A5
Converting Percentage Elongation of Round Specimens to Annex A6
Equivalents for Flat Specimens
Testing Multi-Wire Strand Annex A7
Rounding of Test Data Annex A8
Methods for Testing Steel Reinforcing Bars Annex A9
Procedure for Use and Control of Heat-Cycle Simulation Annex A10
1.4 The values stated in inch-pound units are to be regarded as the standard.
1.5 When this document is referenced in a metric product specification, the yield and tensile values may be determined in
inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 or 8 in.
may be reported in SI unit gauge lengths of 50 or 200 mm, respectively, as applicable. Conversely, when this document is
referenced in an inch-pound product specification, the yield and tensile values may be determined in SI units then converted into
inch-pound units. The elongation determined in SI unit gauge lengths of 50 or 200 mm may be reported in inch-pound gauge
lengths of 2 or 8 in., respectively, as applicable.
1.6 Attention is directed to PracticesA 880 and E 1595 when there may be a need for information on criteria for evaluation of
testing laboratories.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1
These test methods and definitions are under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and are the direct responsibility of
Subcommittee A01.13 on Mechanical and Chemical Testing and Processing Methods of Steel Products and Processes.
Current edition approvedAprilJune 1, 2007. PublishedAprilJune 2007. Originally approved in 1953. Last previous edition approved in 20062007 asA370–06.A 370 – 07.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-370 in Section II of that Code.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A 370 – 07a
2. Referenced Documents
3
2.1 ASTM Standards:
A 703/A 703M Specification for Steel Castings, General Requirements, for Pressure-Containing Parts
A 781/A 781M Specification for Castings, Steel and Alloy, Common Requirements, for General Industrial Use
A 833 Practice for Indentation Hardness of Metallic Materials by Comparison Hardness Testers
A 880 Practice for Criteria for Use in Evaluation of Testing Laboratories and Organizations for Examination and Inspection of
Steel, Stainless Steel, and Related Alloys
E4 Practices for Force Verification of Testing Machines
E6 Terminology Relating to Methods of Mechanical Testing
E8 Test Methods for Tension Testing of Metallic Materials
E8M Test Meth
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.