iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 13267:2023

(Main)

Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)

Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)

This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

Kunststoff-Rohrleitungssysteme aus Thermoplasten für erdverlegte drucklose Abwasserkanäle und -leitungen - Böden von Kontroll- und Einsteigschächten aus Thermoplasten - Prüfverfahren für die Widerstandsfähigkeit gegen Einbeulen (ISO 13267:2022)

Dieses Dokument legt Prüfverfahren für die Widerstandsfähigkeit des Schachtbodens von Kontroll- und Einsteigschächten aus thermoplastischen Kunststoffen gegen äußeren Boden- und Wasserdruck nach dem Einbau fest.

Systèmes de canalisations thermoplastiques pour branchements et collecteurs d'assainissement enterrés sans pression - Éléments de fond de boîtes d'inspection et de branchement et de regards thermoplastiques - Méthode d'essai de résistance au flambage (ISO 13267:2022)

Le présent document spécifie des méthodes d’essai permettant de déterminer la résistance de l’élément de fond des boîtes d’inspection et de branchement et des regards thermoplastiques par rapport à la pression externe du sol et de l’eau souterraine après installation.

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Plastomerni revizijski in vstopni jaški - Metode preskušanja odpornosti proti uklonu (ISO 13267:2022)

Ta dokument določa metode preskušanja odpornosti dna termoplastnih revizijskih jaškov in vstopnih jaškov na pritisk, ki ga povzroča zunanja zemlja in podtalnica po vgradnji.

General Information

Status
Published
Publication Date
10-Jan-2023
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
91.140.80 - Drainage systems
93.030 - External sewage systems
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 20 - Thermoplastics ancillaries for soil and waste discharge and gravity buried drainage and sewerage systems
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
11-Jan-2023
Due Date
08-Oct-2024
Completion Date
11-Jan-2023
Ref Project
SIST EN ISO 13267:2023 - Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)

Relations

Replaces
EN 14830:2006 - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance
Effective Date
01-Jun-2022

Buy Standard

EN ISO 13267:2023EN ISO 13267:2023
PreviousNext
Standard
EN ISO 13267:2023
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13267:2023
01-april-2023
Nadomešča:
SIST EN 14830:2007
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Plastomerni revizijski in vstopni
jaški - Metode preskušanja odpornosti proti uklonu (ISO 13267:2022)
Thermoplastics piping systems for non-pressure underground drainage and sewerage -
Thermoplastics inspection chamber and manhole bases - Test methods for buckling
resistance (ISO 13267:2022)
Kunststoff-Rohrleitungssysteme aus Thermoplasten für erdverlegte drucklose
Abwasserkanäle und -leitungen - Böden von Kontroll- und Einsteigschächten aus
Thermoplasten - Prüfverfahren für die Widerstandsfähigkeit gegen Einbeulen (ISO
13267:2022)
Systèmes de canalisations thermoplastiques pour branchements et collecteurs
d'assainissement enterrés sans pression - Éléments de fond de boîtes d'inspection et de
branchement et de regards thermoplastiques - Méthode d'essai de résistance au
flambage (ISO 13267:2022)
Ta slovenski standard je istoveten z: EN ISO 13267:2023
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN ISO 13267:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 13267:2023

---------------------- Page: 2 ----------------------
SIST EN ISO 13267:2023


EN ISO 13267
EUROPEAN STANDARD

NORME EUROPÉENNE

January 2023
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 91.140.80; 93.030 Supersedes EN 14830:2006
English Version

