EN ISO 15792-2:2020

Welding consumables - Test methods - Part 2: Preparation of single-run and two-run technique test pieces and specimens in steel (ISO 15792-2:2020)

This document specifies the preparation of butt weld test pieces and specimens.
The test pieces and specimens are used to determine the strength and impact properties of welded joints when testing welding consumables with single-run and two-run techniques.
This document is applicable to welding consumables for arc welding of steel.
This document is not suitable for electro-slag or electro-gas welding.

Schweißzusätze - Prüfverfahren - Teil 2: Vorbereitung von Prüfstücken und Proben zur Prüfung von Einlagen- und Lage/Gegenlage-Schweißungen an Stahl (ISO 15792 2:2020)

Dieses Dokument legt die Herstellung der Prüfstücke für Stumpfnähte und der Proben fest.
Die Prüfstücke und Proben werden zur Bestimmung der Festigkeits- und Kerbschlagbiegeeigenschaften von Schweißverbindungen bei der Prüfung von Schweißzusätzen mit Einlagen- und Lage/Gegenlage-Schweißung verwendet.
Dieses Dokument ist für Schweißzusätze für das Lichtbogenschweißen von Stahl anzuwenden.
Dieses Dokument ist nicht anwendbar für das Elektroschlackeschweißen oder das Elektrogasschweißen.

Produits consommables pour le soudage - Méthodes d'essai - Partie 2: Préparation de pièces d'essai et d'éprouvettes en une ou deux passes en acier (ISO 15792-2:2020)

Le présent document spécifie la préparation des pièces d'essai et des éprouvettes en soudage bout à bout.
Les pièces d'essai et les éprouvettes sont utilisées pour déterminer les propriétés de résistance mécanique et de flexion par choc des assemblages soudés lors de l'essai des produits consommables utilisés en soudage avec une ou deux passes.
Le présent document est applicable aux produits consommables destinés au soudage à l'arc de l'acier.
Le présent document n'est pas adapté au soudage sous laitier ou au soudage électrogaz.

Dodajni in pomožni materiali za varjenje - Preskusne metode - 2. del: Priprava zvarnega spoja in preskušancev za preskus enostranskega in dvostranskega varjenja jekel (ISO 15792-2:2020)

General Information

• Status: Published
• Publication Date: 15-Sep-2020
• Withdrawal Date: 30-Mar-2021
• ICS: 25.160.20 - Welding consumables
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/WG 3 - Welding consumables
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 16-Sep-2020
• Completion Date: 16-Sep-2020
• Ref Project: SIST EN ISO 15792-2:2020 - Welding consumables - Test methods - Part 2: Preparation of single-run and two-run technique test pieces and specimens in steel (ISO 15792-2:2020)

Relations

• Replaces: EN ISO 15792-2:2008 - Welding consumables - Test methods - Part 2: Preparation of single-run and two-run technique test specimens in steel (ISO 15792-2:2000)
• Effective Date: 28-Aug-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15792-2:2020
01-november-2020
Nadomešča:
SIST EN ISO 15792-2:2008
Dodajni in pomožni materiali za varjenje - Preskusne metode - 2. del: Priprava
zvarnega spoja in preskušancev za preskus enostranskega in dvostranskega
varjenja jekel (ISO 15792-2:2020)
Welding consumables - Test methods - Part 2: Preparation of single-run and two-run
technique test pieces and specimens in steel (ISO 15792-2:2020)
Schweißzusätze Prüfverfahren - Teil 2: Vorbereitung von Prüfstücken und Proben zur
Prüfung von Einlagen- und Lage/Gegenlage-Schweißungen an Stahl (ISO 15792
2:2020)
Produits consommables pour le soudage - Méthodes d'essai - Partie 2: Préparation de
pièces d'essai et d'éprouvettes en une ou deux passes en acier (ISO 15792-2:2020)
Ta slovenski standard je istoveten z: EN ISO 15792-2:2020
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 15792-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 15792-2:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 15792-2:2020


EN ISO 15792-2
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2020
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 15792-2:2008
English Version

Welding consumables - Test methods - Part 2: Preparation
of single-run and two-run technique test pieces and
specimens in steel (ISO 15792-2:2020)
Produits consommables pour le soudage - Méthodes Schweißzusätze Prüfverfahren - Teil 2: Vorbereitung
d'essai - Partie 2: Préparation de pièces d'essai et von Prüfstücken und Proben zur Prüfung von Einlagen-
d'éprouvettes en une ou deux passes en acier (ISO und Lage/Gegenlage-Schweißungen an Stahl (ISO
15792-2:2020) 15792 2:2020)
This European Standard was approved by CEN on 29 August 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15792-2:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 15792-2:2020
EN ISO 15792-2:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 15792-2:2020
EN ISO 15792-2:2020 (E)
European foreword
This document (EN ISO 15792-2:2020) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15792-2:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
Un
...