CEN ISO/TS 15877-7:2018

Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2018)

This part of ISO 15877 gives guidance for the assessment of conformity of materials, products, and assemblies in accordance with the applicable part(s) of ISO 15877 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of  certification procedures.
In conjunction with the other parts of ISO 15877 (see Foreword), this Technical Specification (International Standard) is applicable to Chlorinated poly(vinyl chloride) (PVC-C) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 15877-1:2009).

Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-C) - Teil 7: Empfehlungen für die Beurteilung der Konformität (ISO/TS 15877-7:2018)

Dieses Dokument enthält Anforderungen und Empfehlungen für die Beurteilung der Konformität von Werkstoffen, Produkten und Bauteilkombinationen, die, in Übereinstimmung mit den/dem entsprechenden Teil(en) von ISO 15877, als Teil des Qualitätsmanagementsystems im Qualitätssicherungsplan des Herstellers und für die Erstellung von Zertifizierungsverfahren vorgesehen sind.
ANMERKUNG   Als Hilfe für den Leser enthält Anhang A eine grundlegende Prüfmatrix.
Zusammen mit den übrigen Teilen von ISO 15877 (siehe Vorwort) gilt dieses Dokument für Rohrleitungssysteme aus chloriertem Polyvinylchlorid (PVC C), die in der Warm- und Kaltwasserinstallation innerhalb von Gebäuden für die Durchleitung von Trink- oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen unter Berücksichtigung des betreffenden Systembetriebsdruckes und der für die jeweilige Anwendungsklasse geltenden Temperaturen (siehe ISO 15877 1:2009, Tabelle 1) eingesetzt werden.

Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Poly(chlorure de vinyle) chloré (PVC-C) - Partie 7: Guide pour l'évaluation de la conformité (ISO/TS 15877-7:2018)

Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Klorirani polivinilklorid (PVC-C) - 7. del: Navodilo za ugotavljanje skladnosti (ISO/TS 15877-7:2018)

Ta del standarda ISO 15877 vsebuje navodila za ugotavljanje skladnosti materialov, izdelkov in sestavov z ustreznimi deli standarda ISO 15877, ki naj bi se vključila v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti, vsebuje pa tudi navodila za vzpostavitev postopka certificiranja. Ta tehnična specifikacija (mednarodni standard) se v povezavi z drugimi deli standarda ISO 15877 (glej predgovor) uporablja za cevne sisteme iz kloriranega polivinilklorida (PVC-C), ki se uporabljajo za napeljave z vročo in hladno vodo za prenos pitne in nepitne vode v stavbah (gospodinjski sistemi), ter za sisteme ogrevanja glede na predvidene tlake in temperature v skladu z razredom uporabe (glej tabelo 1 v standardu ISO 15877-1:2009).

General Information

• Status: Published
• Publication Date: 18-Dec-2018
• ICS: 23.040.01 - Pipeline components and pipelines in general
• ICS: 23.040.20 - Plastics pipes
• ICS: 91.140.60 - Water supply systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 16 - Systems for hot and cold water applications
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 19-Dec-2018
• Due Date: 08-Jan-2019
• Completion Date: 19-Dec-2018
• Ref Project: SIST-TS CEN ISO/TS 15877-7:2019 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2018)

Relations

• Replaces: CEN ISO/TS 15877-7:2009 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2009)
• Effective Date: 12-Apr-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2019
1DGRPHãþD
SIST-TS CEN ISO/TS 15877-7:2009
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
.ORULUDQLSROLYLQLONORULG39&&GHO1DYRGLOR]DXJRWDYOMDQMHVNODGQRVWL
,6276
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl
chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-
7:2018)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes
Polyvinylchlorid (PVC-C) - Teil 7: Empfehlungen für die Beurteilung der Konformität
(ISO/TS 15877-7:2018)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Poly(chlorure de vinyle) chloré (PVC-C) - Partie 7: Guide pour l'évaluation de la
conformité (ISO/TS 15877-7:2018)
Ta slovenski standard je istoveten z: CEN ISO/TS 15877-7:2018
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

CEN ISO/TS 15877-7
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
December 2018
TECHNISCHE SPEZIFIKATION
ICS 91.140.60; 23.040.20; 23.040.01 Supersedes CEN ISO/TS 15877-7:2009
English Version
Plastics piping systems for hot and cold water installations
- Chlorinated poly(vinyl chloride) (PVC-C) - Part 7:
Guidance for the assessment of conformity (ISO/TS 15877-
7:2018)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Poly(chlorure de Kaltwasserinstallation - Chloriertes Polyvinylchlorid
vinyle) chloré (PVC-C) - Partie 7: Guide pour (PVC-C) - Teil 7: Empfehlungen für die Beurteilung der
l'évaluation de la conformité (ISO/TS 15877-7:2018) Konformität (ISO/TS 15877-7:2018)
This Technical Specification (CEN/TS) was approved by CEN on 29 October 2018 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 15877-7:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (CEN ISO/TS 15877-7:2018) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 15877-7:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO/TS 15877-7:2018 has been approved by CEN as CEN ISO/TS 15877-7:2018 without any
modification.
TECHNICAL ISO/TS
SPECIFICATION 15877-7
Third edition
2018-11
Plastics piping systems for hot and
cold water installations — Chlorinated
poly(vinyl chloride) (PVC-C) —
Part 7:
Guidance for the assessment of
conformity
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Poly(chlorure de vinyle) chloré (PVC-C) —
Partie 7: Guide pour l'évaluation de la conformité
Reference number
ISO/TS 15877-7:2018(E)
©
ISO 2018
ISO/TS 15877-7:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO/TS 15877-7:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 4
5 General . 5
6 Testing and inspection . 5
6.1 Grouping . 5
6.1.1 General. 5
6.1.2 Pressure groups . 5
6.1.3 Size groups . 5
6.1.4 Fitting groups . 6
6.2 Type testing (TT) . 6
6.3 Batch release tests (BRT) .11
6.4 Process verification tests (PVT) .12
6.5 Audit tests (AT) .13
6.6 Indirect tests (IT) .14
6.7 Test records.14
Annex A (informative) Basic test matrix .15
Bibliography .16
ISO/TS 15877-7:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical
Committee TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2,
Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO/TS 15877-7:2009), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— Addition of new definitions of the terms “material”, compound” and “material grade”;
— Revision of 6.2 “Type testing (TT)” with a special focus on Table 4.
A list of all parts in the ISO 15877 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved

ISO/TS 15877-7:2018(E)
Introduction
This document can be used to support elaboration of national third party certification procedures for
products conforming to the applicable part(s) of ISO 15877.
This document is a part of a System Standard for plastics piping systems of a particular material for a
specified application. There are a number of such System Standards.
At the date of publication of this document, System Standards for piping systems of other plastics
mate
...