Thermoplastics piping systems for non-pressure
underground drainage and sewerage - Thermoplastics
inspection chamber and manhole bases - Test methods for
buckling resistance (ISO 13267:2022)
Systèmes de canalisations thermoplastiques pour Kunststoff-Rohrleitungssysteme aus Thermoplasten
branchements et collecteurs d'assainissement enterrés für erdverlegte drucklose Abwasserkanäle und -
sans pression - Éléments de fond de boîtes d'inspection leitungen - Böden von Kontroll- und Einsteigschächten
et de branchement et de regards thermoplastiques - aus Thermoplasten - Prüfverfahren für die
Méthode d'essai de résistance au flambage (ISO Widerstandsfähigkeit gegen Einbeulen (ISO
13267:2022) 13267:2022)
This European Standard was approved by CEN on 2 January 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13267:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 13267:2023
EN ISO 13267:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 13267:2023
EN ISO 13267:2023 (E)
European foreword
The text of ISO 13267:2022 has been prepared by Technical Committee ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 13267:2023 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2023, and conflicting national standards shall be
withdrawn at the latest by July 2023.
Attention is draw
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 13266:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading (ISO 13266:2022)
SIST EN ISO 13266:2023

This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material.
NOTE    Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13268:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (ISO 13268:2022)
SIST EN ISO 13268:2023

This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-4:2018/A1:2021(Amendment)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes - Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test results (ISO 11296-4:2018/Amd 1:2021)
SIST EN ISO 11296-4:2018/A1:2021

2021-02-11 - TC decision is missing to skip FV.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-7:2019(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes (ISO 11296-7:2019)
SIST EN ISO 11296-7:2019

This document, in conjunction with ISO 11296-1, specifies requirements and test methods for pipes which are formed on site by spirally winding and jointing a pre-manufactured profiled plastics strip, or a profiled plastics strip and integral locking joiner strip, and used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to spirally-wound pipes of fixed or variable diameter made of profiled plastics strips, with or without steel stiffening elements, and installed by one of two methods.
The first method employs a dedicated winding machine in front of the open end of an existing pipeline, e.g. in a manhole. The pipes thus formed are simultaneously inserted into the existing pipeline by the winding forces, and by certain techniques can also be expanded in diameter after or during insertion.
The second method employs a dedicated winding machine which forms the pipe as it traverses the existing pipeline from one manhole to the next.
It applies to profiled plastics strips of unplasticized poly(vinyl chloride) (PVC U) with integral locking mechanism, or of high density polyethylene (HDPE) with integrally welded joints.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11297-3:2018(Main)
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes (ISO 11297-3:2018)
SIST EN ISO 11297-3:2018

This document, in conjunction with ISO 11297‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe.
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE       For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-3:2018(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
SIST EN ISO 11296-3:2018

This document, in conjunction with ISO 11296‑1, specifies requirements and test methods for close-fit lining systems used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U) as manufactured, as well to the installed lining system with its associated joints.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11297-1:2018(Main)
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 1: General (ISO 11297-1:2018)
SIST EN ISO 11297-1:2018

ISO 11297-1:2018 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground drainage and sewerage networks under pressure, including both hydraulically and pneumatically pressurized systems. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or any non-structural sprayed coatings or annular filler.
ISO 11297-1:2018 gives the general requirements co

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-1:2018(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General (ISO 11296-1:2018)
SIST EN ISO 11296-1:2018

ISO 11296-1:2018 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground non-pressure drainage and sewerage networks, which are operated as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar[1]. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or any non-structural sprayed coatings or annular filler.
ISO 11296-1:2018 gives the general requirements common to all relevant renovation techniques.
[1] 1 bar = 0,1 MPa = 0,1 N/mm2 = 105 N/m2.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-4:2018(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2018)
SIST EN ISO 11296-4:2018

ISO 11296-4:2018, in conjunction with ISO 11296‑1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks with service temperatures up to 50 °C.
ISO 11296-4:2018 applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.3).

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-2:2018(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018)
SIST EN ISO 11296-2:2018

ISO 11296-2:2018, in conjunction with ISO 11296-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground non-pressure drainage and sewerage networks. It is applicable to polyethylene (PE) pipes of three different types:
-      PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
-      PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
-      PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"), see Annex A.
In addition, ISO 11296-2:2018 covers:
-      jointing of pipe lengths by means of butt fusion;
-      fabricated and injection-moulded fittings made of PE.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day