iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14733:2005+A1:2010

(Main)

Bitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control

Bitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control

This European Standard specifies Factory Production Control (FPC) requirements for use by the manufacturers of
bituminous emulsions, cut-back and fluxed binders.
This European Standard is applicable to the control of bituminous binders where the constituents and composition
are known, having been derived from a prescriptive specification or from the Initial Type Test (ITT) procedure for
demonstration of performance related properties described in the appropriate product standard or from a European
Technical Approval.
NOTE 1 Factory Production Control is a requirement of all harmonised elements of harmonised European Standards and
European Technical Approvals for bituminous binders if the CE mark of conformity is to be affixed. The system can also be
applied to non-harmonised elements and to situations where CE marking is not mandatory.
NOTE 2 Regulated properties of the products are involved in this document.

Bitumen und bitumenhaltige Bindemittel - Werkseigene Produktionskontrolle von Bitumenemulsionen, gefluxtem und verschnittenem Bitumen

Diese Europäische Norm legt Anforderungen an die werkseigene Produktionskontrolle (WPK) fest, die von den Herstellern von Bitumenemulsionen, verschnittenem und gefluxtem Bitumen anzuwenden sind.
Diese Europäische Norm gilt für die Kontrolle von bitumenhaltigen Bindemitteln, deren Bestandteile und Zusammensetzung bekannt sind, da sie aus einer vorschreibenden Spezifikation oder aus dem Erst-Typ-Prüfverfahren (ITT) für den Nachweis leistungsbezogener Eigenschaften, die in der entsprechenden Produk-tnorm beschrieben sind, oder aus einer Europäischen Technischen Zulassung entnommen wurden.
ANMERKUNG 1 Die werkseigene Produktionskontrolle ist eine Anforderung an alle harmonisierten Elemente von harmonisierten Europäischen Normen und Europäischen Technischen Zulassungen für bitumenhaltige Bindemittel, sofern das CE-Konformitätszeichen verwendet werden soll. Das System kann ebenso auf die nicht harmonisierten Elemente und in solchen Fällen angewendet werden, in denen eine CE-Kennzeichnung nicht verbindlich gefordert ist.
ANMERKUNG 2 In dieses Dokument wurden verbindlich vorgeschriebene Eigenschaften einbezogen.

Bitumes et liants bitumineux - Maîtrise de la production en usine des émulsions de bitume, des bitumes fluxés et fluidifiés

La présente Norme européenne spécifie les exigences relatives à la maîtrise de la production en usine (FPC),
à l'usage des producteurs d'émulsions de bitume, de liants fluidifiés et fluxés.
La présente Norme européenne est applicable à la maîtrise des liants bitumineux dont la nature des constituants et
leur teneur sont connues. Ces liants ayant été mis au point à partir soit de spécifications prescriptives, soit de la
procédure d'essai de type initial (ITT) destinée à révéler les propriétés reliées aux performances décrites dans la
norme appropriée relative au produit ou encore d’un Agrément Technique Européen.
NOTE 1 La maîtrise de la production en usine (FPC) est une exigence requise pour l'ensemble des éléments harmonisés
des Normes européennes harmonisées et des Agréments Techniques Européens (ETA) qui concernent les liants bitumineux,
lorsque la marque de conformité CE doit être apposée. Ce système peut aussi être appliqué à des éléments non harmonisés
et dans des cas où le marquage CE n'est pas obligatoire.
NOTE 2 Les propriétés réglementées des produits sont incluses dans le présent document.

Bitumen in bitumenska veziva - Kontrola proizvodnje v obratih za proizvodnjo bitumenskih emulzij ter fluksiranih in rezanih bitumnov

Ta evropski standard določa zahteve za kontrolo proizvodnje v obratih (FPC), ki jo uporabljajo proizvajalci bitumenskih emulzij, rezanih in fluksiranih bitumnov. Ta evropski standard se uporablja za nadzor bitumenskih veziv, kjer so sestavine in sestava znane in pridobljene iz predpisanih specifikacij ali s postopkom začetnega tipskega preskusa (ITT) za prikaz lastnosti, povezanih z delovanjem, opisanim v ustreznem standardu proizvoda ali v evropskih tehničnih soglasjih.

