iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1196:1998

(Main)

Domestic and non-domestic gas-fired air heaters - Supplementary requirements for condensing air heaters

Domestic and non-domestic gas-fired air heaters - Supplementary requirements for condensing air heaters

This standard specifies the additional requirements and test methods for gas-fired air heaters which are so designed that water vapour condenses from combustion products.  On this subject it extends the European standards EN 778 and EN 1319 for domestic, and EN 621 and EN 1020 for non-domestic air heaters.  This standard applies to gas-fired air heaters with or without a fan in the combustion circuit in one of the following constructional types:  ð an integral air heater with at least one condensing heat exchanger;  ð a non-condensing air heater with an integrated additional condensing heat exchanger;  ð a non-condensing air heater, with an integrated additional condensing heat exchanger for the recovery of heat from combustion products and from ventilation air if appropriate.  This European Standard covers type-testing only.

Gasbefeuerte Warmlufterzeuger für den häuslichen und den nicht-häuslichen Gebrauch - Zusätzliche Anforderungen an kondensierende Warmlufterzeuger

Diese Norm legt die zusätzliche Anforderungen und Prüfverfahren für gasbefeuerte Warmlufterzeuger fest, die so ausgelegt sind, daß der Wasserdampf aus den Abgasen kondensiert. In dieser Hinsicht ergänzt sie die Europäischen Normen EN 778 und prEN 1319 (Warmlufterzeuger für den häuslichen Gebrauch) sowie EN 621 und EN 1020 (Warmlufterzeuger für den nicht-häuslichen Gebrauch). Diese Norm gilt für gasbefeuerte Warmlufterzeuger mit oder ohne Gebläse im Verbrennungskreis in einer der folgenden Bauweisen: - ein kompletter Warmlufterzeuger mit mindestens einem kondensierenden Wärmetauscher;...

Générateurs d'air chaud à usage domestique et non domestique utilisant les combustibles gazeux - Exigences complémentaires pour les générateurs d'air chaud à condensation

La présente norme définit les exigences et les méthodes d'essais complémentaires visant les générateurs d'air chaud à gaz conçus pour exploiter la condensation des produits de combustion. Elle complète sur ce point les normes européennes EN 778 et le prEN 1319 visant les générateurs d'air chaud à usage domestique et EN 621 et EN 1020 visant les générateurs d'air chaud à usage non domestique.

Plinski grelniki zraka – Dodatne zahteve za kondenzacijske grelnike

General Information

Status
Withdrawn
Publication Date
16-Jun-1998
Withdrawal Date
16-Aug-2011
ICS
91.140.10 - Central heating systems
Technical Committee
CEN/TC 180 - Non-domestic gas-fired overhead radiant heaters
Drafting Committee
CEN/TC 180 - Non-domestic gas-fired overhead radiant heaters
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
17-Aug-2011
Completion Date
17-Aug-2011
Directive
2009/142/EC - DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 November 2009 relating to appliances burning gaseous fuels
90/396/EEC - Appliances burning gaseous fuels
Mandate
M/BC/CEN/89/6 - Standardization request to CEN concerning appliances burning gaseous fuels
Ref Project
SIST EN 1196:1999 - Domestic and non-domestic gas-fired air heaters - Supplementary requirements for condensing air heaters

Relations

Replaced By
EN 1196:2011 - Domestic and non-domestic gas-fired air heaters - Supplementary requirements for condensing air heaters
Effective Date
20-Aug-2011

Buy Standard

EN 1196:1999EN 1196:1999
PreviousNext
Standard
EN 1196:1999
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Plinski grelniki zraka – Dodatne zahteve za kondenzacijske grelnikeGasbefeuerte Warmlufterzeuger für den häuslichen und den nicht-häuslichen Gebrauch - Zusätzliche Anforderungen an kondensierende WarmlufterzeugerGénérateurs d'air chaud a usage domestique et non domestique utilisant les combustibles gazeux - Exigences complémentaires pour les générateurs d'air chaud a condensationDomestic and non-domestic gas-fired air heaters - Supplementary requirement
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15502-2-2:2024(Main)
Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances
SIST EN 15502-2-2:2024

