Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 1: Bituminous emulsions

This European Standard specifies a method for the determination of the efflux time at 40 °C of bituminous emulsions in seconds using an efflux viscometer. Alternative test temperature is 50 °C.
NOTE   The procedure described in this standard may also be followed to determine efflux time at other temperatures such as for instance 25 °C.
WARNING - The use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels Ausflussviskosimeter - Teil 1: Bitumenemulsionen

Diese Europäische Norm legt ein Verfahren zur Bestimmung der Ausflusszeit in Sekunden von Bitumenemul-sionen bei 40 °C unter Anwendung eines Ausflussviskosimeters fest. Die alternative Prüftemperatur beträgt 50 °C.
ANMERKUNG Die in dieser Norm beschriebene Durchführung kann ebenso zur Bestimmung der Ausflusszeit bei anderen Temperaturen, wie zum Beispiel 25 °C, angewendet werden.
WARNUNG — Die Anwendung dieser Europäischen Norm kann den Umgang mit gefährlichen Sub-stanzen und Ausrüstungen sowie die Durchführung gefährlicher Arbeitsschritte einschließen. Diese Europäische Norm erhebt nicht den Anspruch, dass alle mit ihrer Anwendung verbundenen Sicher-heitsprobleme angesprochen werden. Es liegt in der Verantwortung des Anwenders dieser Europä-ischen Norm, geeignete Vorsichtsmaßnahmen für den Arbeits- und Gesundheitsschutz zu treffen und die Anwendbarkeit einschränkender Vorschriften vor der Anwendung zu bestimmen.

Bitumes et liants bitumineux - Détermination du temps d'écoulement à l'aide d'un viscosimètre à écoulement - Partie 1: Emulsions de bitume

La présente norme européenne spécifie une méthode de détermination du temps d’écoulement, en secondes,
à 40 °C, des émulsions de bitume, à l’aide d’un vis cosimètre à écoulement. Une autre température d’essai
possible est 50 °C.
NOTE Le mode opératoire décrit dans cette norme peut aussi être suivi pour déterminer le temps d’écoulement à
d’autres températures comme, par exemple, à 25 °C.
AVERTISSEMENT — L'utilisation de la présente Norme européenne peut impliquer le recours à des
produits, des opérations et des équipements à caractère dangereux. La présente Norme européenne
n'est pas censée aborder tous les problèmes de sécurité concernés par son usage. Il est de la
responsabilité de l'utilisateur de la présente Norme européenne d'établir des règles de sécurité et
d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.

Bitumen in bitumenska veziva - Določevanje viskoznosti bitumenskih emulzij z iztočnim viskozimetrom - 1. del: Bitumenske emulzije

Ta EN določa metodo za določevanje viskoznosti bitumenskih emulzij (1. del) ter rezanih in fluksiranih bitumenskih veziv (2. del) z uporabo iztočnega viskozimetra.

General Information

Status
Withdrawn
Publication Date
08-Mar-2011
Withdrawal Date
06-Dec-2022
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
07-Dec-2022

Relations

Buy Standard

Standard
EN 12846-1:2011
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels Ausflussviskosimeter - Teil 1: BitumenemulsionenBitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 1: Bituminous emulsions91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 12846-1:2011SIST EN 12846-1:2011en,fr,de01-junij-2011SIST EN 12846-1:2011SLOVENSKI
STANDARDSIST EN 12846:20031DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12846-1
March 2011 ICS 91.100.50 Supersedes EN 12846:2002English Version
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 1: Bituminous emulsions
Bitumes et liants bitumineux - Détermination du temps d'écoulement à l'aide d'un viscosimètre à écoulement - Partie 1: Emulsions de bitume
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels Ausflussviskosimeter - Teil 1: Bitumenemulsionen This European Standard was approved by CEN on 22 January 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12846-1:2011: ESIST EN 12846-1:2011

Specifications of thermometer . 12Bibliography . 13 SIST EN 12846-1:2011

Compared with the previous edition, EN 12846:2002, the scope and principle were detailed, Figure 2 was added, tolerances were specified or modified in the apparatus dimensions, details were added in the test procedure and measurements made and the test precision data were reviewed. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 12846-1:2011

Three forms are required, differing only in the size of the orifice (10 mm, 4 mm and 2 mm). For other dimensions of the cup and the ball-valve, see Figure 3. The cup cylinder shall be made of brass. The ball valve should be made of corrosion-resistant metal, with a ball on a rod, a levelling peg attached to the rod and a hemispherical top by means of which the valve may be supported in a vertical position. The viscometer cups shall be equipped with suitable corks or caps for closing the orifices with the ball valve in position, and some means of covering the cups (e.g. lids) to prevent evaporation of water and minimize surface cooling effects. The viscometer-cup holder shall be capable of:  supporting one or more cups in a vertical position;  providing a valve support to hold the valve at least 16 mm vertically above the orifice of the cup during efflux of the test material. NOTE 1 To enhance resistance to wear and corrosion of the ball and socket valve, the bottom of the cup may be made from a different, corrosion resistant, material and screwed to the brass tube. It is then advised to use the same material, such as for instance phosphor-bronze, for the cup bottom and the ball valve. Wrought nickel alloy with copper or metals NiCu30 in accordance with ISO 9722 are possible materials for the rod of the ball valve. SIST EN 12846-1:2011

6.4 Thermometers, two, conforming to the requirements described in Annex A. Other temperature measuring devices may be used instead of mercury stem thermometers. However, the mercury stem thermometer is the reference device. Therefore any alternative device employed shall be calibrated so as to provide the same readings as would be provided by the mercury stem thermometer, recognising and allowing for the fact of changed thermal response times compared with the mercury thermometer. When measuring and controlling nominally constant temperatures, as
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.