iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13523-29:2024

(Main)

Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping)

Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping)

This part of the EN 13523 series specifies a procedure for the comparative evaluation of resistance to soiling of an organic coating on a metallic substrate (coil coating) in an outdoor exposure environment, particularly the soiling defect known as "Tiger stripes".

Bandbeschichtete Metalle - Prüfverfahren - Teil 29: Beständigkeit gegen Verschmutzung (Schmutzaufnahme und Streifenbildung)

Tôles prélaquées - Méthodes d'essai - Partie 29 : Résistance à la pollution environnementale (salissures)

Le présent document spécifie un mode opératoire à appliquer pour déterminer, par comparaison, la résistance à la pollution d’un revêtement organique appliqué sur un subjectile métallique (prélaquage en bandes continues) dans un environnement d’exposition à l’extérieur, en particulier la salissure appelé « zébrures ».
En plus des zébrures, d’autres types de rétention de salissure peuvent être observés.

Prevlečene kovine, ki se navijajo - Preskusne metode - 29. del: Odpornost proti onesnaženju iz okolja (nabiranje nesnage in nastanek prog)

General Information

Status
Published
Publication Date
23-Apr-2024
ICS
25.220.60 - Organic coatings
Technical Committee
CEN/TC 139 - Paints and varnishes
Drafting Committee
CEN/TC 139/WG 9 - Testing of coil coated metals
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
24-Apr-2024
Due Date
06-Aug-2025
Completion Date
24-Apr-2024
Ref Project
oSIST prEN 13523-29:2023 - Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping)

Relations

Replaces
EN 13523-29:2017 - Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
Effective Date
03-May-2023

Buy Standard

prEN 13523-29:2023 - BARVEprEN 13523-29:2023 - BARVE
PreviousNext
Draft
prEN 13523-29:2023 - BARVE
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13523-29:2023
01-september-2023
Prevlečene kovine, ki se navijajo - Preskusne metode - 29. del: Odpornost proti
onesnaženju iz okolja (nabiranje nesnage in nastanek prog)
Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt
pick-up and striping)
Bandbeschichtete Metalle - Prüfverfahren - Teil 29: Beständigkeit gegen Verschmutzung
(Schmutzaufnahme und Streifenbildung)
Tôles prélaquées - Méthodes d'essai - Partie 29 : Résistance à la pollution
environnementale (salissures)
Ta slovenski standard je istoveten z: prEN 13523-29
ICS:
13.020.40 Onesnaževanje, nadzor nad Pollution, pollution control
onesnaževanjem in and conservation
ohranjanje
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-29:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13523-29:2023

---------------------- Page: 2 ----------------------
oSIST prEN 13523-29:2023


DRAFT
EUROPEAN STANDARD
prEN 13523-29
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2023
ICS 25.220.60 Will supersede EN 13523-29:2017
English Version

Coil coated metals - Test methods - Part 29: Resistance to
environmental soiling (Dirt pick-up and striping)
Tôles prélaquées - Méthodes d'essai - Partie 29 : Bandbeschichtete Metalle - Prüfverfahren - Teil 29:
Résistance à la pollution environnementale (salissures) Beständigkeit gegen Verschmutzung
(Schmutzaufnahme und Streifenbildung)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-29:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13523-29:2023
prEN 13523-29:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus and materials . 5
6 Sample preparation . 6
7 Procedure . 6
8 Evaluation . 7
9 Test report .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13523-12:2024(Main)
Coil coated metals - Test methods - Part 12: Resistance to scratching
oSIST prEN 13523-12:2023

This document specifies the procedure for determining the resistance of an organic coating on a metallic substrate to penetration by scratching with a needle.
It is possible that with some aluminium alloys and thin gauge steel substrate below 0,4 mm, that rather than scratching, the needle will deform the substrate. Under these conditions, this test method is not applicable.
Soft coatings such as poly vinyl chloride (PVC) and structured coatings will not give a precise result due to the soft nature of the coating and/or the potential for the needle to snag.
The method is not applicable to conductive coatings.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-8:2024(Main)
Coil coated metals - Test methods - Part 8: Resistance to salt spray (fog)
oSIST prEN 13523-8:2023

This part of The EN 13523 series specifies the procedures for determining the resistance to salt spray (fog) of an organic coating on a metallic substrate (coil coating).
For steel, neutral salt spray (fog) is usually used, and for aluminium, acetic acid salt spray (fog).