This document specifies, the requirements and test methods concerning the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners and are hereafter referred to as “boilers”.
Where the word boiler is used, this is intended to be read as the boiler including its connecting ducts, ducts and terminals, if any.
This document covers gas-fired central heating boilers type B11, B11BS, B12, B12BS, B13, B13BS:
NOTE 1   For further background information on appliance types see EN 1749:2020.
a)   that have a nominal heat input (on the basis of net calorific value) not exceeding 70 kW;
b)   that use one or more combustible gases of the three gas families at the pressures stated in EN 437:2021;
c)   where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation;
d)   where the maximum operating pressure in the water circuit does not exceed 6 bar;
e)   which are declared in the technical instructions to be either a “low temperature boiler” or a “standard boiler”. If no declaration is given the boiler is to be considered a “standard boiler”;
f)   which are intended to be installed inside a building or in a partially protected place;
g)   which are intended to produce also hot water either by the instantaneous or storage principle, as a single unit;
h)   which are designed for either sealed water systems or for open water systems.
NOTE 2   This document provides requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this document, the risk associated with this alternative construction needs to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This document does not cover all the requirements for:
aa)   appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex AB);
ab)   appliances using flue dampers;
ac)   appliances that have a nominal heat input (on the basis of net calorific value) exceeding 70 kW;
ad)   appliances of the types A, B14, B¬2, B3, B4, B5 and C;
ae)   appliances intended to be connected to a (common) flue having mechanical extraction;
af)   appliances with gas/air ratio control;
ag)   modular boilers;
ah)   boilers which can give rise to condensation under certain circumstances;
ai)   boilers intended to be installed in a room with a foreseeable negative pressure relative to the pressure in the flue system;
aj)   surface temperatures of external parts particular to children and elderly people;
ak)   appliances that are intended to burn natural gases of the second family where hydrogen is added to the natural gas;
al)   boilers intended to be installed in areas accessible to elderly people and children;
am)   boilers equipped with an adaptive combustion control function (ACCF).
NOTE   Negative pressure relative to the pressure in the flue system can for example be caused by mechanical or thermal ventilation in airtight buildings.

  • Draft
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17956:2024(Main)
Energy efficiency classes for technical insulation systems - Calculation method and applications
SIST EN 17956:2024

This document is applicable to technical insulation systems of operational installations in industry and the building services, such as pipes, ducts, vessels, equipment and built-in components.
The document specifies methods for the energy efficiency classification of insulation systems for the abovementioned components with an operational temperature range of −30 °C up to 650 °C.
The document addresses plant operators, engineers of operational installations, as well as the involved contractors such as insulation contractors and pipefitting contractors.
The design of safe surface temperatures for personal protection, as well as the prevention of condensation, is outside the scope of this document.
This document also does not apply to water-based heating and cooling systems in buildings and does not apply to directly buried district heating and district cooling pipes.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 15502-3-1:2024(Main)
Gas-fired central heating boilers - Part 3-1: H2NG and ACCF - Expansion of EN 15502-2-1:2022
SIST-TS CEN/TS 15502-3-1:2024

Scope of CEN/TS 15502-3-1
EN 15502-2-1:2022, Clause 1 applies with the following modifications:
Add after k):
l) which are fully premixed appliances equipped with an Adaptive Combustion Control Function (ACCF) that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance including gas grids for natural gases of the second family where up to 20% hydrogen volume is added to the natural gas (H2NG-Y20).
m) which are fully premixed appliances equipped with a Pneumatic Gas Air Ratio controller (PGAR) that are intended to be connected to gas grids for natural gases of the second family where up to 20% hydrogen volume is added to the natural gas (H2NG-Y20), where the quality of the distributed gas without adding the hydrogen is not likely to vary to a large extent over the lifetime of the appliance.
Replace ab) and ak) and al) by the following:
ab) appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex AB of EN 15502-1:2021), except for fully premixed appliances with a ACCF, as ACCF appliances are designed to adapt to variations in gas quality.
ak) appliances that are intended to burn natural gases of the second family where hydrogen is added to the natural gas, except for fully premixed appliances with a ACCF or PGAR (which are covered by this document);
al) Partially premixed appliances equipped with an adaptive combustion control function (ACCF).

  • Draft
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15502-1:2021+A1:2023(Main + Amendment)
Gas-fired heating boilers - Part 1: General requirements and tests
SIST EN 15502-1:2022+A1:2024

This European Standard specifies the common requirements and test methods, as well as the classification, marking and energy labelling of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This European Standard is to be used in conjunction with the specific Parts 2 (Part 2-1 and following ones).
This European Standard applies to boilers of types B and C.
NOTE For further background information on appliance types see CEN/TR 1749:2014 [1].
a) that use one or more combustible gases of the three gas families at the pressures stated in EN 437;
b) where the temperature of the water is below or above 105 °C during normal operation;
c) where the maximum operating pressure in the water circuit does not exceed 6 bar;
d) which can give rise to condensation under certain circumstances;
e) which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler" or an "other boiler". If no declaration is given the boiler is to be considered both a "standard boiler" and an "other boiler";
NOTE The Ecodesign Directive defines "other boilers", "low temperature boilers" and "condensing boilers". The Boiler Efficiency Directive defines "standard boilers", "low temperature boilers" and "condensing boilers". Depending on the legislation applied, a boiler can be both "a standard boiler" and an "other boiler"."
f) which are intended to be installed inside a building or in a partially protected place;
g) which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.
This European Standard applies to boilers designed for sealed water systems or for open water systems.
NOTE This general standard and the specific standards (see Part 2) provide requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard or a specific standard, the risk associated with this alternative construction will need to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard is not intended to cover appliances intended for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex EE).
This European Standard is not intended to cover appliances designed and constructed to burn gas containing toxic components.

