EN ISO 21487:2018
(Main)Small craft - Permanently installed petrol and diesel fuel tanks (ISO 21487:2012, including Amd 1:2014 and Amd 2:2015)
Small craft - Permanently installed petrol and diesel fuel tanks (ISO 21487:2012, including Amd 1:2014 and Amd 2:2015)
ISO 21487:2012 establishes requirements for design and test of petrol and diesel fuel tanks for internal combustion engines that are intended to be permanently installed in small craft of up to 24 m length of hull.
For installation requirements, ISO 10088 applies.
Kleine Wasserfahrzeuge — Fest eingebaute Ottokraftstoff- und Dieselkraftstofftanks (ISO 21487:2012)
Diese Internationale Norm legt Anforderungen an die Konstruktion und die Prüfung von fest eingebauten Ottokraftstoff- und Dieselkraftstofftanks für Verbrennungsmotoren auf kleinen Wasserfahrzeugen mit einer Rumpflänge bis 24 m fest.
Für Anforderungen an die Installation ist ISO 10088 anzuwenden.
Petits navires - Réservoirs à carburant à essence et diesel installés à demeure (ISO 21487:2012, y compris Amd 1:2014 et Amd 2:2015)
L'ISO 21487:2012 établit des exigences sur la conception et les essais des réservoirs à carburant essence et diesel pour les moteurs à combustion interne et destinés à être installés à demeure sur des bateaux d'une longueur de coque inférieure ou égale à 24 m.
L'ISO 10088 s'applique pour ce qui concerne les exigences d'installation.
Mala plovila - Trajno vgrajeni rezervoarji za bencinsko in dizelsko gorivo (ISO 21487:2012, vključno z dopolniloma A1:2014 in A2:2015)
Mednarodni standard določa zahteve za načrtovanje in preskušanje rezervoarjev za bencinsko in dizelsko gorivo za motorje z notranjim zgorevanjem, ki so namenjeni trajni vgradnji v mala plovila z dolžino trupa do 24 m. Zahteve glede namestitve so določene v standardu ISO 10088.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 21487:2013
SIST EN ISO 21487:2013/A1:2015
SIST EN ISO 21487:2013/A2:2016
0DODSORYLOD7UDMQRYJUDMHQLUH]HUYRDUML]DEHQFLQVNRLQGL]HOVNRJRULYR ,62
YNOMXþQR]GRSROQLORPD$ LQ$
Small craft - Permanently installed petrol and diesel fuel tanks (ISO 21487:2012,
including Amd 1:2014 and Amd 2:2015)
Kleine Wasserfahrzeuge - Fest eingebaute Ottokraftstoff- und Dieselkraftstofftanks (ISO
21487:2012, einschließlich Amd 1:2014 und Amd 2:2015)
Petits navires - Réservoirs à carburant à essence et diesel installés à demeure (ISO
21487:2012, y compris Amd 1:2014 et Amd 2:2015)
Ta slovenski standard je istoveten z: EN ISO 21487:2018
ICS:
47.020.20 Ladijski motorji Marine engines and
propulsion systems
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 21487
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 21487:2012
English Version
Small craft - Permanently installed petrol and diesel fuel
tanks (ISO 21487:2012, including Amd 1:2014 and Amd
2:2015)
Petits navires - Réservoirs à carburant à essence et Kleine Wasserfahrzeuge - Fest eingebaute
diesel installés à demeure (ISO 21487:2012, y compris Ottokraftstoff- und Dieselkraftstofftanks (ISO
Amd 1:2014 et Amd 2:2015) 21487:2012, einschließlich Amd 1:2014 und Amd
2:2015)
This European Standard was approved by CEN on 16 April 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21487:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4
European foreword
The text of ISO 21487:2012, including Amd 1:2014 and Amd 2:2015 has been prepared by Technical
Committee ISO/TC 188 “Small craft” of the International Organization for Standardization (ISO) and has
been taken over as EN ISO 21487:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 21487:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 21487:2012, including Amd 1:2014 and Amd 2:2015 has been approved by CEN as EN ISO
21487:2018 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I and Annex II of
Directive 2013/53/EU
Essential Requirements of Clause(s)/sub- Remarks/Notes
Directive 2013/53/EU clause(s) of this EN
Annex I, Part A, 5.2.2 – Fuel tanks 4, 5, 6, 7, 8 This standard deals with the design
and test of petrol and diesel fuel tanks
and tank openings only.
This standard does not deal with the
ventilation of fuel tank spaces;
protection against fire from the
engine and other sources of ignition
and heat or separation from living
quarters.
Annex II - Components of In respect of fuel tanks and their
watercraft; (4) - Fuel tanks intended 4, 5, 6, 7, 8 openings when placed on the Union
for fixed installations and fuel hoses. market separately.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 21487
Second edition
2012-11-15
Small craft — Permanently installed
petrol and diesel fuel tanks
Petits navires — Réservoirs à carburant à essence et diesel installés à
demeure
Reference number
ISO 21487:2012(E)
©
ISO 2012
ISO 21487:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 21487:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General properties . 2
4.1 Resistance to liquids in contact . 2
4.2 Copper-based alloys . 2
4.3 Provisions to tanks . 2
4.4 Installation of non-integral tanks . 3
5 Petrol fuel tanks: design and tests . 3
5.1 Design . 3
5.2 Tests to be performed . 3
6 Diesel fuel tanks: design and tests . 4
6.1 Design . 4
6.2 Tests to be performed . 4
7 Tests . 4
7.1 General . 4
7.2 Hydraulic pressure test . 4
7.3 Pressure-impulse type test for petrol fuel tanks . 6
7.4 General fire-resistance test of non-metallic fuel tanks . 6
7.5 As-installed fire-resistance test of non-metallic fuel tanks . 7
8 Marking . 8
ISO 21487:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 21487 was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 21487:2006), which has been technically revised.
It also incorporates the Technical Corrigendum ISO 21487:2006/Cor.1:2008. The main changes from the first
edition are the following:
— diesel tanks shall be equipped with inspection hatch(es) for cleaning and inspection (4.3.10);
— metallic tanks may be static pressure tested as an alternative to the pressure-impulse test (5.2.2);
— non-metallic, non-integral tanks, if installed in an engine compartment, shall be fire tested (6.2.3);
— non-metallic tanks shall be marked with the maximum temperature to which the tank may be exposed (Clause 8).
iv © ISO 2012 – All rights reserved
INTERNATIONAL STANDARD ISO 21487:2012(E)
Small craft — Permanently installed petrol and diesel fuel tanks
1 Scope
This International Standard establishes requirements for design and test of petrol and diesel fuel tanks for internal
combustion engines that are intended to be permanently installed in small craft of up to 24 m length of hull.
For installation requirements, ISO 10088 applies.
2 Normative references
The following referenced do
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.