General Information

Status
Withdrawn
Publication Date
05-Oct-2010
Withdrawal Date
07-May-2013
ICS
75.140 - Waxes, bituminous materials and other petroleum products
91.100.50 - Binders. Sealing materials
Technical Committee
CEN/TC 336 - Bituminous binders
Drafting Committee
CEN/TC 336/WG 2 - Emulsions and fluxed bitumens
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
08-May-2013
Completion Date
08-May-2013
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/124 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on road construction products
Ref Project
SIST EN 14733:2005+A1:2011 - Bitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control

Relations

Merged From
EN 14733:2005 - Bitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control
Effective Date
19-Jan-2023
Merged From
EN 14733:2005/FprA1 - Bitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control
Effective Date
18-Jan-2023
Replaced By
EN 13808:2013 - Bitumen and bituminous binders - Framework for specifying cationic bituminous emulsions
Effective Date
08-Jun-2022
Replaced By
EN 15322:2013 - Bitumen and bituminous binders - Framework for specifying cut-back and fluxed bituminous binders
Effective Date
08-Jun-2022

Buy Standard

EN 14733:2005+A1:2011EN 14733:2005+A1:2011
PreviousNext
Standard
EN 14733:2005+A1:2011
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumen in bitumenska veziva - Kontrola proizvodnje v obratih za proizvodnjo bitumenskih emulzij ter fluksiranih in rezanih bitumnovBitumen und bitumenhaltige Bindemittel - Werkseigene Produktionskontrolle von Bitumenemulsionen, gefluxtem und verschnittenem BitumenBitumes et liants bitumineux - Maîtrise de la production en usine des émulsions de bitume, des bitumes fluxés et fluidifiésBitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 14733:2005+A1:2010SIST EN 14733:2005+A1:2011en,fr,de01-april-2011SIST EN 14733:2005+A1:2011SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14733:2005+A1
October 2010 ICS 75.140; 91.100.50 Supersedes EN 14733:2005English Version
Bitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control
Bitumes et liants bitumineux - Maîtrise de la production en usine des émulsions de bitume, des bitumes fluxés et fluidifiés
Bitumen und bitumenhaltige Bindemittel - Werkseigene Produktionskontrolle von Bitumenemulsionen, gefluxtem und verschnittenem Bitumen This European Standard was approved by CEN on 21 April 2005 and includes Amendment 1 approved by CEN on 16 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14733:2005+A1:2010: ESIST EN 14733:2005+A1:2011

April 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-08-16. This document supersedes EN 14733:2005. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Construction Products Directive 89/106/CE. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 14733:2005+A1:2011

Characterization of perceptible properties EN 1426, Bitumen and bituminous binders
Determination of needle penetration EN 1427, Bitumen and bituminous binders
Determination of the softening point
Ring and Ball method EN 1428, Bitumen and bituminous binders
Determination of water content in bitumen emulsions
Azeotropic distillation method EN 1429, Bitumen and bituminous binders
Determination of residue on sieving of bituminous emulsions and determination of storage stability by sieving EN 1431, !Bitumen and bituminous binders
Determination of residual binder and oil distillate from bitumen emulsions by distillation" !EN 12592, Bitumen and bituminous binders
Determination of solubility" EN 12595, Bitumen and bituminous binders
Determination of kinematic viscosity EN 12596, Bitumen and bituminous binders
Determination of dynamic viscosity by vacuum capillary !prEN 12846-1, Bitumen and bituminous binders
Determination of efflux time by the efflux viscometer
Part 1 : Bituminous emulsions" !prEN 12846-2, Bitumen and bituminous binders
Determination of efflux time by the efflux viscometer
Part 2 : Cut-back and fluxed bituminous binders" !EN 12847, Bitumen and bituminous binders
Determination of settling tendency of bituminous emulsions"
EN 12848, Bitumen and bituminous binders
Determination of mixing stability with cement of bituminous emulsions EN 12850, Bitumen and bituminous binders
Determination of the pH value of bituminous emulsions !prEN 13074-1:2008, Bitumen and bituminous binders
Recovery of binder from bituminous emulsion or from cut-back or fluxed bitumen by evaporation" SIST EN 14733:2005+A1:2011