  • Standard
    213 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15502-2-1:2022+A1:2023(Main + Amendment)
Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW
SIST EN 15502-2-1:2022+A1:2024

This document specifies the requirements and test methods, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as "boilers".
This document is intended to be used in conjunction with EN 15502-1:2021.
This document covers gas-fired central heating boilers from the types C1 up to C(11) and the types B2, B3 and B5:
NOTE 1   For further background information on appliance types see EN 1749:2020.
a)   that have a nominal heat input (on the basis of net calorific value) not exceeding 1 000 kW;
b)   that use one or more combustible gases of the three gas families at the pressures stated in EN 437:2021;
c)   where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation;
d)   where the maximum operating pressure in the water circuit does not exceed 6 bar;
e)   which can give rise to condensation under certain circumstances;
f)   which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler"; if no declaration is given the boiler is to be considered a "standard boiler";
g)   which are intended to be installed inside a building or in a partially protected place;
h)   which are intended to produce also hot water either by the instantaneous or storage principle as a single unit;
i)   which are designed for either sealed water systems or for open water systems;
j)   which are either modular boilers, or non-modular boilers.
k)   which are from the types C(10) that are equipped with a gas-air ratio control and that have a ∆pmax, saf(min) of 25 Pa, and C(11) that have condensing boiler modules that are equipped with a gas-air ratio control and that have a ∆pmax, saf(min) of 25 Pa.
NOTE 2   This document provides requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard, the risk associated with this alternative construction needs to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This document does not cover all the requirements for:
aa)   appliances above 1 000 kW;
ab)   appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex AB of EN 15502-1:2021);
ac)   appliances using flue dampers;
ad)   appliances of the types B21, B31, B51, C21, C41, C51, C61, C71, C81, C(12) and C(13);
ae)   C7 appliances that have a nominal heat input (on the basis of net calorific value) exceeding 70 kW;
af)   appliances incorporating flexible plastic flue liners;
ag)   C(10) boilers:
1)   without a gas-air ratio control, or
2)   which are non-condensing appliances, or
3)   which have a maximum safety pressure difference at minimum heat input not equal to 25 Pa (∆pmax, saf(min));
ah)   C(11) boilers that have boiler modules:
1)   without a gas-air ratio control, or
2)   which are non-condensing appliances, or
3)   which have a maximum safety pressure difference at minimum heat input not equal to 25 Pa (∆pmax, saf(min));
ai)   appliances intended to be connected to a flue having mechanical extraction;
aj)   surface temperatures of external parts particular to children and elderly people;
ak)   appliances that are intended to burn natural gases of the second family where hydrogen is added to the natural gas;
al)   appliances equipped with an adaptive combustion control function (ACCF);
am)   boilers intended to be installed in areas accessible to elderly people and children.

  • Standard
    105 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17690-1:2023(Main)
Components for BAC control loop - Sensors - Part 1: Room temperature sensors
SIST EN 17690-1:2024

This document specifies requirements and test methods for room temperature sensors used to control the room temperature.
This document is applicable to wall mounted and flush mounted room temperature sensors.
The following aspects are not covered by this document:
-   pendulum temperature sensors;
-   ceiling mounted temperature sensor;
-   extract air temperature sensors.
NOTE   The measured value available at the output of the sensor is influenced by the place where the sensor device is located and factors such as air velocity, wall temperature, self/waste heating of the device and the air temperature. The perceived temperature, which is important for the well-being of a person, depends among other factors on air temperature, temperature of the surrounding walls and air flow rate as indicated in EN ISO 7730.
The temperature sensor element can be combined with other sensors in one device. This document only deals with the room temperature sensing of this devices. Other sensors are not covered except of their influence on the room temperature sensing (e.g. self-heating).
This document specifies sensor characteristics contributing to the determination of the control accuracy of individual zone controller according to EN 15500 1.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15502-2-3:2023(Main)
Gas-fired central heating boilers - Part 2-3: Specific standard for hybrid units combining a gas-fired boiler and an electrical heat pump in a product
SIST EN 15502-2-3:2024

