EN ISO 20342-1:2019/prA1
(Amendment)Assistive products for tissue integrity when lying down - Part 1: General requirements - Amendment 1 (ISO 20342-1:2019/DAM 1:2021)
Assistive products for tissue integrity when lying down - Part 1: General requirements - Amendment 1 (ISO 20342-1:2019/DAM 1:2021)
Unterstützende Produkte zur Gewebeintegrität im Liegen - Teil 1: Allgemeine Festlegungen - Änderung A1 (ISO 20342-1:2019/DAM 1:2021)
No scope available
Produits d'assistance pour l'intégrité des tissus en position allongée - Partie 1: Exigences générales - Amendement 1 (ISO 20342-1:2019/DAM 1:2021)
Tehnični pripomočki za celovitost tkiv v ležečem položaju - 1. del: Splošne zahteve - Dopolnilo 1 (ISO 20342-1:2019/DAM 1:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 20342-1:2019/oprA1:2021
01-september-2021
Tehnični pripomočki za celovitost tkiv v ležečem položaju - 1. del: Splošne zahteve
- Dopolnilo 1 (ISO 20342-1:2019/DAM 1:2021)
Assistive products for tissue integrity when lying down - Part 1: General requirements -
Amendment 1 (ISO 20342-1:2019/DAM 1:2021)
Unterstützende Produkte zur Gewebeintegrität im Liegen - Teil 1: Allgemeine
Festlegungen (ISO 20342-1:2019/DAM 1:2021)
Produits d'assistance pour l'intégrité des tissus en position allongée - Partie 1: Exigences
générales - Amendement 1 (ISO 20342-1:2019/DAM 1:2021)
Ta slovenski standard je istoveten z: EN ISO 20342-1:2019/prA1
ICS:
11.180.01 Pripomočki za Aids for disabled and
onesposobljene in handicapped persons in
hendikepirane osebe na general
splošno
SIST EN ISO 20342-1:2019/oprA1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 20342-1:2019/oprA1:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 20342-1:2019/oprA1:2021
DRAFT AMENDMENT
ISO 20342-1:2019/DAM 1
ISO/TC 173 Secretariat: SIS
Voting begins on: Voting terminates on:
2021-06-15 2021-09-07
Assistive products for tissue integrity when lying down —
Part 1:
General requirements
AMENDMENT 1
Produits d'assistance pour l'intégrité des tissus en position allongée —
Partie 1: Exigences générales
AMENDEMENT 1
ICS: 11.180.01
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 20342-1:2019/DAM 1:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
---------------------- Page: 3 ----------------------
SIST EN ISO 20342-1:2019/oprA1:2021
ISO 20342-1:2019/DAM 1:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
SIST EN ISO 20342-1:2019/oprA1:2021
ISO 20342-1:2019/DAM 1:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adh
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.