Stabilisation of binder from bituminous emulsion or from cut-back or fluxed bitumen after recovery" EN 13075-1, Bitumen and bituminous binders
Determination of breaking behaviour
Part 1: Determination of breaking value of cationic bituminous emulsions, mineral filler method EN 13075-2, Bitumen and bituminous binders
Determination of breaking behaviour
Part 2: Determination of fines mixing time of cationic bituminous emulsions !EN 13302, Bitumen and bituminous binders
Determination of dynamic viscosity of bituminous binder using a rotating spindle apparatus" !deleted text" EN 13358, Bitumen and bituminous binders
Determination of the distillation characteristics of petroleum cut-back bitumen products !EN 13398, Bitumen and bituminous binders
Determination of the elastic recovery of modified bitumen" EN 13587, Bitumen and bituminous binders
Determination of the tensile properties of bituminous binders by the tensile test method EN 13588, Bitumen and bituminous binders
Determination of cohesion of bituminous binders with pendulum test EN 13589, Bitumen and bituminous binders
Determination of the tensile properties of modified bitumen by the force ductility method !EN 13614, Bitumen and bituminous binders
Determination of adhesivity of bitumen emulsions by water immersion test
Aggregate method" EN 13703, Bitumen and bituminous binders
Determination of deformation energy !EN 13808, Bitumen and bituminous binders
Framewor
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12594:2024(Main)
Bitumens and bituminous binders - Preparation of test samples
SIST EN 12594:2024

This document specifies methods for preparing test samples of bitumens and bituminous binders in order to test their properties.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12597:2024(Main)
Bitumens and bituminous binders - Terminology
SIST EN 12597:2024

This European Standard defines terms for paving or industrial bitumen of various types and binders derived from bitumen.
This European Standard is intended to cover materials only within the scope of CEN/TC 336, i.e. only bitumens and bituminous binders. It should consequently not extend to non-petroleum "hydrocarbon" binders such as coal tar and its derivatives or to natural asphalts. However, some definitions are given for some excluded materials and related terms. The corresponding terms were introduced only when they appeared in a definition of a product or process and when their definition was found necessary for understanding or for avoiding any ambiguity.

  • Draft
    24 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16346:2023(Main)
Bitumen and bituminous binders - Determination of breaking behaviour and immediate adhesivity of cationic bituminous emulsions
SIST EN 16346:2024

This document specifies a method for the determination of the breaking and immediate adhesivity behaviour of cationic bituminous emulsions in contact with aggregate. The method applies to emulsions used for surface dressing and similar applications and can be used for formulation as well as for production control purposes.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14769:2023(Main)
Bitumen and bituminous binders - Accelerated long-term ageing conditioning by a Pressure Ageing Vessel (PAV)
SIST EN 14769:2023

This document specifies an accelerated long-term ageing/conditioning procedure for bituminous binders. The procedure involves ageing trays of binder at elevated temperatures under pressurized conditions in a pressure ageing vessel (PAV).
NOTE   For binders to be used in hot and warm asphalt applications, the pre-conditioning of the sample can be performed using one of the methods in the EN 12607 series. For binders to be used in bituminous emulsion and cut back or fluxed applications, the stabilization of the sample is such that there are no volatiles remaining.
WARNING - The use of this document can involve hazardous materials, operations and equipment, in particular, the use of a high pressure ageing vessel. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate health and safety practices and determine the applicability of regulatory limitations prior to use. If there is the likelihood of volatile components being present in a binder, this procedure is not used.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12595:2023(Main)
Bitumen and bituminous binders - Determination of kinematic viscosity
SIST EN 12595:2023