This document specifies the requirements and tests methods concerning the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of hybrid units.
A hybrid unit is composed of:
-   a gas boiler as a heat generator which is able to supply the heat demand in all operating conditions;
-   an electrical air-to-water heat pump, as a heat generator, which does not have to meet the heat demand in all operating conditions;
-   a control unit (see definition 3.1.10).
A hybrid unit can include the facility to produce hot water, either by the instantaneous or storage principle, the whole being marketed as a single unit.
A gas boiler as part of a hybrid unit covered by this document is a gas-fired central heating boiler from the types C1 up to C9 and the types B2, B3 and B5, according to the classification in EN 1749:2020:
a)   that have a nominal heat input (on the basis of gross calorific value) not exceeding 400 kW;
b)   that use one or more combustible gases of the three gas families at the pressures stated in EN 437:2021;
c)   where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation;
d)   where the maximum operating pressure in the water circuit does not exceed 6 bar;
e)   which are classified as a gas-fired central heating boiler;
f)   which are intended to be installed either indoors or outdoors in a partially protected place;
g)   which are designed for either sealed water systems or for open water systems.
This document provides requirements for boilers with known constructions.
NOTE 1   For boilers with any alternative constructions, which might not fully be covered by this document, the risk associated with this alternative construction needs to be assessed.
NOTE 2   An example of an assessment methodology, based upon risk assessment and which covers the essential requirements of the Gas Appliance Regulation UE/426/2016, is given in Clause 11.
This document does not cover all the requirements for:
aa)   appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see EN 15502-1:2021, Annex AB);
ab)   appliances using flue dampers;
ac)   appliances of the types B21, B31, B51, C21, C41, C51, C61, C71 and C81;
ad)   appliances incorporating flexible plastic flue liners;
ae)   appliances designed to become connected to a combined flue duct system.
af)   appliances of the types C(10),C(11), C(12) and C(13);
ag)   C7 appliances that have a nominal heat input (on the basis of net calorific value) exceeding 70 kW;
ah)   appliances intended to be connected to a flue having mechanical extraction;
ai)   surface temperatures of external parts particular to children and elderly people;
aj)   appliances that are intended to burn natural gases of the second family where hydrogen is added to the natural gas;
ak)   appliances equipped with an adaptive combustion control function (ACCF);
al)   boilers intended to be installed in areas accessible to elderly people and children.
This document specifies minimum operating requirements which ensure that the products are fit for the use designated by the technical instructions when used for space heating and/or DHW production.
This document is intended to be used in conjunction with:
ba)   the gas-fired boiler, the generic part EN 15502-1:2021 and specific parts FprEN 15502-2-1:2022 and FprEN 15502-2-2:2022;
bb)   the electrical heat pump, EN 14511-4:2018, EN 378-1:2016+A1:2020, EN 378-2:2016 and EN 14825:2022;
bc)   electrical safety, EN 60335-1:2012 , EN 60335-2-102:2016 and IEC 60335-2-40:2018;
bd)   for domestic hot water production, EN 13203-5:2022.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17522:2023(Main)
Design and construction of backfilled and grouted borehole heat exchangers
SIST EN 17522:2023

This document covers standardization in the field of geological and environmental aspects, design, construction, operation, monitoring, maintenance and decommissioning of grouted borehole heat exchangers for uses in geothermal energy systems.
This document is only applicable for backfilled and grouted boreholes, it is not applicable for groundwater-filled boreholes.
Direct expansion and thermal syphon techniques are excluded from this document.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 12098-6:2022(Main)
Energy performance of buildings - Controls for heating systems - Part 6: Accompanying TR EN 12098-1:2022 - Modules M3-5,6,7,8
SIST-TP CEN/TR 12098-6:2023

This document refers to EN 12098-1:2022, Energy performance of buildings - Controls for heating systems - Part 1: Control equipment for hot water heating systems - Modules M3-5, 6, 7, 8.
It contains information to support the correct understanding, use and national adaption of EN 12098-1:2022.
This document does not contain any normative provisions.

  • Technical report
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12098-1:2022(Main)
Energy performance of buildings - Controls for heating systems - Part 1: Control equipment for hot water heating systems - Modules M3-5, 6, 7, 8
SIST EN 12098-1:2023

This document is applicable to electronic control equipment for heating systems with water as the heating medium and a supply water temperature up to 120 °C.
This control equipment controls the distribution and/or the generation of heat in relation to the outside temperature and time and other reference variables.
This document also is also applicable to controllers that contain an integrated optimum start or an optimum start-stop control function.
Safety requirements on heating systems remain unaffected by this document.
The dynamic behaviour of the valves and actuators are not covered in this document.
A multi-distribution and/or multi-generation system needs a coordinated solution to prevent undesired interaction and is not part of this document.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day