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-1:2024(Main)
Coil coated metals - Test methods - Part 1: Film thickness
oSIST prEN 13523-1:2023

This document specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Five appropriate methods are given in this document:
a)   magnetic induction;
b)   eddy current;
c)   micrometer;
d)   optical;
e)   ruggedized optical interference.
The methods are applicable only to products with smooth and flat substrates, but the coating itself can be textured. In that case, for methods a) and b), the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness, method d) can provide the minimum, maximum and average thickness, and e) will give the total thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness are only applicable on method a).

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-22:2024(Main)
Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison
oSIST prEN 13523-22:2023

This document specifies the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth.
NOTE   Results can differ between natural and artificial daylight.
It might be that two colour specimens will match in daylight but not under another light source. This phenomenon is known as metamerism (see EN 13523 3).
If a metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) can be made, in accordance with EN 13523 3.
No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore, this procedure is only intended to be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours, etc.).
The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results. This practice is essential for critical colour matching and is highly recommended for colour inspections.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-21:2024(Main)
Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels
oSIST prEN 13523-21:2023

This part of the EN 13523 series specifies the procedure for evaluating the behaviour of an organic coating on a metallic substrate during and after outdoor exposure. Panel design, preparation and the procedure for outdoor exposure are performed in accordance with EN 13523 19.
After washing of the panel, some dirt can remain on the panel. This remaining dirt can influence the accuracy and precision of readings of gloss and colour, performed on exposed panels, although carried out in accordance with the standards. Unlike other precise measurements, the objective of this European Standard is to report on trends in the corrosion and/or paint degradation behaviour of coil coated panels.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-3:2024(Main)
Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison
oSIST prEN 13523-3:2023

This document specifies procedures for determining the instrumental colour difference (CIELAB   or  ) of an organic coating on a metallic substrate compared to another one used as a reference (usually called reference) and the metamerism depending on the illuminant.
When two colour specimens have identical spectral reflectance curves, they are matching under any illuminant irrespective of its spectral characteristics. This is termed a “spectral match”. It is also possible for two colour specimens having different spectral reflectance curves to match visually under a given light source but not to match under another light source with different spectral characteristics; such matches are termed "metameric".
One quantitative description of metamerism is the so-called "metamerism index".
Information on the metamerism index is of limited value where ΔE (instrumental colour difference for a given illuminant) is > 0,5. The metamerism index is not suited for determining the absolute colour difference or colour consistency of a given specimen at change of illuminant.
The colour difference under the reference illuminant is to be measured in colour coordinates L*, a* and b*.
Excluded from this method are organic coatings producing fluorescence and/or which are multicoloured, pearlescent or metallic.
Establishing a reference as well as the magnitude of an acceptable colour difference are not covered by this method.
Two methods are given in this document:
a)   instrumental colour difference measurement using a tristimulus colourimeter;
b)   instrumental colour difference measurement using a spectrophotometer or equivalent.
It is advised that care is taken when measuring e.g.
-   textured surfaces;
-   fluorescent coatings;
-   metameric coatings;
-   multi-coloured, pearlescent, metallic or special colour effect coatings.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-10:2024(Main)
Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation
oSIST prEN 13523-10:2023

This part of the EN 13523 series specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions.
Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected.
Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-23:2023(Main)
Coil coated metals - Test methods - Part 23: Resistance to humid atmospheres containing sulfur dioxide
SIST EN 13523-23:2023

This document describes the procedure for determining the resistance of an organic coating on a metallic substrate to humid atmospheres containing sulfur dioxide.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-14:2023(Main)
Coil coated metals - Test methods - Part 14: Chalking (Helmen method)
SIST EN 13523-14:2023

This document describes the procedure for determining objectively the chalking resulting from natural or artificial weathering of an organic coating on a metallic substrate.
The advantage of this procedure for measuring chalking of an organic coating is that the result can be read off immediately on an instrument. Subjective judgement by visual comparison of test specimens with reference specimens is not necessary.
Reproducible results can only be obtained by careful execution of the test. Special attention is paid to the adhesive tape and its application to the test surface.
The test method is not applicable to embossed coatings. In the case of textured coatings, the degree of texture will influence readings. Also, dirt collection can influence readings on outdoor weathered specimens.
NOTE   Different methods for assessing chalking are in use. The results of these different methods are not comparable.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-26:2022(Main)
Coil coated metals - Test methods - Part 26: Resistance to condensation of water
SIST EN 13523-26:2022

This document specifies a procedure for evaluating the resistance to continuous condensation of an organic coating on a metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day