This document specifies a method for the determination of the kinematic viscosity of bituminous binders at 60 °C and 135 °C, in a range from 6 mm2/s to 300 000 mm2/s. Other temperatures are possible if calibration constants are known. Bituminous emulsions are not covered within the scope of this method.
Results for this method can be used to calculate dynamic viscosity when the density of the test material is known or can be determined.
NOTE   This document assumes Newtonian behaviour of the sample at test conditions.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14770:2023(Main)
Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR)
SIST EN 14770:2023

This document specifies a general method of using a dynamic shear rheometer (DSR) for measuring the rheological properties of bituminous binders. The procedure involves determining the complex shear modulus and phase angle of binders over a range of test frequencies and test temperatures when tested in oscillatory shear.
From the test, the complex shear modulus, |G*|, and its phase angle, δ, at a given temperature and frequency are calculated, as well as the components G' and G" of the complex shear modulus.
This method is applicable to un-aged, aged, stabilized and recovered bituminous binders. The test procedure in accordance with this document is not applicable for bituminous binders with particles larger than 250 μm (e.g. filler material, granulated rubber).
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12596:2023(Main)
Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum capillary
SIST EN 12596:2023

This document specifies a method for the determination of the dynamic viscosity of bituminous binders by means of a vacuum capillary viscometer at 60 °C in a range between 0,003 6 Pa⋅s and 580 000 Pa⋅s. Other temperatures are possible if calibration constants are known. Bituminous emulsions and non-newtonian binders (e.g. some polymer modified bitumen) are not within the scope of this method.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14771:2023(Main)
Bitumen and bituminous binders - Determination of the flexural creep stiffness - Bending Beam Rheometer (BBR)
SIST EN 14771:2023

This document specifies a method for the determination of the flexural creep stiffness of bitumen and bituminous binders in the range of 30 MPa to 1 GPa by means of the bending beam rheometer.
The method can be applied to a variety of bitumens, including unmodified as well as modified binders, as fresh (unused) binders, as well as binders after laboratory ageing conditioning (e.g. EN 12607-1, EN 14769), and also binders that have been recovered from asphalt mixtures.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12847:2022(Main)
Bitumen and bituminous binders - Determination of settling tendency of bituminous emulsions
SIST EN 12847:2022

This document specifies a method for the determination of the settling tendency of bituminous emulsions.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17643:2022(Main)
Bitumen and bituminous binders - Determination of equi-shear modulus temperature and phase angle using a Dynamic Shear Rheometer (DSR) - BTSV test
SIST EN 17643:2022

This document specifies the Binder Fast Characterization Test (for short: BTSV test, German: Bitumen-Typisierungs-Schnell-Verfahren). The test is conducted using a Dynamic Shear Rheometer (DSR). It is used to characterize bitumen and bituminous binders and to assess the deformation behaviour at high service temperatures.
The test procedure described in this document covers the testing of paving grade bitumen or modified bitumen, as fresh (unused) binders, as well as binders after laboratory ageing conditioning (e.g. EN 12607-1, EN 14769), and also binders that have been recovered from asphalt mixtures. The test procedure in accordance with this document is not applicable for bituminous binders with particles larger than 250 μm (e.g. filler material, granulated rubber).
NOTE   The test procedure has not been applied on bituminous binders recovered from bitumen emulsions yet.
The test determines the temperature and the associated phase angle at which a bituminous binder exhibits a defined complex shear modulus in stress-controlled oscillation mode at constant frequency and with continuous increase of the test temperature.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to ensure that regulatory requirements are fulfilled prior to application of this document. This document involves handling of apparatus and binders at very high temperatures. Always wear protective gloves and eyewear when handling hot binders, and avoid contact with any exposed, unprotected skin.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day